EN 12897:2016+A1:2020
(Main)Water supply - Specification for indirectly heated unvented (closed) storage water heaters
Water supply - Specification for indirectly heated unvented (closed) storage water heaters
EN 12897:2016+A1 specifies the constructional and performance requirements and methods of test for indirectly heated, unvented (closed) storage water heaters of up to 2 000 l volume suitable for connection to a water supply at a pressure between 0,05 MPa and 1,0 MPa (0,5 bar and 10 bar), and fitted with control and safety devices designed to prevent the temperature of the stored drinking water from reaching 95 °C. Whilst storage water heaters intended primarily for direct heating are not covered by this document, it does allow the provision of electric heating elements for auxiliary use.
Wasserversorgung - Bestimmung für mittelbar beheizte, unbelüftete (geschlossene) Speicher-Wassererwärmer
Dieses Dokument legt die Anforderungen an die Konstruktionstechnik und die Leistung und Prüfverfahren für mittelbar (indirekte) beheizte, unbelüftete (geschlossene) Speicher Wassererwärmer bis zu 2 000 l Volumen fest, die für den Anschluss an ein Wasserversorgungssystem bei einem Druck zwischen 0,05 MPa und 1,0 MPa (0,5 bar und 10 bar) geeignet und mit Regel und Sicherheitseinrichtungen ausgerüstet sind, die so ausgelegt sind, dass die Temperatur des gespeicherten Trinkwassers 95 °C nicht übersteigt.
Obwohl dieses Dokument keine Speicher Wassererwärmer behandelt, die hauptsächlich für direkte Er-wärmung vorgesehen sind, lässt es die Bereitstellung von elektrischen Heizelementen zu Hilfszwecken zu.
Alimentation en eau - Prescriptions pour préparateurs d'eau chaude par accumulation à chauffage indirect non ouverts à l'air libre (fermés)
Oskrba z vodo - Specifikacija za posredno ogrevane neprezračevane (zaprte) akumulacijske grelnike vode
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2020
Oskrba z vodo - Specifikacija za posredno ogrevane neprezračevane (zaprte)
akumulacijske grelnike vode
Water supply - Specification for indirectly heated unvented (closed) storage water
heaters
Wasserversorgung - Bestimmung für mittelbar beheizte, unbelüftete (geschlossene)
Speicher-Wassererwärmer
Alimentation en eau - Prescriptions pour préparateurs d'eau chaude par accumulation à
chauffage indirect non ouverts à l'air libre (fermés)
Ta slovenski standard je istoveten z: EN 12897:2016+A1:2020
ICS:
91.140.65 Oprema za ogrevanje vode Water heating equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 12897:2016+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2020
EUROPÄISCHE NORM
ICS 91.140.65
English Version
Water supply - Specification for indirectly heated
unvented (closed) storage water heaters
Alimentation en eau - Prescriptions pour préparateurs Wasserversorgung - Bestimmung für mittelbar
d'eau chaude par accumulation à chauffage indirect beheizte, unbelüftete (geschlossene) Speicher-
non ouverts à l'air libre (fermés) Wassererwärmer
This amendment A1 modifies the European Standard EN 12897:2016; it was approved by CEN on 9 October 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12897:2016+A1:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols . 8
4 Requirements . 8
4.1 Constructional requirements . 8
4.1.1 Inspection access . 8
4.1.2 Draining . 8
4.1.3 Hydraulic connections . 8
4.2 Temperature control . 9
4.3 Mechanical resistance and stability . 9
4.3.1 Pressure resistance of water storage vessel . 9
4.3.2 Pressure resistance of primary heater. 9
4.3.3 Durability . 9
4.3.4 Leakage test on double-walled primary heater . 11
4.4 Safety equipment. 11
4.4.1 General . 11
4.4.2 Energy cut-out device . 11
4.4.3 Temperature relief valve . 11
4.4.4 Pressure relief/expansion valve . 11
4.4.5 Pressure reducing valve . 11
4.4.6 Provision for expansion . 12
4.4.7 Backflow prevention . 12
5 Marking . 12
6 Evaluation of conformity . 12
6.1 General . 12
6.1.1 Compliance testing . 12
6.1.2 Market surveillance . 13
6.2 Initial type testing . 13
6.2.1 General . 13
6.2.2 Actual volume . 13
6.2.3 Rated storage volume . 13
6.2.4 Hot water volume . 13
6.2.5 Primary heating power (heat exchanger performance) . 14
6.2.6 Durability testing . 14
6.2.7 Double-walled primary heaters . 14
6.2.8 Standing heat loss . 14
6.2.9 Pressure resistance . 14
6.2.10 Temperature control devices . 14
6.2.11 Heat exchanger pressure drop . 14
6.3 Production testing . 14
6.4 Factory production control (FPC) . 15
7 Technical documents . 15
7.1 General . 15
7.2 Assembly and maintenance instructions . 15
7.3 Operating instructions . 16
Annex A (normative) Hot water safety and performance testing . 17
A.1 Tests required . 17
A.2 Test apparatus and tolerances . 17
A.3 Performance tests . 19
A.4 Interpretation and calculation of hot water performance results . 21
A.5 Function of safety devices. 22
Annex B (normative) Measurement of standing heat loss for factory insulated storage
water heaters . 23
B.1 General . 23
B.2 Apparatus . 23
B.3 Test Procedure . 25
B.4 Calculation of Results . 26
Annex C (informative) Inspection access . 28
Annex ZA (informative) !Relationship between this European Standard and the
requirements of Commission Delegated Regulation (EU) No 812/2013 of 18
February 2013 supplementing Directive 2010/30/EU regarding energy labelling of
water heaters, hot water storage tanks and packages of water heater and solar
device . 30
Annex ZB (informative) !Relationship between this European Standard and the
requirements of Commission Regulation (EU) No 814/2013 of 2 August 2013
implementing Directive 2009/125/EC with regard to ecodesign requirements for
water heaters and hot water storage tanks . 32
Bibliography . 34
European foreword
This document (EN 12897:2016+A1:2020) has been prepared by Technical Committee CEN/TC 164
“Water supply”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2020, and conflicting national standards
shall be withdrawn at the latest by August 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document includes Amendment 1 approved by CEN on 2019-10-09.
This document supersedes !EN 12897:2016".
The start and finish of text introduced or altered by amendment is indicated in t
...
SLOVENSKI STANDARD
01-april-2020
Nadomešča:
SIST EN 12897:2016
Oskrba z vodo - Specifikacija za posredno ogrevane neprezračevane (zaprte)
akumulacijske grelnike vode
Water supply - Specification for indirectly heated unvented (closed) storage water
heaters
Wasserversorgung - Bestimmung für mittelbar beheizte, unbelüftete (geschlossene)
Speicher-Wassererwärmer
Alimentation en eau - Prescriptions pour préparateurs d'eau chaude par accumulation à
chauffage indirect non ouverts à l'air libre (fermés)
Ta slovenski standard je istoveten z: EN 12897:2016+A1:2020
ICS:
91.140.65 Oprema za ogrevanje vode Water heating equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 12897:2016+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2020
EUROPÄISCHE NORM
ICS 91.140.65
English Version
Water supply - Specification for indirectly heated
unvented (closed) storage water heaters
Alimentation en eau - Prescriptions pour préparateurs Wasserversorgung - Bestimmung für mittelbar
d'eau chaude par accumulation à chauffage indirect beheizte, unbelüftete (geschlossene) Speicher-
non ouverts à l'air libre (fermés) Wassererwärmer
This amendment A1 modifies the European Standard EN 12897:2016; it was approved by CEN on 9 October 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12897:2016+A1:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols . 8
4 Requirements . 8
4.1 Constructional requirements . 8
4.1.1 Inspection access . 8
4.1.2 Draining . 8
4.1.3 Hydraulic connections . 8
4.2 Temperature control . 9
4.3 Mechanical resistance and stability . 9
4.3.1 Pressure resistance of water storage vessel . 9
4.3.2 Pressure resistance of primary heater. 9
4.3.3 Durability . 9
4.3.4 Leakage test on double-walled primary heater . 11
4.4 Safety equipment. 11
4.4.1 General . 11
4.4.2 Energy cut-out device . 11
4.4.3 Temperature relief valve . 11
4.4.4 Pressure relief/expansion valve . 11
4.4.5 Pressure reducing valve . 11
4.4.6 Provision for expansion . 12
4.4.7 Backflow prevention . 12
5 Marking . 12
6 Evaluation of conformity . 12
6.1 General . 12
6.1.1 Compliance testing . 12
6.1.2 Market surveillance . 13
6.2 Initial type testing . 13
6.2.1 General . 13
6.2.2 Actual volume . 13
6.2.3 Rated storage volume . 13
6.2.4 Hot water volume . 13
6.2.5 Primary heating power (heat exchanger performance) . 14
6.2.6 Durability testing . 14
6.2.7 Double-walled primary heaters . 14
6.2.8 Standing heat loss . 14
6.2.9 Pressure resistance . 14
6.2.10 Temperature control devices . 14
6.2.11 Heat exchanger pressure drop . 14
6.3 Production testing . 14
6.4 Factory production control (FPC) . 15
7 Technical documents . 15
7.1 General . 15
7.2 Assembly and maintenance instructions . 15
7.3 Operating instructions . 16
Annex A (normative) Hot water safety and performance testing . 17
A.1 Tests required . 17
A.2 Test apparatus and tolerances . 17
A.3 Performance tests . 19
A.4 Interpretation and calculation of hot water performance results . 21
A.5 Function of safety devices. 22
Annex B (normative) Measurement of standing heat loss for factory insulated storage
water heaters . 23
B.1 General . 23
B.2 Apparatus . 23
B.3 Test Procedure . 25
B.4 Calculation of Results . 26
Annex C (informative) Inspection access . 28
Annex ZA (informative) !Relationship between this European Standard and the
requirements of Commission Delegated Regulation (EU) No 812/2013 of 18
February 2013 supplementing Directive 2010/30/EU regarding energy labelling of
water heaters, hot water storage tanks and packages of water heater and solar
device . 30
Annex ZB (informative) !Relationship between this European Standard and the
requirements of Commission Regulation (EU) No 814/2013 of 2 August 2013
implementing Directive 2009/125/EC with regard to ecodesign requirements for
water heaters and hot water storage tanks . 32
Bibliography . 34
European foreword
This document (EN 12897:2016+A1:2020) has been prepared by Technical Committee CEN/TC 164
“Water supply”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2020, and conflicting national standards
shall be withdrawn at the latest by August 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document includes Amendment 1 approved by CEN on 2019-10-09.
This document supersedes !EN 12897:2016".
The start and finish of text introduced or altered
...
SLOVENSKI STANDARD
01-april-2020
Nadomešča:
SIST EN 12897:2016
Oskrba z vodo - Specifikacija za posredno ogrevane neprezračevane (zaprte)
akumulacijske grelnike vode
Water supply - Specification for indirectly heated unvented (closed) storage water
heaters
Wasserversorgung - Bestimmung für mittelbar beheizte, unbelüftete (geschlossene)
Speicher-Wassererwärmer
Alimentation en eau - Prescriptions pour préparateurs d'eau chaude par accumulation à
chauffage indirect non ouverts à l'air libre (fermés)
Ta slovenski standard je istoveten z: EN 12897:2016+A1:2020
ICS:
91.140.65 Oprema za ogrevanje vode Water heating equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 12897:2016+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2020
EUROPÄISCHE NORM
ICS 91.140.65
English Version
Water supply - Specification for indirectly heated
unvented (closed) storage water heaters
Alimentation en eau - Prescriptions pour préparateurs Wasserversorgung - Bestimmung für mittelbar
d'eau chaude par accumulation à chauffage indirect beheizte, unbelüftete (geschlossene) Speicher-
non ouverts à l'air libre (fermés) Wassererwärmer
This amendment A1 modifies the European Standard EN 12897:2016; it was approved by CEN on 9 October 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12897:2016+A1:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols . 8
4 Requirements . 8
4.1 Constructional requirements . 8
4.1.1 Inspection access . 8
4.1.2 Draining . 8
4.1.3 Hydraulic connections . 8
4.2 Temperature control . 9
4.3 Mechanical resistance and stability . 9
4.3.1 Pressure resistance of water storage vessel . 9
4.3.2 Pressure resistance of primary heater. 9
4.3.3 Durability . 9
4.3.4 Leakage test on double-walled primary heater . 11
4.4 Safety equipment. 11
4.4.1 General . 11
4.4.2 Energy cut-out device . 11
4.4.3 Temperature relief valve . 11
4.4.4 Pressure relief/expansion valve . 11
4.4.5 Pressure reducing valve . 11
4.4.6 Provision for expansion . 12
4.4.7 Backflow prevention . 12
5 Marking . 12
6 Evaluation of conformity . 12
6.1 General . 12
6.1.1 Compliance testing . 12
6.1.2 Market surveillance . 13
6.2 Initial type testing . 13
6.2.1 General . 13
6.2.2 Actual volume . 13
6.2.3 Rated storage volume . 13
6.2.4 Hot water volume . 13
6.2.5 Primary heating power (heat exchanger performance) . 14
6.2.6 Durability testing . 14
6.2.7 Double-walled primary heaters . 14
6.2.8 Standing heat loss . 14
6.2.9 Pressure resistance . 14
6.2.10 Temperature control devices . 14
6.2.11 Heat exchanger pressure drop . 14
6.3 Production testing . 14
6.4 Factory production control (FPC) . 15
7 Technical documents . 15
7.1 General . 15
7.2 Assembly and maintenance instructions . 15
7.3 Operating instructions . 16
Annex A (normative) Hot water safety and performance testing . 17
A.1 Tests required . 17
A.2 Test apparatus and tolerances . 17
A.3 Performance tests . 19
A.4 Interpretation and calculation of hot water performance results . 21
A.5 Function of safety devices. 22
Annex B (normative) Measurement of standing heat loss for factory insulated storage
water heaters . 23
B.1 General . 23
B.2 Apparatus . 23
B.3 Test Procedure . 25
B.4 Calculation of Results . 26
Annex C (informative) Inspection access . 28
Annex ZA (informative) !Relationship between this European Standard and the
requirements of Commission Delegated Regulation (EU) No 812/2013 of 18
February 2013 supplementing Directive 2010/30/EU regarding energy labelling of
water heaters, hot water storage tanks and packages of water heater and solar
device . 30
Annex ZB (informative) !Relationship between this European Standard and the
requirements of Commission Regulation (EU) No 814/2013 of 2 August 2013
implementing Directive 2009/125/EC with regard to ecodesign requirements for
water heaters and hot water storage tanks . 32
Bibliography . 34
European foreword
This document (EN 12897:2016+A1:2020) has been prepared by Technical Committee CEN/TC 164
“Water supply”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2020, and conflicting national standards
shall be withdrawn at the latest by August 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document includes Amendment 1 approved by CEN on 2019-10-09.
This document supersedes !EN 12897:2016".
The start and finish of text introduced or altered
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.