EN 13467:2001

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije – Ugotavljanje mer, pravokotnosti in ravnosti predoblikovanih cevnih izolacijWärmedämmstoffe für die Haustechnik und für betriebstechnische Anlagen - Bestimmung der Maße, der Rechtwinkligkeit und der Linearität von vorgeformten RohrdämmstoffenProduits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Détermination des dimensions, de l'équerrage et de la linéarité des coquilles isolantes préforméesThermal insulating products for building equipment and industrial installations - Determination of dimensions, squareness and linearity of preformed pipe insulation91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 13467:2001SIST EN 13467:2002en01-marec-2002SIST EN 13467:2002SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13467September 2001ICS 91.100.60English versionThermal insulating products for building equipment and industrialinstallations - Determination of dimensions, squareness andlinearity of preformed pipe insulationProduits isolants thermiques pour l'équipement du bâtimentet les installations industrielles - Détermination desdimensions, de l'équerrage et de la linéarité des coquillesisolantes préforméesWärmedämmstoffe für die Haustechnik und fürbetriebstechnische Anlagen - Bestimmung der Maße, derRechtwinkligkeit und der Linearität von vorgeformtenRohrdämmstoffenThis European Standard was approved by CEN on 18 August 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13467:2001 ESIST EN 13467:2002

Measurement and calculation of dimensions.11SIST EN 13467:2002

For circumference, outside and inside diameter and thickness5.1.1
Metal tape graduated in millimetres for measuring circumference and diameter.Accuracy of reading:diameterat least 1 mm,circumferenceat least 3 mm.5.1.2
Metal pipe for supporting the insulation with an outside diameter which ensures no deformation ofthe product5.1.3
Rack for supporting the metal pipe (see Figure 2).5.1.4
Thickness gauge, capable of applying a load of minimum (0,5 ± 0,05) N to a load distributingplate, diameter 50 mm. The load shall be such that no deformation of the product occurs duringmeasurement.Accuracy of reading at least 0,5 mm.5.1.5
Conical mandrel graduated in 0,5 mm intervals (see Figure 3).Accuracy of reading at least 0,5 mm.SIST EN 13467:2002

CaliperAccuracy of reading at least 0,1 mm.5.2
For length5.2.1
Metal tape graduated in millimetres.Accuracy of reading at least 1 mm.5.3
For deviation from squareness5.3.1 Metal square with limbs at least 500 mm long with a deviation from squareness of not more than± 0,1 mm when measured at 500 mm from the corners (see Figure 4).5.3.2
Metal tape graduated in millimetres.Accuracy of reading at least 1 mm.5.4
For deviation from linearity5.4.1
Flat surface on which the test specimen rests.5.4.2
Metal tape graduated in millimetres.Accuracy of reading at least 1 mm.5.4.3
Thickness gauge (wedgeshape), graduated in 0,5 mm (see Figure 5).Accuracy of reading at least 0,5 mm.NOTE
For all measured dimensions test equipment which provides the same result with at lea
...