EN 1218-5:2004/prA1

SLOVENSKI STANDARD
01-april-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
(QRVWUDQVNLSURILOQLVWURML]QHSRPLþQRPL]RLQSRGDMDOQLPLYDOMLDOLYHULåQLP
SRGDMDQMHP
Safety of woodworking machines - Tenoning machines - Part 5: One side profiling
machines with fixed table and feed rollers or feed chain
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 5: Einseitige Profiliermaschinen mit festem Tisch und mit Vorschubrollen oder mit
Kettenbandvorschub
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 5: Machines à
profiler sur une face à table fixe et avance par rouleaux ou par chaîne
Ta slovenski standard je istoveten z: EN 1218-5:2004/prA1
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 1218-5:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Tenoning machines - Part 5:
One side profiling machines with fixed table and feed rollers or
feed chain
Sécurité des machines pour le travail du bois - Sicherheit von Holzbearbeitungsmaschinen -
Tenonneuses - Partie 5: Machines à profiler sur une face à Zapfenschneid- und Schlitzmaschinen - Teil 5: Einseitige
table fixe et avance par rouleaux ou par chaîne Profiliermaschinen mit festem Tisch und mit Vorschubrollen
oder mit Kettenbandvorschub
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1218-5:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-5:2004/prA1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to the title page .4
2 Modification to the Foreword .4
3 Modification to Clause 1, Scope .4
4 Modification to Clause 2, Normative references .4
5 Modification to 3.3, Definitions .5
6 Modification to Clause 4, List of significant hazards .5
7 Modification to 5.2.1, Safety and reliability of control systems .7
8 Modification to 5.2.3, Starting .8
9 Modification to 5.2.4, Normal stopping .8
10 Modification to 5.2.5, Emergency stop .8
11 Modification to 5.2.8, Speed changing .8
12 Modification to 5.2.9, Failure of the power supply .8
13 Modification to 5.2.10, Failure of control circuits .8
14 Modification to 5.3.2, Hazard resulting from break-up.8
15 Modification to 5.3.3.2, Strength .8
16 Modification to 5.3.3.6, Spindle rings .9
17 Modification to 5.3.5, Devices to minimise the possibility or the effect of ejection .9
18 Modification to 5.4.1, Fire .9
19 Modification to 5.4.4, Electricity .9
20 Modification to 5.4.5, Ergonomics and handling .9
21 Modification to 5.4.6, Lighting . 10
22 Modification to 5.4.9, Radiation . 10
23 Modification to 5.4.12, Isolation . 10
24 Modification to 5.4.13, Maintenance . 10
25 Modification to 6.2, Marking . 10
26 Modification to 6.3, Instruction handbook . 11
27 Modification to Annex A . 12
28 Modification to Annex D . 12
29 Modification to Annex ZA . 12
30 Addition of Annex ZB . 13
31 Modification to the Bibliography . 14

Foreword
This document (EN 1218-5:2004/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the title page
In the third element of the English title page, replace "fed by" with "feed".
2 Modification to the Foreword
Replace the fourth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
3 Modification to Clause 1, Scope
Replace first paragraph with the following: "This document specifies the significant hazards, hazardous
situations and events as listed in Clause 4 which are relevant to one side profiling machines with fixed table
and feed rollers or feed chain hereinafter referred to as "machines", where the loading and unloading is
manual and where the maximum work-piece height capacity is 200 mm. The machine is designed to process
in one pass one side of solid wood, chip board, fibreboard or plywood and also these materials where they are
covered with plastic laminate. The work-piece is fed through the processing units by an integrated feed
consisting of rollers or a chain.".
Delete the second paragraph.
4 Modification to Clause 2, Normative references
Delete all full stops at the end of reference titles.
Delete reference to EN 294:1992.
Delete reference to EN 418:1992 and add: "EN ISO 13850:2008, Safety of machinery — Emergency stop —
st
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.2.5, 1 paragraph, with
"EN ISO 13850".
Delete reference to EN 954-1:1996 and add:"EN ISO 13849-1:2008, Safety of machinery — Safety-related
parts of control systems — Part 1: General principles for design (ISO 13849-1:2006)" and replace "EN 954-
1:1996" with "EN ISO 13849-1:2008" throughout the document.
Replace "EN 847-1:1997" with "EN 847-1:2005" throughout the document.
Replace "EN 60204-1:1992" with "EN 60204-1:2006" and replace in the title
"(IEC 60204-1:1992, modified)" with "(IEC 60204-1:2005, modified)".
Replace "EN 60947-4-1:1992" with "EN 60947-4-1:2001" throughout the document and replace in the title
"(IEC 60947-4-1:1990)" with "(IEC 60947-4-1:2000)".
Replace "EN 60947-5-1:1997" with "EN 60947-5-1:2004" throughout the document and replace in the title
"(IEC 60947-5-1:1990)" with "(IEC 60947-5-1:2003)".
Replace reference to "HD 21.1 S3:1997" with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace
"HD 21.1 S3:1997" with "HD 21.1 S4:2002" throughout the document.
Replace reference to "HD 22.1 S3:1997" with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace
"HD 22.1 S3:1997" with "HD 22.1 S4:2002" throughout the document.
Add the following references:
"EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles",
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery",
"EN 50370-1:2005, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 1: Emission
EN 50370-2:2003, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 2: Immunity",
"EN 60439-1:1999, Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially
type-tested assemblies (IEC 60439-1:1999)",
"EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, auditory and tactile signals (IEC 61310-1:2007)".
5 Modification to 3.3, Definitions
Definition 3.3.12, replace the term with "displaceable machine".
Definition 3.3.13, replace the term with "information from the supplier".
6 Modification to Clause 4, List of significant hazards
Replace the clause content with the following:
"This clause contains the significant hazards, hazardous situations and events (see EN 1050:1996) as far as
they are dealt with in this document, identified by risk assessment as significant for the machines as defined in
the scope and which require action to eliminate or reduce the risk. This document deals with these significant
hazards by defining safety requirements and/or measures or by reference to relevant standards.
These hazards are listed in Table 1 in accordance with Annex A of EN 1050:1996.
Table 1 — List of significant hazards
Hazards, hazardous situations and Relevant sub-
No hazardous events EN ISO 12100 clause of this
document
Part 1: Part 2:
2003 2003
1 Mechanical hazards related to:
- machine parts or workpieces:
a) shape; 4.2 4.2.1, 5.3.3, 5.3.5,
4.2.2, 5 5.3.6, 5.3.7,
5.4.2, 5.4.5
b) relative location; 5.2.2, 5.2.5,
5.3.3, 5.3.7
d) mass and velocity (kinetic energy of 5.2.6, 5.2.7
elements in controlled or uncontrolled
motion);
e) mechanical strength. 5.3.2, 5.3.3,
5.3.5
- accumulation of energy inside the machinery:
g) liquids and gases under pressure; 4.2 4.10, 5.5.4 5.4.7, 5.4 8
1.1
...