EN ISO 3262-9:2023

SLOVENSKI STANDARD
01-oktober-2023
Nadomešča:
SIST EN ISO 3262-9:1998
Polnila - Specifikacije in preskusne metode - 9. del: Kalciniran kaolin (ISO 3262-
9:2023)
Extenders - Specifications and methods of test - Part 9: Calcined clay (ISO 3262-9:2023)
Füllstoffe - Anforderungen und Prüfverfahren - Teil 9: Calcinierter Kaolin (ISO 3262-
9:2023)
Matières de charge - Spécifications et méthodes d’essai - Partie 9: Argile calcinée (ISO
3262-9:2023)
Ta slovenski standard je istoveten z: EN ISO 3262-9:2023
ICS:
87.060.10 Pigmenti in polnila Pigments and extenders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 3262-9
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2023
EUROPÄISCHE NORM
ICS 87.060.10 Supersedes EN ISO 3262-9:1998
English Version
Extenders - Specifications and methods of test - Part 9:
Calcined clay (ISO 3262-9:2023)
Matières de charge - Spécifications et méthodes d'essai Füllstoffe - Anforderungen und Prüfverfahren - Teil 9:
- Partie 9: Argile calcinée (ISO 3262-9:2023) Calcinierter Kaolin (ISO 3262-9:2023)
This European Standard was approved by CEN on 1 July 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3262-9:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 3262-9:2023) has been prepared by Technical Committee ISO/TC 256
"Pigments, dyestuffs and extenders" in collaboration with Technical Committee CEN/TC 298 “Pigments
and extenders” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2024, and conflicting national standards shall
be withdrawn at the latest by January 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3262-9:1998.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 3262-9:2023 has been approved by CEN as EN ISO 3262-9:2023 without any
modification.
INTERNATIONAL ISO
STANDARD 3262-9
Second edition
2023-07
Extenders — Specifications and
methods of test —
Part 9:
Calcined clay
Matières de charge — Spécifications et méthodes d’essai —
Partie 9: Argile calcinée
Reference number
ISO 3262-9:2023(E)
ISO 3262-9:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 3262-9:2023(E)
Contents  Page
Foreword .iv
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Requirements and test methods . 2
5  Sampling . 2
6  Determination of the particle size distribution . 3
6.1 General . 3
6.2 Principle . 3
6.3 Reagents . 3
6.3.1 Dispersing agent . 3
6.4 Apparatus . 3
6.5 Preparation for the test . 5
6.5.1 Calibration of pipette. 5
6.5.2 Calibration of sedimentation vessel . 5
6.6 Procedure . 5
6.6.1 Number of determinations . 5
6.6.2 Test portion . 5
6.6.3 Sedimentation . 5
6.6.4 Calculation of withdrawal time. 6
6.7 Calculation of cumulative percentage undersize . 6
6.8 Acceptance of test values . 6
6.9 Expression of results . . 7
7  Test report . 7
Bibliography . 8
iii
ISO 3262-9:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 256, Pigments, dyestuffs and extenders, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC
298, Pigments and extenders, in accordance with the Agreement on technical cooperation between ISO
and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 3262-9:1997), which has been technically
revised.
The main changes are as follows:
— the first part of the title has been changed to “Extenders”;
— alkaline fusion has been added in Table 1 as a second method for determination of the aluminium
silicate content;
— the test method for particle size distribution in Table 2 has been changed to ISO 8130-13;
— the normative references have been updated.
A list of all parts in the ISO 3262 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 3262-9:2023(E)
Extenders — Specifications and methods of test —
Part 9:
Calcined clay
1  Scope
This document specifies requirements and corresponding methods of test for calcined clay.
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only t
...