EN ISO 7010:2020/A7:2024
(Amendment)Graphical symbols - Safety colours and safety signs - Registered safety signs - Amendment 7 (ISO 7010:2019/Amd 7:2023)
Graphical symbols - Safety colours and safety signs - Registered safety signs - Amendment 7 (ISO 7010:2019/Amd 7:2023)
Graphische Symbole - Sicherheitsfarben und Sicherheitszeichen - Registrierte Sicherheitszeichen - Änderung 7 (ISO 7010:2019/Amd 7:2023)
Symboles graphiques - Couleurs de sécurité et signaux de sécurité - Signaux de sécurité enregistrés - Amendement 7 (ISO 7010:2019/Amd 7:2023)
Grafični simboli - Varnostne barve in varnostni znaki - Registrirani varnostni znaki - Dopolnilo 7 (ISO 7010:2019/Amd 7:2023)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Grafični simboli - Varnostne barve in varnostni znaki - Registrirani varnostni znaki
- Dopolnilo 7 (ISO 7010:2019/Amd 7:2023)
Graphical symbols - Safety colours and safety signs - Registered safety signs -
Amendment 7 (ISO 7010:2019/Amd 7:2023)
Symboles graphiques - Couleurs de sécurité et signaux de sécurité - Signaux de sécurité
enregistrés - Amendement 7 (ISO 7010:2019/Amd 7:2023)
Ta slovenski standard je istoveten z: EN ISO 7010:2020/prA7
ICS:
01.080.10 Simboli za javno obveščanje. Public information symbols.
Znaki. Table. Označbe Signs. Plates. Labels
13.200 Preprečevanje nesreč in Accident and disaster control
katastrof
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 7010
Third edition
2019-07
AMENDMENT 7
2023-07
Graphical symbols — Safety colours
and safety signs — Registered safety
signs
AMENDMENT 7
Symboles graphiques — Couleurs de sécurité et signaux de sécurité —
Signaux de sécurité enregistrés
AMENDEMENT 7
Reference number
ISO 7010:2019/Amd.7:2023(E)
ISO 7010:2019/Amd.7:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 7010:2019/Amd.7:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.