iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12697-1:2000

(Main)

Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content

Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content

This European Standard describes test methods for the determination of the soluble binder content of samples of bituminous mixtures. The test methods described are suitable for quality control purposes during the production of plant mix and for checking compliance with a product specification. Test methods for the analysis of mixtures containing modified binders are outside the scope of this European Standard.

Asphalt - Prüfverfahren für Heißasphalt - Teil 1: Löslicher Bindemittelgehalt

Diese Europäische Norm beschreibt Prüfverfahren zur Bestimmung des Bindemittelgehaltes in Proben aus Asphalt. Die beschriebenen Prüfverfahren sind zur Qualitätskontrolle während der Herstellung des Mischgutes sowie zur Überprüfung der Übereinstimmung mit einer Produktanforderung geeignet. Prüfverfahren zur Untersuchung von Mischgut, das modifiziertes Bindemittel enthält, gehören nicht zum Anwendungsbereich dieser Europäischen Norm.

Mélanges bitumineux - Essais pour enrobés à chaud - Teneur en bitume

La présente Norme Européenne décrit les modes opératoires à suivre pour déterminer la teneur en liant des échantillons de mélanges bitumineux. Les méthodes d'essai décrites sont adaptées au contrôle qualité en cours de production d'un mélange d'usine et à la vérification de la conformité à une spécification produit. Les méthodes d'essai correspondant à l'analyse de mélanges contenant des liants modifiés sont hors de propos dans cette Norme Européenne.

Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content

General Information

Status
Withdrawn
Publication Date
17-Oct-2000
Withdrawal Date
22-Nov-2005
ICS
93.080.20 - Road construction materials
Technical Committee
CEN/TC 227 - Road materials
Drafting Committee
CEN/TC 227/WG 1 - Bituminous mixtures
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
23-Nov-2005
Completion Date
23-Nov-2005
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/124 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on road construction products
Ref Project
SIST EN 12697-1:2002 - Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content

Relations

Corrected By
EN 12697-1:2000/AC:2001 - Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content
Effective Date
22-Dec-2008
Replaced By
EN 12697-1:2005 - Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content
Effective Date
22-Dec-2008

Buy Standard

EN 12697-1:2002EN 12697-1:2002
PreviousNext
Standard
EN 12697-1:2002
English language
49 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder contentAsphalt - Prüfverfahren für Heißasphalt - Teil 1: Löslicher BindemittelgehaltMélanges bitumineux - Essais pour enrobés a chaud - Teneur en bitumeBituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-1:2000SIST EN 12697-1:2002en01-september-2002SIST EN 12697-1:2002SLOVENSKI
STANDARD



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002



SIST EN 12697-1:2002
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12697-4:2023(Main)
Bituminous mixtures - Test methods - Part 4: Bitumen recovery: Fractionating column
SIST EN 12697-4:2023

This document specifies a method for the recovery of soluble bitumen from bituminous mixtures used in road, airfield or similar pavements in a form suitable for further testing.
The method is applicable for the recovery of paving grade bitumen and is the reference method for recovery of soluble bitumen from bituminous mixtures containing volatile matter such as cut-back bitumen.
The method is not applicable for recovery of polymer-modified bitumen.
NOTE   EN 12697-3 is the reference method for the recovery of paving grade bitumen and polymer-modified bitumen.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-43:2023(Main)
Bituminous mixtures - Test methods - Part 43: Resistance to fuel
SIST EN 12697-43:2023

This document specifies a test method to determine the resistance of a bituminous mixture or pavement to fuels. The procedure involves initial soaking of a test specimen made in the laboratory or cored from a pavement in a fuel, followed by a brushing period with a brush test device. The material loss of the specimen is a measure of the resistance to that fuel for that bituminous mixture.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11819-1:2023(Main)
Acoustics - Measurement of the influence of road surfaces on traffic noise - Part 1: Statistical Pass-By method (ISO 11819-1:2023)
SIST EN ISO 11819-1:2023

This document specifies a method of comparing traffic noise on different road surfaces for various compositions of road traffic for the purpose of evaluating different road surface types. Sound levels representing either light or heavy vehicles at selected speeds are assigned to a certain road surface. The method is applicable to traffic travelling at constant speed, i.e. free-flowing conditions at posted speeds of 50 km/h and upwards. For conditions where traffic is not free flowing, such as at junctions and where the traffic is congested, the method is not applicable.
A standard method for comparing the noise characteristics of road surfaces gives road and environment authorities a tool for establishing common practices or limits regarding the use of road surfaces meeting certain noise criteria. However, it is not within the scope of ISO 11819 (all parts) to suggest such criteria.
The statistical pass-by (SPB) method is suitable for use for the following main purposes:
—    to classify road surfaces according to their influence on traffic noise (surface classification);
—    to assist in verifying conformity of production of road surfaces;
—    to evaluate acoustic performance of road surfaces throughout operation relative to new condition;
—    to evaluate the influence of different road surfaces on traffic noise at sites irrespective of condition and service time;
—    to evaluate acoustic performance of a road surface relative to a reference surface.
Due to practical restrictions, the method cannot be applied at all possible locations. However, the backing board method can allow some locations to be tested that were not previously acceptable.
Clause 5 gives a general description of the SPB method.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-41:2023(Main)
Bituminous mixtures - Test methods - Part 41: Resistance to de-icing fluids
SIST EN 12697-41:2023

This document specifies a test method to determine the resistance of bituminous materials to de-icing fluids. The procedure determines the surface tensile strength of a specimen of asphalt which has been stored in de-icing fluid.
This document is primarily used as a test on asphalt to be laid on airfields, but it can be used for asphalt to be laid on roads or other paved areas.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-26:2018+A1:2022(Main + Amendment)
Bituminous mixtures - Test methods - Part 26: Stiffness
SIST EN 12697-26:2018+A1:2022

This European Standard specifies the methods for characterizing the stiffness of bituminous mixtures by alternative tests, including bending tests and direct and indirect tensile tests. The tests are performed on compacted bituminous material under a sinusoidal loading or other controlled loading, using different types of specimens and supports.
The procedure is used to rank bituminous mixtures on the basis of stiffness, as a guide to relative performance in the pavement, to obtain data for estimating the structural behaviour in the road and to judge test data according to specifications for bituminous mixtures.
As this standard does not impose a particular type of testing device the precise choice of the test conditions depends on the operating scope and working range of the device used.
For the choice of specific test conditions, the requirements of the product standards for bituminous mixtures should be respected.
The applicability of this document is described in the product standards for bituminous mixtures.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-33:2019+A1:2022(Main + Amendment)
Bituminous mixtures - Test method - Part 33: Specimen prepared by roller compactor
SIST EN 12697-33:2019+A1:2022

This document specifies the methods for compacting parallelepipedal specimens (slabs) of bituminous mixtures, to be used directly for subsequent testing, or from which test specimens are cut.
For a given mass of bituminous mixture, the specimens are prepared either under controlled compaction energy, or until a specified volume and therefore air voids content is obtained.
This document describes the following methods of compaction:
- method using a wheel or two wheels fitted with pneumatic tyres;
- methods using a steel roller, which includes 3 different procedures:
- steel roller;
- steel roller used on wheel fitted with pneumatic tyres;
- steel roller running on vertical sliding steel plates;
- method using a steel roller sector.
This document is applicable to bituminous mixtures manufactured in the laboratory or in a mixing plant.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-36:2022(Main)
Bituminous mixtures - Test methods - Part 36: Determination of the thickness of bituminous pavement
SIST EN 12697-36:2022

This document describes two test methods for determining the thickness of bituminous pavement. The first method describes measurements carried out on one or more cores which have been drilled from the full depth of the slab or road structure (destructive method). The second method electro-magnetic (non-destructive) measurement are used.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-15:2022(Main)
Bituminous mixtures - Test methods - Part 15: Determination of the segregation sensitivity
SIST EN 12697-15:2022

This document specifies a test method for the determination of the mixing quality and the tendency of segregation in composition of bituminous mixtures. This test method is considered suitable for mix-design purposes and for client information.
NOTE This test method is based on hot bituminous mixtures. There is no experience for other types of bituminous mixtures, e.g. asphalt concrete with bituminous emulsions.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-7:2022(Main)
Bituminous mixtures - Test methods - Part 7: Determination of the bulk density of bituminous specimens by gamma rays
SIST EN 12697-7:2022

This document specifies a method for measuring the bulk density of pavement mixtures using a transmission-type gamma radiation test bench.
This method applies to cylindrical specimens or parallelepipedal blocks, prepared in a laboratory or cut from a pavement. The thickness and the mass absorption coefficient, which is a function of the chemical composition, are known. The thickness of the specimen body traversed by the radiation is between 30 mm and 300 mm.
The method cannot be applied to materials containing slags, with variable metal content or chemical composition.
NOTE   Material containing metal or chemical compositions can affect the absorption of gamma rays.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12697-37:2022(Main)
Bituminous mixtures - Test methods - Part 37: Hot sand test for the adhesivity of binder on pre-coated chippings for Hot-Rolled-Asphalt (HRA)
SIST EN 12697-37:2022

This document describes a hot sand test method for determining the condition of the binder on coated chippings for use with hot rolled asphalt (HRA) surface course.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day