CEN ISO/TS 17444-2:2017
(Main)Electronic fee collection - Charging performance - Part 2: Examination framework (ISO/TS 17444-2:2017)
Electronic fee collection - Charging performance - Part 2: Examination framework (ISO/TS 17444-2:2017)
ISO/TS 17444-2:2017 defines the Examination Framework for the measurement of charging performance metrics defined in ISO/TS 17444‑1 to be used during Evaluation and/or on-going Monitoring.
It specifies a method for the specification and documentation of a Specific Examination Framework which can be used by the responsible entity to evaluate charging performance for a particular information exchange interface or for overall charging performance within a Toll Scheme.
It provides a toolbox of Examination Tests for the roles of Toll Charger and Toll Service Provider for the following Scheme types:
a) DSRC Discrete;
b) Autonomous Discrete;
c) Autonomous Continuous.
The detailed choice of the set of examination tests to be used depends on the application and the respective context. Compliance with this specification is understood as using the definitions and prescriptions laid out in ISO/TS 17444-2:2017 whenever the respective system aspects are subjected to performance measurements, rather than using other definitions and examination methods than the ones specified in ISO/TS 17444-2:2017.
The following aspects are outside the scope of ISO/TS 17444-2:2017.
- ISO/TS 17444-2:2017 does not propose specific numeric performance bounds, or average or worst-case error bounds in percentage or monetary units. Those decisions are left to the Toll Charger (or to agreements between Toll Charger and Service Provider). ISO/TS 17444-2:2017 does not consider the evaluation of the expected performance of a system based on modelling and measured data from trial at another place.
- ISO/TS 17444-2:2017 does not consider the specification of a common reference system which would be required for comparison of performance between systems.
- ISO/TS 17444-2:2017 defines measurements only on standardized interfaces. Proprietary interfaces are excluded, because it is not possible to define standardized metrics on such system properties. These excluded interfaces are among others the link between Toll Charger RSE and central systems in DSRC systems, and the additional sensor input of GNSS modules (inertial sensors, CAN-bus for wheel ticks, etc.).
Elektronische Gebührenerhebung - Abbuchungsdurchführung - Teil 2: Rahmenbedingungen für Prüfungen (ISO/TS 17444-2:2017)
Perception du télépéage - Performance d'imputation - Partie 2: Cadre d'examen (ISO/TS 17444-2:2017)
Elektronsko pobiranje pristojbin - Izvajanje zaračunavanja - 2. del: Okvirni pogoji za preverjanje (ISO/TS 17444-2:2017)
Ta dokument določa meritve za uspešnost zaračunavanja sistemov za elektronsko pobiranje pristojbin (EFC) na podlagi ravni napak, povezanih z izračuni zaračunavanja.
Ta dokument je osnovni standard meritev. Podrobna izbira meritev je odvisna od uporabe in povezanega konteksta.
Ta dokument opisuje sklop meritev z ustreznimi opredelitvami, načeli in ubeseditvami, ki skupaj sestavljajo referenčni okvir za določitev zahtev za sisteme za elektronsko pobiranje pristojbin
ter poznejši pregled njihove uspešnosti zaračunavanja.
Meritve uspešnosti zaračunavanja iz tega dokumenta so namenjene uporabi v zvezi s katerim koli sistemom zaračunavanja, ne glede na njegovo tehnično zasnovo, sistemsko arhitekturo, tarifno strukturo, geografsko pokritost ali organizacijski model. Določijo se za obravnavanje tehničnih podrobnosti, ki se lahko razlikujejo med tehnologijami in ponudniki ali se sčasoma spreminjajo kot »črna skrinjica«.
Osredotočajo se izključno na rezultat postopka zaračunavanja, tj. na znesek, ki se zaračuna glede na vnaprej izmerjen
ali teoretično pravilen znesek, in ne na vmesne spremenljivke, ki izhajajo iz različnih sestavnih delov
senzorjev, kot je položajna natančnost, doseg signala ali optična ločljivost. Ta pristop zagotavlja
primerljive rezultate za vsako meritev v vseh ustreznih primerih.
Meritve so namenjene obravnavanju informacij, izmenjanih v okviru čelnega vmesnika in
vmesnikov interoperabilnosti med izvajalci storitev cestninjenja, pobiralci cestnine in uporabniki cest ter tudi na
celotni ravni.
Opredeljene so meritve v zvezi z naslednjimi izmenjavami informacij:
– poročila o zaračunavanju,
– izjave o plačilu cestnine,
– podatki o obračunavanju in povezani podatki o dogodku,
– zahtevki za plačilo na ravni uporabniških računov storitve pobiranja cestnin,
– uporabniški računi,
– celotne meritve, ki ocenijo splošno delovanje postopka zaračunavanja.
Podrobnosti o utemeljitvi te izbire so navedene v točki 5.1.
Predlagane meritve so posebej namenjene zaščiti interesov udeležencev v sistemu cestninjenja,
kot so izvajalci storitev cestninjenja, pobiralci cestnine in uporabniki cest. Meritve je mogoče uporabiti za opredelitev
zahtev (npr. za zahteve za predloge) in ocenjevanje uspešnosti.
Ta dokument določa dve vrsti primerov, v katerih je potrebna ocena uspešnosti:
a) kadar se ocena izvaja v omejenem časovnem obdobju, na primer pri oblikovanju
zahtev in oceni sistemov za namene pridobivanja in preskušanje ustreznosti,
pri čemer se te vrste ocene imenujejo vrednotenje,
b) kadar je ocena potrebna v okviru stalnega nadzornega postopka v celotni življenjski dobi
sistema, da se validirajo ravni pogodbene storitve, opredeli goljufija ali okvara ali
podprejo stalni postopki vzdrževanja in izboljšave uspešnosti. Ta vrsta ocene se
imenuje spremljanje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2018
1DGRPHãþD
SIST-TS CEN ISO/TS 17444-2:2014
(OHNWURQVNRSRELUDQMHSULVWRMELQ,]YDMDQMH]DUDþXQDYDQMDGHO 2NYLUQLSRJRML
]DSUHYHUMDQMH ,6276
Electronic fee collection - Charging performance - Part 2: Examination framework
(ISO/TS 17444-2:2017)
Elektronische Gebührenerhebung - Abbuchungsdurchführung - Teil 2:
Rahmenbedingungen für Prüfungen (ISO/TS 17444-2:2017)
Perception du télépéage - Performance d'imputation - Partie 2: Cadre d'examen (ISO/TS
17444-2:2017)
Ta slovenski standard je istoveten z: CEN ISO/TS 17444-2:2017
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN ISO/TS 17444-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
November 2017
TECHNISCHE SPEZIFIKATION
ICS 03.220.20; 35.240.60 Supersedes CEN ISO/TS 17444-2:2013
English Version
Electronic fee collection - Charging performance - Part 2:
Examination framework (ISO/TS 17444-2:2017)
Perception du télépéage - Performance d'imputation - Elektronische Gebührenerhebung -
Partie 2: Cadre d'examen (ISO/TS 17444-2:2017) Abbuchungsdurchführung - Teil 2:
Rahmenbedingungen für Prüfungen (ISO/TS 17444-
2:2017)
This Technical Specification (CEN/TS) was approved by CEN on 27 August 2017 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 17444-2:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (CEN ISO/TS 17444-2:2017) has been prepared by Technical Committee ISO/TC 204
“Intelligent transport systems” in collaboration with Technical Committee CEN/TC 278 “Intelligent
transport systems” the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 17444-2:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO/TS 17444-2:2017 has been approved by CEN as CEN ISO/TS 17444-2:2017 without any
modification.
TECHNICAL ISO/TS
SPECIFICATION 17444-2
Second edition
2017-09
Electronic fee collection — Charging
performance —
Part 2:
Examination framework
Perception du télépéage — Performance d'imputation —
Partie 2: Cadre d'examen
Reference number
ISO/TS 17444-2:2017(E)
©
ISO 2017
ISO/TS 17444-2:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO/TS 17444-2:2017(E)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 6
5 Examination Framework . 7
5.1 General . 7
5.2 Method for defining a Specific Examination Framework . 8
5.2.1 General. 8
5.2.2 Selection of metrics to be evaluated . 9
5.2.3 Definition of environmental conditions and associated
performance requirements . . 9
5.2.4 Determination of Required Sample Sizes . 9
5.2.5 Selection of methods for generating Charging Input and Reference Data .10
5.2.6 Determination of Test Routes/Subset of Charged Network for generating
representative trips .10
5.2.7 Documentation of the Specific Examination Framework .10
5.3 Sources of data .10
5.4 Methods of generating charging input .13
5.4.1 General.13
5.4.2 Predefined routes (identifier: “PVP”) .14
5.4.3 Reference System (used in combination with identifiers: “PVR” and “UVR”) .15
5.4.4 Simulated OBE/FE (identifier: “SO”) .16
5.4.5 Dedicated OBE Testing (identifier: “DO”) .17
5.5 Applicability of metrics scheme types .17
5.6 Charging Metric Selection Tables .22
5.6.1 General.22
5.6.2 DSRC Discrete .22
5.6.3 Autonomous Discrete .23
5.6.4 Autonomous Continuous .24
6 Examination Tests .26
6.1 Common (and DSRC Discrete) Examination Tests .26
6.1.1 General.26
6.1.2 ET-CM-E2E-1 E2E — Correct Charging Rate .26
6.1.3 ET-CM-E2E-2 E2E — Overcharging Rate .27
6.1.4 ET-CM-E2E-3 E2E — Undercharging Rate.27
6.1.5 ET-CM-E2E-4 E2E — Late Charging Rate .28
6.1.6 ET-CM-UA-1 UA — Correct Charging Rate .29
6.1.7 ET-CM-UA-2 UA — Overcharging Rate .29
6.1.8 ET-CM-UA-3 UA — Undercharging Rate .30
6.1.9 ET-CM-UA-4 UA — Accurate application of Payments and Refunds .31
6.1.10 ET-CM-UA-5 UA — Accurate Personalisation of OBUs .31
6.1.11 ET-CM-PC-1 PC — Correct Charging Rate .32
6.1.12 ET-CM-PC-2 PC — Overcharging Rate .32
6.1.13 ET-CM-PC-3 PC — Undercharging Rate .33
6.1.14 ET-CM-PC-4 PC — Latency — TC .34
6.1.15 ET-CM-PC-5 PC — Late Payment Claims Rate .34
6.1.16 ET-CM-PC-6 PC — Rejected Payment Claim Rate .35
6.1.17 ET-CM-BD-1 BD — Correct Charging Rate.35
6.1.18 ET-CM-BD-2 BD — Overcharging Rate .36
6.1.19 ET-CM-BD-3 BD — Undercharging Rate .37
ISO/TS 17444-2:2017(E)
6.1.20 ET-CM-BD-4 BD — Incorrect Charging Rate .37
6.1.21 ET-CM-BD-5 BD — Latency — TC .38
6.1.22 ET-CM-BD-6 BD — Late Billing Details Rate .38
6.1.23 ET-CM-BD-7 BD — Rejected
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.