EN ISO 16407-2:2018

SLOVENSKI STANDARD
01-februar-2019
1DGRPHãþD
SIST-TS CEN ISO/TS 16407-2:2012
Elektronsko pobiranje pristojbin - Ugotavljanje skladnosti opreme z ISO 17575-1 -
2. del: Abstraktni preskuševalni niz (ISO 16407-2:2018)
Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-1 - Part 2:
Abstract test suite (ISO 16407-2:2018)
Elektronische Gebührenerhebung - Konformitätsbeurteilung von Einrichtungen nach ISO
17575-1 - Teil 2: Zusammengefasstes Prüfprogramm (ISO 16407-2:2018)
Perception de télépéage - Évaluation de conformité de l'équipement à l'ISO 17575-1 -
Partie 2: Suite de test abstraite (ISO 16407-2:2018)
Ta slovenski standard je istoveten z: EN ISO 16407-2:2018
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 16407-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 03.220.20; 35.240.60 Supersedes CEN ISO/TS 16407-2:2012
English Version
Electronic fee collection - Evaluation of equipment for
conformity to ISO 17575-1 - Part 2: Abstract test suite (ISO
16407-2:2018)
Perception de télépéage - Évaluation de conformité de Elektronische Gebührenerhebung -
l'équipement à l'ISO 17575-1 - Partie 2: Suite de test Konformitätsbeurteilung von Einrichtungen nach ISO
abstraite (ISO 16407-2:2018) 17575-1 - Teil 2: Zusammengefasstes Prüfprogramm
(ISO 16407-2:2018)
This European Standard was approved by CEN on 9 November 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16407-2:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 16407-2:2018) has been prepared by Technical Committee ISO/TC 204
"Intelligent transport systems" in collaboration with Technical Committee CEN/TC 278 “Intelligent
transport systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be
withdrawn at the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 16407-2:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16407-2:2018 has been approved by CEN as EN ISO 16407-2:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 16407-2
First edition
2018-11
Electronic fee collection — Evaluation
of equipment for conformity to
ISO 17575-1 —
Part 2:
Abstract test suite
Perception de télépéage — Évaluation de conformité de l'équipement
à l'ISO 17575-1 —
Partie 2: Suite de test abstraite
Reference number
ISO 16407-2:2018(E)
©
ISO 2018
ISO 16407-2:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 16407-2:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 2
5 Abstract test method (ATM) . 2
5.1 Introduction . 2
5.2 Test architecture . 2
5.2.1 Security . 3
5.3 Protocol Implementation Extra Information for Testing (PIXIT). 3
6 Untestable Test Purposes (TPs) . 3
7 ATS data structures . 4
7.1 ASN.1 description . 4
7.2 Parameterized support . 4
8 Message filtering . 6
9 ATS naming conventions. 6
9.1 Introduction . 6
9.2 Definition naming conventions . 6
9.3 Test case identifier . 7
9.4 TTCN-3 modules identifier . 8
Annex A (normative) Abstract Test Suite (ATS) for FE and BE . 9
Annex B (informative) PIXIT proforma for FE and BE .10
Bibliography .12
ISO 16407-2:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by ISO/TC 204, Intelligent transport systems.
This first edition of ISO 16407-2 cancels and replaces ISO/TS 16407-2:2012, which has been technically
revised. The following changes have been made:
— conversion from a Technical Specification to an International Standard;
— amendments to reflect changes to the underlying base standards, especially the ISO 17575 series;
— major changes regarding:
— data element changes introduced by ISO 17575-1:2016 and ISO 17575-3:2016;
— new test cases related to:
— authentication support in Charge Report;
— authentication support in Usage Statement;
— DUT responses behavior;
— removed test cases related to:
— communicatons services;
— rules with respect to support of charging which are no longer required by ISO 17575-1:2016;
— revised terms and definitions;
— editorial and formal corrections as well as changes to improve readability.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved

ISO 16407-2:2018(E)
Introduction
This document is part of a series of standards that supports interoperability of autonomous EFC-
systems. Autonomous systems use satellite positioning, often combined with additiona
...