iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14879-4:2007

(Main)

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components

This document describes the requirements for and methods of testing of organic linings which are applied to metallic process engineering equipment that will come in contact with chemical substances. The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract
partners )).
The standard applies to linings which serve one or more of the following purposes:
   to protect the component from adverse effects of aggressive substances;
   to protect waters (e.g. ground water) from harmful substances;
   to protect the charge from becoming contaminated by components released from the substrate material;
   to achieve a particular surface quality.
This standard applies to vessels, apparatus, piping parts and other components for process plants made of metallic substrate materials which are in contact with media and are provided with a surface protection made of
a)   prefabricated, natural or synthetic rubber based sheeting (subsequently named rubber lining), to be
applied in the workshop or on site;
b)   prefabricated, phenol formaldehyde or epoxy resin based sheeting (subsequently named duroplastic lining), to be applied in the workshop only;
c)   prefabricated, thermoplastic products (e.g. foils, sheeting, plates, pipes) (subsequently named thermoplastic lining), to be applied in the workshop or on site.
The standard specifies the requirements, acceptance inspection, packaging, transport, storage and installation of organic linings for metallic materials.
The tests described in this standard are intended for verification of the suitability of sheeting used for linings and for acceptance inspection to be carried out on the products during or after application of the lining or as part of routine inspections to determine any changes effected in the lining during service.

Beschichtungen und Auskleidungen aus organischen Werkstoffen zum Schutz von industriellen Anlagen gegen Korrosion durch aggressive Medien - Teil 4: Auskleidungen für Bauteile aus metallischen Werkstoffen

Systèmes de revêtements organiques de peinture et autres revêtements rapportés pour la protection des appareils et installations industriels contre la corrosion par des fluides agressifs - Partie 4 : Revêtements rapportés sur composant métallique

Le présent document décrit les exigences et méthodes d’essai pour revêtements rapportés organiques appliqués sur des équipements métalliques de l’industrie, entrant au contact de substances chimiques. Les exigences spécifiées dans la présente norme peuvent être utilisées aux fins de contrôle qualité notamment, comme convenu entre les parties contractantes ).
La présente norme est applicable aux revêtements rapportés destinés à l’un au moins des usages suivants :
   protéger le composant contre les effets néfastes des substances corrosives ;
   protéger les eaux (par exemple, les nappes phréatiques) des substances dangereuses ;
   protéger le contenu de l’appareil contre la contamination par des composants provenant des matériaux du subjectile ;
   obtenir une qualité de surface spécifique.
La présente norme est applicable aux récipients, appareils, éléments de tuyauterie et autres composants d’installations industrielles constituant des subjectiles métalliques entrant en contact de milieux et dotés d’une protection de surface composée de :
a)   revêtement de caoutchouc naturel ou synthétique préfabriqué (dénommé ci-après revêtement rapporté de caoutchouc), à appliquer en atelier ou sur site ;
b)   revêtement préfabriqué à base de résines phénol-formaldéhyde ou époxy (dénommé ci-après revêtement rapporté thermodurcissable), à appliquer uniquement en atelier ;
c)   produits thermoplastiques préfabriqués (feuilles, revêtement, plaques, tuyaux, par exemple) (dénommés ci-après revêtement rapporté thermoplastique), applicables en atelier ou sur site.
La présente norme spécifie les exigences, l’inspection de réception, l’emballage, le transport, le stockage et l’installation des revêtements rapportés organiques pour les matériaux métalliques.

Sistemi organskih premazov in prevlek za protikorozijsko zaščito industrijskih naprav in obratov v kemijsko agresivnih pogojih - 4. del: Prevleke na kovinskih delih

General Information

Status
Published
Publication Date
31-Jul-2007
Withdrawal Date
28-Feb-2008
ICS
25.220.60 - Organic coatings
Technical Committee
CEN/TC 360 - Project Committee - Coating systems for chemical apparatus and plants against corrosion
Drafting Committee
CEN/TC 360 - Project Committee - Coating systems for chemical apparatus and plants against corrosion
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
04-Mar-2018
Completion Date
04-Mar-2018
Ref Project
SIST EN 14879-4:2009 - Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components

Buy Standard

EN 14879-4:2009EN 14879-4:2009
PreviousNext
Standard
EN 14879-4:2009
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LQGXVWULMVNLKGHOLKBeschichtungen und Auskleidungen aus organischen Werkstoffen zum Schutz von industriellen Anlagen gegen Korrosion durch aggressive Medien - Teil 4: Auskleidungen für Bauteile aus metallischen WerkstoffenSystemes de revetements organiques de peinture et autres revetements rapportés pour la protection des appareils et installations industriels contre la corrosion par des milieux agressifs - Partie 4: Revetements rapportés pour composants métalliquesOrganic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components25.220.60Organske prevlekeOrganic coatingsICS:Ta slovenski standard je istoveten z:EN 14879-4:2007SIST EN 14879-4:2009en,fr,de01-januar-2009SIST EN 14879-4:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14879-4August 2007ICS 25.220.60 English VersionOrganic coating systems and linings for protection of industrialapparatus and plants against corrosion caused by aggressivemedia - Part 4: Linings on metallic componentsSystèmes de revêtements organiques de peinture et autresrevêtements rapportés pour la protection des appareils etinstallations industriels contre la corrosion par des milieuxagressifs - Partie 4: Revêtements rapportés pourcomposants métalliquesBeschichtungen und Auskleidungen aus organischenWerkstoffen zum Schutz von industriellen Anlagen gegenKorrosion durch aggressive Medien - Teil 4: Auskleidungenfür Bauteile aus metallischen WerkstoffenThis European Standard was approved by CEN on 24 June 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14879-4:2007: ESIST EN 14879-4:2009

Material combinations to which the media lists for rubber linings
are applicable.29 B.1 Hard rubber linings (media list I).29 B.2 Soft rubber linings.29 B.2.1 Butyl rubber, halogenated butyl rubber (media list II).29 B.2.2 Chloroprene rubber (media list III).29 B.3 Test media for the media lists.29 B.3.1 General.29 B.3.2 Media lists.30 Annex C (normative)
Test fluid groups for verification of suitability for material/media
combinations.32 Annex D (normative)
Testing the dissipating capability.35 D.1 Principle.35 D.1.1 Dissipation resistance.35 D.1.2 Dissipation resistance to earth.35 D.2 Testing of dissipation resistance of test samples.35 D.2.1 Test equipment.35 D.2.2 Test procedure.35 D.2.3 Test report.36 D.3 Measurement of dissipation resistance to earth on the completely applied lining.36 D.3.1 Test equipment.36 D.3.2 Preparation of the lining.36 D.3.3 Procedure.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 14879-6:2009(Main)
Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 6: Combined linings with tile and brick layers
SIST EN 14879-6:2010

This European Standard describes the requirements for and methods of testing of combined systems with tile and brick layers which are applied to concrete or metallic process engineering equipment that will come in contact with chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners or having been given by national regulations )).
The standard applies to systems which serve one or more of the following purposes:
-   to protect the component from adverse effects of aggressive substances;
-   to protect waters (e.g. ground water) against hazardous substances;
-   to protect the charge from becoming contaminated by components released from the substrate material;
-   to achieve a particular surface quality.
The described combined systems can be used for concrete or metallic process engineering equipment that will come into contact with chemical substances.
The combined system is a combination of:
-   a coating according to EN 14879-2 or EN 14879-3 with an additional layer of tiles or bricks embedded in cement mortar, resin based mortar and/or potassium silicate mortar as an adhesive bonding cement (re-ferred to simply as cement in this standard); or
-   a lining according to EN 14879-4 or EN 14879-5 with an additional layer of tiles or bricks embedded in cement mortar, resin based mortar and/or potassium silicate mortar as an adhesive bonding cement (re-ferred to simply as cement in this standard).
For design and preparation of substrate, see EN 14879-1.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14879-5:2007(Main)
Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components
SIST EN 14879-5:2009

This document describes the requirements for and methods of testing of organic linings which are applied to concrete process engineering equipment that will come in contact with aggressive chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners).
The standard applies to linings which serve one or more of the following purposes:
   to protect the component from damaging effects of aggressive substances;
   to protect waters (e.g. ground water) from harmful substances;
   to protect the charge from becoming contaminated by components released from the substrate material;
   to achieve a particular surface quality.
The different lining systems are:
a)   bonded linings;
b)   mechanically fixed linings;
c)   loose linings of sheeting material;
d)   loose linings of pre-formed pieces or lining units.
Handling of aggressive or water pollutant materials is understood to include
e)   storage;
f)   filling;
g)   loading and unloading;
h)   manufacture;
i)   treatment;
j)   use.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14879-2:2006(Main)
Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components
SIST EN 14879-2:2007

This European Standard specifies the requirements for and methods of testing of organic coatings which are applied to metallic process engineering equipment that will come in contact with chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners or been given by national regulations).
The standard does not cover coatings as in EN ISO 12944-1, but it does apply to coatings which serve one or more of the following purposes:
-   to protect the component from adverse effects of aggressive substances;
-   to protect waters (e.g. ground water) against hazardous substances;
-   to protect the charge from becoming contaminated by components released from the substrate material;
-   to achieve a particular surface properties.
The described coatings are to be used for metallic process engineering equipment that will come in contact with chemical substances. The different coating systems are:
-   laminate coating systems which contain cold-curing resins;
-   trowelled coating which contain cold-curing resins;
-   sprayed coating systems which contain resins (in special cases, such coatings may also be applied by brushing, rolling, flow coating, dipping, or by other means, such as providing sleeving for nozzles);
-   powder coating systems which contain organic materials (powder coatings may be used as corrosion protection or for non-stick purposes).
For design and preparation of substrate see EN 14879-1.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14879-3:2006(Main)
Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 3: Coatings on concrete components
SIST EN 14879-3:2007

This European Standard specifies the requirements for and methods of testing of organic coatings which are applied to concrete process engineering equipment that will come in contact with aggressive chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners).
The standard does not cover coatings as in EN ISO 12944-1, but it does apply to coatings which serve one or more of the following purposes:
-   to protect the component from damaging effects of aggressive substances;
-   to protect waters (e.g. ground water) from harmful substances;
-   to protect the charge from becoming contaminated by components released from the substrate material;
-   to achieve a particular surface properties.
The different coating systems are:
a)   impregnation, seals, thin coatings (applied by brushing, spraying or rolling);
b)   high-build coatings (applied by brushing, spraying, rolling, trowelling or pouring (self-levelling));
c)   laminate coatings;
d)   resinous screed;
e)   mastic asphalt screed with a waterproofing layer;
f)   combinations of the above coatings.
Table 1 shows the coating methods to be employed for various types of concrete members.
Handling of aggressive or water pollutant materials is understood to include:
storage;
1)   filling;
2)   loading and unloading;
3)   manufacture;
4)   treatment;
5)   use.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14879-1:2005(Main)
Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 1: Terminology, design and preparation of substrate
SIST EN 14879-1:2005

This European Standard describes the terminology, the design and the preparation of the substrate of
industrial apparatus for the protection against corrosion caused by aggressive media. These industrial apparatus include, for example, reaction tanks, storage tanks, floors in industrial plants, in general for production and handling of chemicals.
The protection is applicable to metallic and concrete structures.
Beside the protection of the apparatus, the protection of the media itself against pollution is also considered in this series of European Standards EN 14879.
A protection against corrosion caused by atmospheric exposure (as for example according to EN ISO 12944-4) is not included in the scope of this series of European Standards EN 14879.
Corrosion protection systems according to this series of European Standards EN 14879 are:
1)  Thick coatings normally of 1 mm or more thick.
2)  Linings made of pre-fabricated sheets respectively plate materials.
3)  Combined linings with tile and brick layers.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-10:2024(Main)
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation
SIST EN 13523-10:2024

This part of the EN 13523 series specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-1:2024(Main)
Coil coated metals - Test methods - Part 1: Film thickness
SIST EN 13523-1:2024

This document specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Five appropriate methods are given in this document:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical;
e)   ruggedized optical interference.
The methods are applicable only to products with smooth and flat substrates, but the coating itself can be textured. In that case, for methods a) and b), the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness, method d) can provide the minimum, maximum and average thickness, and e) will give the total thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness are only applicable on method a).

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-3:2024(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
SIST EN 13523-3:2024

This document specifies procedures for determining the instrumental colour difference (CIELAB   or  ) of an organic coating on a metallic substrate compared to another one used as a reference (usually called reference) and the metamerism depending on the illuminant.
When two colour specimens have identical spectral reflectance curves, they are matching under any illuminant irrespective of its spectral characteristics. This is termed a “spectral match”. It is also possible for two colour specimens having different spectral reflectance curves to match visually under a given light source but not to match under another light source with different spectral characteristics; such matches are termed "metameric".
One quantitative description of metamerism is the so-called "metamerism index".
Information on the metamerism index is of limited value where ΔE (instrumental colour difference for a given illuminant) is > 0,5. The metamerism index is not suited for determining the absolute colour difference or colour consistency of a given specimen at change of illuminant.
The colour difference under the reference illuminant is to be measured in colour coordinates L*, a* and b*.
Excluded from this method are organic coatings producing fluorescence and/or which are multicoloured, pearlescent or metallic.
Establishing a reference as well as the magnitude of an acceptable colour difference are not covered by this method.
Two methods are given in this document:
a)   instrumental colour difference measurement using a tristimulus colourimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
It is advised that care is taken when measuring e.g.
-   textured surfaces;
-   fluorescent coatings;
-   metameric coatings;
-   multi-coloured, pearlescent, metallic or special colour effect coatings.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-22:2024(Main)
Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison
SIST EN 13523-22:2024

This document specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth.
NOTE   Results can differ between natural and artificial daylight.
It might be that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523 3).
If a metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) can be made, in accordance with EN 13523 3.
No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure is only intended to be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.).
The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-29:2024(Main)
Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
SIST EN 13523-29:2024

This part of the EN 13523 series specifies a procedure for the comparative evaluation of resistance to soiling of an organic coating on a metallic substrate (coil coating) in an outdoor exposure environment, particularly the soiling defect known as "Tiger stripes".

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day