iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13116:2024

(Main)

Curtain walling - Resistance to wind load - Performance requirements

Curtain walling - Resistance to wind load - Performance requirements

This document specifies the structural performance requirements of curtain walling under wind load, both its fixed and openable parts, under positive and negative static air pressure.
This document applies to any curtain walling product as defined in EN 13830.

Vorhangfassaden - Widerstand gegen Windlast - Leistungsanforderungen

Dieses Dokument legt die Bauleistungsanforderungen an sowohl ortsfeste als auch zu öffnende Teile von Vorhangfassaden unter Windlast bei positivem und negativem statischem Druck fest.
Dieses Dokument ist für alle in EN 13830 festgelegten Produkte von Vorhangfassaden anwendbar.
ANMERKUNG   Aufgrund der Vielzahl an den sich beim Einbau von Vorhangfassaden anzupassenden unterschiedlichen Aufrissdarstellungen und Maßabweichungen, ist es nicht sinnvoll, die vielfältigen Vorhangfassaden¬systeme und nach Kundenangaben gefertigten Ausführungen konstruktiv zu klassifizieren.

Façades rideaux - Résistance au vent - Exigences de performances

Ce document définit les prescriptions de performance structurelle des façades rideaux sous la charge du vent, pour les parties fixes et ouvrantes, sous une pression statique positive et négative.
Ce document s'applique à tous les produits de façades rideaux suivant la définition donnée dans l'EN 13830.
NOTE En raison des nombreuses configurations d'élévation et des variations diverses qui sont prises en compte par les installations de façades-rideaux, il n'est pas pratique de classer la grande variété des systèmes de façades-rideaux et de constructions spécialement conçues.

Obešene fasade - Odpornost proti obremenitvi z vetrom - Zahtevane lastnosti

Ta dokument določa zahteve glede učinkovitosti konstrukcije obešenih fasad pri vetrni obremenitvi tako fiksnih kot premičnih delov obešenih fasad pod pozitivnim in negativnim statističnim zračnim tlakom.
Ta dokument se uporablja za vse proizvode obešene fasade, kot je določeno v standardu EN 13830.

General Information

Status
Published
Publication Date
13-Feb-2024
ICS
91.060.10 - Walls. Partitions. Facades
Technical Committee
CEN/TC 33 - Doors, windows, shutters and building hardware
Drafting Committee
CEN/TC 33/WG 6 - Curtain walling
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
14-Feb-2024
Due Date
02-May-2024
Completion Date
14-Feb-2024
Ref Project
SIST EN 13116:2024 - Curtain walling - Resistance to wind load - Performance requirements

Relations

Replaces
EN 13116:2001 - Curtain walling - Resistance to wind load - Performance requirements
Effective Date
26-Jan-2022

Buy Standard

EN 13116:2024EN 13116:2024
PreviousNext
Standard
EN 13116:2024
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2024
Nadomešča:
SIST EN 13116:2002
Obešene fasade - Odpornost proti obremenitvi z vetrom - Zahtevane lastnosti
Curtain walling - Resistance to wind load - Performance requirements
Vorhangfassaden - Widerstand gegen Windlast - Leistungsanforderungen
Façade rideaux - Résistance structurelle au vent - Prescriptions de performance
Ta slovenski standard je istoveten z: EN 13116:2024
ICS:
91.060.10 Stene. Predelne stene. Walls. Partitions. Facades
Fasade
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13116
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2024
EUROPÄISCHE NORM
ICS 91.060.10 Supersedes EN 13116:2001
English Version
Curtain walling - Resistance to wind load - Performance
requirements
Façades rideaux - Résistance au vent - Exigences de Vorhangfassaden - Widerstand gegen Windlast -
performances Leistungsanforderungen
This European Standard was approved by CEN on 24 December 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13116:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements . 5
4.1 General . 5
4.2 Performance under design wind load (serviceability limit state) . 5
4.3 Performance under increased wind load (ultimate limit state) . 5
5 Test methods . 6
Bibliography . 7

European foreword
This document (EN 13116:2024) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2024, and conflicting national standards shall be
withdrawn at the latest by August 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13116:2001.
This document forms part of a series of European Standards dedicated to curtain walling products as
defined in the curtain walling product standard EN 13830.
This document complements a series of curtain walling standards for performance requirements and
methods of test as defined in the product standard EN 13830.
In comparison with the previous edition EN 13116:2001, the following modifications have been made:
— normative references updated;
— alignment of the deflection limits in accordance with EN 13830.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
follo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12152:2023(Main)
Curtain walling - Air permeability - Performance requirements and classification
SIST EN 12152:2023

This document specifies requirements and classification of air permeability of both fixed and openable parts of curtain walling, under positive and negative static air pressure.
This document applies to curtain walling as specified in EN 13830.
NOTE   This version of EN 12152:2023 will supersede EN 12152:2002. Existing test results according to EN 12152:2002 could be considered still valid compared with this version of EN 12152.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12153:2023(Main)
Curtain walling - Air permeability - Test method
SIST EN 12153:2023

This document defines the method to be used to determine the air permeability of curtain walling, both its fixed and openable parts. It describes how the specimen shall be tested under positive and negative air pressure.
This document applies to any curtain walling product as defined in EN 13830.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14024:2023(Main)
Metal profiles with thermal barrier - Mechanical performance - Requirements, proof and tests for assessment
SIST EN 14024:2023

This document specifies requirements for assessment of the mechanical strength of metal profiles incorporating a thermal barrier having mechanical performance depending on their intended use.
It also specifies the tests to determine the characteristic values of mechanical properties of the thermal barrier profile and to assess the effect of different conditionings of the thermal barrier on the mechanical performance of the connection.
This document does not apply to thermal barriers which do not give a contribution to the mechanical resistance of the profiles.
This document is applicable to thermal barrier profiles designed mainly for windows, doors, screens and curtain walls.
This document does not apply to thermal barriers made only of metal profiles connected with metal pins or screws.
This current edition of EN 14024 will supersede EN 14024:2004. Differences in test procedures between the two versions will not lead to significant differences in test results. Therefore, existing test results according to EN 14024:2004 are considered as equivalent to new test results according to the current edition of EN 14024.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13830:2015+A1:2020/AC:2022(Corrigendum)
Curtain walling - Product standard
SIST EN 13830:2015+A1:2020/AC:2022

This European Standard specifies requirements of curtain walling kit intended to be used as a building envelope to provide weather resistance, safety in use and energy economy and heat retention and provides test/assessments/calculation methods and compliance criteria of the related performances.
The curtain walling kit covered by this standard should fulfil its own integrity and mechanical stability but does not contribute to the load bearing or stability of the main building structure, and could be replaced independently of it.
This standard applies to curtain walling kit ranging from a vertical position to ± 15° from the vertical. Any sloping parts should be contained within the curtain walling kit.
This standard is applicable to the whole of the curtain walling kits, including the fixings.
Curtain walling according to this standard is intended to be used as part of the building envelope.
This European Standard does not include:
—   “Patent glazing” (glazed sloping roofs) kits;
—   Roof glazing constructions;
—   Façades made of precast concrete panels as part of the wall (see EN 14992).
NOTE 1   Precast concrete panels may be used in curtain walling kits as infill panels.
NOTE 2   Durability of structural sealed glazing infills is not covered by this standard.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16758:2021(Main)
Curtain walling - Determination of the strength of shear connections - Test method and requirements
SIST EN 16758:2021

This document specifies test methods for the determination of bearing capacity (ultimate limit state and serviceability limit state), of connections between curtain walling framing members which cannot be calculated in accordance with current codes or conventional calculations based upon the strength of the materials.
Mechanical performances of the curtain walling connections are already assessed in accordance with the provisions described in EN 13830. Additional information with respect to mechanical performance of the connections and direct applications can be determined with this document (see Annex C).

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13830:2015+A1:2020(Main)
Curtain walling - Product standard
SIST EN 13830:2015+A1:2020

This European Standard specifies requirements of curtain walling kit intended to be used as a building envelope to provide weather resistance, safety in use and energy economy and heat retention and provides test/assessments/calculation methods and compliance criteria of the related performances.
The curtain walling kit covered by this standard should fulfil its own integrity and mechanical stability but does not contribute to the load bearing or stability of the main building structure, and could be replaced independently of it.
This standard applies to curtain walling kit ranging from a vertical position to ± 15° from the vertical. Any sloping parts should be contained within the curtain walling kit.
This standard is applicable to the whole of the curtain walling kits, including the fixings.
Curtain walling according to this standard is intended to be used as part of the building envelope.
This European Standard does not include:
—   “Patent glazing” (glazed sloping roofs) kits;
—   Roof glazing constructions;
—   Façades made of precast concrete panels as part of the wall (see EN 14992).
NOTE 1   Precast concrete panels may be used in curtain walling kits as infill panels.
NOTE 2   Durability of structural sealed glazing infills is not covered by this standard.

  • Standard
    90 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17146:2018(Main)
Determination of the strength of infill supports - Test method and requirements
SIST EN 17146:2019

This document specifies test methods for the determination of the bearing capacity (ultimate limit state and serviceability limit state) of infill support which cannot be calculated in accordance with current codes or conventional calculations based upon the strength of the materials or to compare the calculation when necessary.
Three different types of infill (glass) supports are dealt in this standard:
- The cantilever infill (glass) supports, see Figure 1 (a);
- The cruciform infill (glass) supports only fixed to the mullion, see Figure 1 (b);
- Corner infill (glass) supports only fixed to the mullion, see Figure 1 (c).
The test method is intended for the assessment of cantilever infill (glass) supports that have not been tested according to EN 16758 (see Figure 9). The results of the test method can only be interpreted when incorporated with the results from a test in accordance with EN 16758.
It is essential that cruciform and corner infill (glass) supports only fixed to the mullion are tested in accordance with this standard.
The infill (glass) supports connected to the mullion and the transom together are considered as a part of sheared connection and are covered by EN 16758.
Where the mechanical performances of the infill (glass) support is already assessed in accordance with the provisions described in EN 13830, additional information with respect to mechanical performance of the infill (glass) support and direct applications can be determined with this standard.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13119:2016(Main)
Curtain walling - Terminology
SIST EN 13119:2016

This European Standard de¬scribes terminology used in documents, drawings, specifications etc., when referring to the detailed elements of curtain wall¬ing and provides a comprehensive, though not total, list of regu¬lar terms.
It does not set out to repeat those physical definitions properly included within individual curtain walling standards related to performance requirements and associated test methods.

  • Standard
    25 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14019:2016(Main)
Curtain Walling - Impact resistance - Performance requirements
SIST EN 14019:2016

This European Standard defines performance requirements of curtain walling (excluding ‘glass in building’ which is classified under EN 12600) under soft body impact load criteria specified herein and tested in accordance with EN 13049.
Its criteria is targeted to safety in use and integrity of curtain wall in the event of sudden impact forces on the curtain wall surfaces. Compliance with the performance requirement is determined by the laboratory test.
It applies to those areas of curtain walling which face onto areas of human activity, either internally or externally and takes account of accidental impacts brought on by people going about their normal daily activities and impacts brought about by equipment and similar devices for maintenance, cleaning, repair and similar occasional activities.
It does not set out to define performance requirements of impact under exceptional circumstances such as acts of vandalism, vehicular collision, firearm projectiles, etc..
This standard will have no bearing whatsoever on any National Building / Health and Safety regulations which may exist and whose requirements shall apply separately and in parallel with these test performance requirements.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13050:2011(Main)
Curtain Walling - Watertightness - Laboratory test under dynamic condition of air pressure and water spray
SIST EN 13050:2011

This European Standard defines an additional test method which may be used when assessing the watertightness of curtain walling, both its fixed and openable parts. It is a supplementary test, not required for classification purposes, and it should be used only when the project specifier has determined its necessity.
This European Standard describes how the outside face of a curtain walling specimen should be subjected to a continuous spray of water and a turbulent airflow, with continuous pulses of positive air pressure on the outside of the test specimen generated from within the chamber.
This European Standard applies to any curtain walling product as defined in EN 13830.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day