EN 16842-10:2020

SLOVENSKI STANDARD
01-december-2020
Vozila za talni transport - Gnana vozila za talni transport - Vidno polje voznika -
Preskusna metoda in preverjanje - 10. del: Vlačilci in vlečni traktorji ter tovorna
vozila
Powered industrial trucks - Visibility - test methods and verification - Part 10: Towing and
Pushing tractors and Burden carrier
Kraftbetriebene Flurförderzeuge - Sichtverhältnisse - Prüfverfahren und Verifikation - Teil
10: Schlepper und Schubschlepper und Lastentransportfahrzeuge
Chariots de manutention automoteurs - Visibilité - Méthodes d'essai et vérification -
Partie 10 : Tracteur, pousseur et transporteur de charge
Ta slovenski standard je istoveten z: EN 16842-10:2020
ICS:
53.060 Industrijski tovornjaki Industrial trucks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 16842-10
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2020
EUROPÄISCHE NORM
ICS 53.060
English Version
Powered industrial trucks - Visibility - Test methods and
verification - Part 10: Towing and Pushing tractors and
Burden carrier
Chariots de manutention automoteurs - Visibilité - Kraftbetriebene Flurförderzeuge - Sichtverhältnisse -
Méthodes d'essai et vérification - Partie 10 : Tracteur, Prüfverfahren und Verifikation - Teil 10: Schlepper und
pousseur et transporteur de charge Schubschlepper und Lastentransportfahrzeuge
This European Standard was approved by CEN on 5 July 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16842-10:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative reference(s) . 5
3 Terms and definitions . 6
4 Truck configuration . 6
5 Test equipment . 6
6 Test procedures for direct visibility. 6
6.1 General . 6
6.2 Lighting equipment position . 7
6.2.1 General . 7
6.2.2 Sit-on operated trucks . 7
6.2.3 Stand-on operated trucks . 7
6.3 Test paths for tractors and burden carriers. 9
6.4 Measurement procedure . 9
6.5 Test procedure for indirect visibility. 10
7 Acceptance criteria . 10
7.1 General . 10
7.2 Direct visibility . 10
7.2.1 General . 10
7.2.2 Travelling visibility . 10
7.2.3 Manoeuvring visibility . 10
7.3 Indirect visibility . 10
7.4 Criteria for tractors . 11
7.5 Criteria for burden carriers . 12
8 Test report . 13
9 Information for use . 13

European foreword
This document (EN 16842-10:2020) has been prepared by Technical Committee CEN/TC 150
“Industrial Trucks - Safety”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2021, and conflicting national standards
shall be withdrawn at the latest by February 2021.
This document is intended to be used in combination with the requirements in EN 16842-1.
EN 16842 consists of the following parts under the general title Powered industrial trucks – Visibility –
Test methods and verification:
— Part 1: General requirements;
— Part 2: Sit-on counterbalance trucks and rough terrain masted trucks up to and including
10 000 kg capacity;
— Part 3: Reach trucks up to and including 10 000 kg capacity;
— Part 4: Industrial variable-reach trucks up to and including 10 000 kg capacity;
— Part 5: Industrial variable-reach trucks greater than 10 000 kg capacity;
— Part 6: Sit-on counterbalance trucks and rough terrain masted trucks greater than 10 000 kg
capacity;
— Part 7: Variable-reach and masted container trucks handling freight containers of 6 m (20 ft) length
and longer;
— Part 8: Stand-on counterbalance trucks up to and including 10 000 kg capacity;
— Part 9: Order-picking, lateral- and front-stacking trucks with elevating operator position;
— Part 10: Towing and Pushing tractors and Burden carrier.
It is intended to develop additional parts related to the following machinery:
— Pallet-stacking trucks (rider controlled);
— Single side loader;
— Multi-directional forklift truck;
— Articulated counterbalance lift truck;
— Non-Stacking low-lift straddle carriers (as defined in ISO 5053-1:2020, 3.18);
— Stacking high-lift straddle carriers (as defined in ISO 5053-1:2020, 3.19).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Introduction
This document is a type-C standard as stated in EN ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the
market players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events
are covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-
B standards, the requirements of this type-C standard take precedence over the requirements of the
other standards for machines that have been designed and built according to the requirements of this
type-C standard.”
1 Scope
This document specifies the requirements and test procedures for 360° visibility of sit-on and stand-on
self-propelled
— towing and pushing tractors in accordance with ISO 5053-1:2020, 3.1 and 3.2 without load and
without trailer;
— burden carriers in accordance with ISO 5053-1:2020, 3.25 without load; and
— baggage and equipment tractors with driver's accommodation in accordance with EN 12312-15,
without load and without trailer
(herein after referred to as trucks) and is intended to be used in conjunction with EN 16842-1.
Where specific requirements in this part are modified from the general requirements in EN 16842-1,
the requirements of this part are truck specific and are used for sit-on and stand-on self-propelled
Towing and Pushing tractors and Burden carriers.
This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events
relevant to the visibility of the operator for applicable machines when used as intended and under
conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not apply to personnel carriers in accordance with ISO 5053-1:2020, 3.25.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12312-15, Aircraft ground support equipment - Specific requirements - Part 15: Baggage and
equipment tractors
EN 16842-1:2018, Powered industrial trucks - Visibility - Test methods and verification - Part 1: General
requirements
EN ISO 3691-1:2015, Industrial trucks - Safety requirements and verification - Part 1: Self-propelled
industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks
(ISO 3691-1:2011, including Cor 1:2013)
EN ISO 3691-6:2015, Industrial trucks - Safety requirements and verification - Part 6: Burden and
personnel carriers (ISO 3691-6:2013)
ISO 5053-1:2020, Industrial trucks - Vocabulary - Part 1: Types of industrial trucks
EN ISO 5353, Earth-moving machinery, and tractors and machinery for agriculture and forestry - Seat
index point (ISO 5353:1995)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 16842-1:2018 and
ISO 5053-1:2020, and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
NOTE Definition 3.1 of EN 16842-1:2018 is not applicable for trucks covered by this part.
3.1
truck profile
contour which is determined by the largest width and
...