iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN ISO 15118-21

(Main)

Road vehicles - Vehicle to grid communication interface - Part 21: Common 2nd generation network layer and application layer requirements conformance test plan (ISO/DIS 15118-21:2024)

Road vehicles - Vehicle to grid communication interface - Part 21: Common 2nd generation network layer and application layer requirements conformance test plan (ISO/DIS 15118-21:2024)

The document specifies all common test cases to be applied to and correctly handled by EVs (EVCC) and EVSEs (SECC) implementing ISO 15118-20 that are independent of a particular charging type (AC, DC, ACD, WPT charging). The document considers the use cases defined in ISO 15118-1:2019
The test system will comprise:
-   A simulated SECC to verify the correct behaviour of a real EVCC
-   A simulated EVCC to verify the correct behaviour of a real SECC
The document specifies test cases for all requirements defined in ISO 15118-20, verifying at least the following aspects:
-   Charge spot discovery and initialization of communication (TCP / TLS connection establishment).
-   Session establishment, session interruption and session re-establishment.
-   Authentication process for charging session (e.g. EIM and PNC)
-   Service discovery and selection
-   Common and charging type independent service implementation
-   Termination of charging session
-   Error handling
The test cases cover positive tests (according to ISO 15118-20). In addition, error scenarios (e.g., incorrectly formatted requests, invalid content of messages, etc.) as well as tests for timing behaviour are defined which are also handled by EVCC and SECC ensuring interoperability between EVs and EVSEs.
The test cases will be structured according to OSI-layers 3 to 7 depending on their testability from a (non-) functional perspective (e.g., IPv6, TCP, TLS.
The test cases will include standard test case attributes like pre-conditions, test behaviours, expected results to evaluate pass or fail and post-conditions to be applied returning the system under test to a safe state.

Véhicules routiers - Interface de communication entre véhicule et réseau électrique - Partie 21: Plan de test de conformité aux exigences communes de la couche réseau et de la couche application de 2ème génération (ISO/DIS 15118-21:2024)

Cestna vozila - Komunikacijski vmesnik med vozilom in omrežjem - 21. del: Načrt preskusa skladnosti z zahtevami za skupno omrežno in aplikacijsko plast druge generacije (ISO/DIS 15118-21:2024)

General Information

Status
Not Published
Publication Date
20-Oct-2025
ICS
43.120 - Electric road vehicles
Technical Committee
CEN/TC 301 - Electrically propelled road vehicles
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
28-Mar-2024
Completion Date
28-Mar-2024
Ref Project
oSIST prEN ISO 15118-21:2024 - Road vehicles - Vehicle to grid communication interface - Part 21: Common 2nd generation network layer and application layer requirements conformance test plan (ISO/DIS 15118-21:2024)

Buy Standard

prEN ISO 15118-21:2024 - BARVEprEN ISO 15118-21:2024 - BARVE
PreviousNext
Draft
prEN ISO 15118-21:2024 - BARVE
English language
235 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 15118-21:2024
01-junij-2024
Cestna vozila - Komunikacijski vmesnik med vozilom in omrežjem - 21. del: Načrt
preskusa skladnosti z zahtevami za skupno omrežno in aplikacijsko plast druge
generacije (ISO/DIS 15118-21:2024)
Road vehicles - Vehicle to grid communication interface - Part 21: Common 2nd
generation network layer and application layer requirements conformance test plan
(ISO/DIS 15118-21:2024)
Véhicules routiers - Interface de communication entre véhicule et réseau électrique -
Partie 21: Plan de test de conformité aux exigences communes de la couche réseau et
de la couche application de 2ème génération (ISO/DIS 15118-21:2024)
Ta slovenski standard je istoveten z: prEN ISO 15118-21
ICS:
35.100.05 Večslojne uporabniške Multilayer applications
rešitve
43.040.15 Avtomobilska informatika. Car informatics. On board
Vgrajeni računalniški sistemi computer systems
oSIST prEN ISO 15118-21:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 15118-21:2024

---------------------- Page: 2 ----------------------
oSIST prEN ISO 15118-21:2024
DRAFT
International
Standard
ISO/DIS 15118-21
ISO/TC 22/SC 31
Road vehicles — Vehicle to grid
Secretariat: DIN
communication interface —
Voting begins on:
Part 21: 2024-03-25
Common 2nd generation network
Voting terminates on:
2024-06-17
layer and application layer
requirements conformance test plan
Véhicules routiers — Interface de communication entre véhicule
et réseau électrique —
Partie 21: Plan de test de conformité aux exigences communes de
la couche réseau et de la couche application de 2ème génération
ICS: 43.120
IMPORTANT — Please use this updated version dated 2024-03-21,
THIS DOCUMENT IS A DRAFT CIRCULATED
and discard any previous version of this DIS
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 15118-21:2024(en)
© ISO 2024

---------------------- Page: 3 ----------------------
oSIST prEN ISO 15118-21:2024
ISO/DIS 15118-21:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland

© ISO 2024 – All rights reserved
ii

---------------------- Page: 4 ----------------------
oSIST prEN ISO 15118-21:2024
ISO/DIS 15118-21:2024(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Abbreviated terms .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 15118-9:2023(Main)
Road vehicles - Vehicle to grid communication interface - Part 9: Physical and data link layer conformance test for wireless communication (ISO 15118-9:2022)
SIST EN ISO 15118-9:2023

This document specifies conformance tests in the form of an abstract test suite (ATS) for a system under test (SUT) implementing an electric-vehicle or supply-equipment communication controller (EVCC or SECC) with support for WLAN-based high-level communication (HLC) according to ISO 15118‑8 and against the background of ISO 15118-1. These conformance tests specify the testing of capabilities and behaviours of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118‑8 and against what the implementer states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118‑8. The behaviour tests of the ATS examine an implementation as thoroughly as practical over the full range of dynamic conformance requirements defined in ISO 15118‑8 and within the capabilities of the SUT (see NOTE below).
A test architecture is described in correspondence to the ATS. The abstract test cases in this document are described leveraging this test architecture and are specified in descriptive tabular format for the ISO/OSI physical and data link layers (layers 1 and 2).
In terms of coverage, this document only covers normative sections and requirements in ISO 15118‑8. This document can additionally refer to specific tests for requirements on referenced standards (e.g. IEEE, or industry consortia standards, like WiFi Alliance) as long as they are relevant in terms of conformance for implementations according to ISO 15118‑8. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118‑8. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the abstract test cases defined in this document only consider the communication protocol and the system's behaviour defined ISO 15118‑8. The power flow between the EVSE and the EV is not considered.
NOTE       Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus, conformance to a test suite alone cannot guarantee interworking. Instead, it gives confidence that an implementation has the required capabilities and that its behaviour conforms consistently in representative instances of communication.

  • Standard
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-20:2022(Main)
Road vehicles - Vehicle to grid communication interface - Part 20: 2nd generation network layer and application layer requirements (ISO 15118-20:2022)
SIST EN ISO 15118-20:2022

This document specifies the communication between the electric vehicle (EV), including battery electric vehicle (BEV) and plug-in hybrid electric vehicle (PHEV), and the electric vehicle supply equipment (EVSE). The application layer messages defined in this document are designed to support the electricity power transfer between an EV and an EVSE.
This document defines the communication messages and sequence requirements for bidirectional power transfer.
This document furthermore defines requirements of wireless communication for both conductive charging and wireless charging as well as communication requirements for automatic connection device and information services about charging and control status.
The purpose of this document is to detail the communication between an electric vehicle communication controller (EVCC) and a supply equipment communication controller (SECC). Aspects are specified to detect a vehicle in a communication network and enable an Internet Protocol (IP) based communication between the EVCC and the SECC.

  • Standard
    570 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    571 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19363:2021(Main)
Electrically propelled road vehicles - Magnetic field wireless power transfer - Safety and interoperability requirements (ISO 19363:2020)
SIST EN ISO 19363:2021

This document defines the requirements and operation of the on-board vehicle equipment that enables magnetic field wireless power transfer (MF-WPT) for traction battery charging of electric vehicles. It is intended to be used for passenger cars and light duty vehicles.
This document addresses the following aspects for an EV device:
—     safety requirements;
—     transferred power and power transfer efficiency;
—     ground clearance of the EV device;
—     functionality with associated off-board systems under various conditions and independent of manufacturer;
—     test procedures.
EV devices that fulfil the requirements in this document are intended to operate with supply devices that fulfil the MF-WPT related requirements in the IEC 61980 series.
NOTE 1  Charging of a vehicle in motion is not considered in this edition.
NOTE 2  Bi-directional power transfer is not considered in this edition.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-8:2020(Main)
Road vehicles - Vehicle to grid communication interface - Part 8: Physical layer and data link layer requirements for wireless communication (ISO 15118-8:2020)
SIST EN ISO 15118-8:2020

This document specifies the requirements of the physical and data link layer of a wireless High Level Communication (HLC) between Electric Vehicles (EV) and the Electric Vehicle Supply Equipment (EVSE). The wireless communication technology is used as an alternative to the wired communication technology as defined in ISO 15118‑3.
It covers the overall information exchange between all actors involved in the electrical energy exchange. ISO 15118 (all parts) are applicable for conductive charging as well as Wireless Power Transfer (WPT).
For conductive charging, only EVSEs compliant with "IEC 61851‑1 modes 3 and 4" and supporting HLC are covered by this document. For WPT, charging sites according to IEC 61980 (all parts) and vehicles according to ISO 19363 are covered by this document.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17409:2020(Main)
Electrically propelled road vehicles - Conductive power transfer - Safety requirements (ISO 17409:2020)
SIST EN ISO 17409:2020

This document specifies electric safety requirements for conductive connection of electrically propelled road vehicles to external electric circuits. External electric circuits include external electric power supplies and external electric loads. This document provides requirements for the charging modes 2, 3, 4, as defined in IEC 61851-1, and reverse power transfer. For mode 4, this document provides requirements regarding the connection to an isolated DC EV charging station according to IEC 61851-23.
NOTE 1  This edition does not provide requirements for mode 1.
NOTE 2  External electric circuits are not part of the vehicle.
This document applies to the on-board sections of vehicle power supply circuits. It applies also to dedicated power supply control functions used for the connection of the vehicle to an external electric circuit.
It does not provide comprehensive safety information for manufacturing, maintenance and repair personnel.
NOTE 3  ISO 6469-3 provides general electrical safety requirements for electrically propelled road vehicles.
NOTE 4  With this edition of this document the limitation of y-capacitance for protection against electric shock under single failure conditions is no longer applicable as a fault protection provision when the vehicle has a conductive DC connection to an external electric circuit.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-1:2019(Main)
Road vehicles - Vehicle to grid communication interface - Part 1: General information and use-case definition (ISO 15118-1:2019)
SIST EN ISO 15118-1:2019

This document, as a basis for the other parts of the ISO 15118 series, specifies terms and definitions, general requirements and use cases for conductive and wireless HLC between the EVCC and the SECC.
This document is applicable to HLC involved in conductive and wireless power transfer technologies in the context of manual or automatic connection devices.
This document is also applicable to energy transfer either from EV supply equipment to charge the EV battery or from EV battery to EV supply equipment in order to supply energy to home, to loads or to the grid.
This document provides a general overview and a common understanding of aspects influencing identification, association, charge or discharge control and optimisation, payment, load levelling, cybersecurity and privacy. It offers an interoperable EV-EV supply equipment interface to all e-mobility actors beyond SECC.
The ISO 15118 series does not specify the vehicle internal communication between battery and other internal equipment (beside some dedicated message elements related to the energy transfer).
NOTE 1    Electric road vehicles specifically are vehicles in categories M (used for carriage of passengers) and N (used for carriage of goods) (compare ECE/TR ANS/WP.29/78 ev.2). This does not prevent vehicles in other categories from adopting the ISO 15118 series as well.
NOTE 2    This document is destined to orientate the message set of ISO 15118‑2 and ISO 15118‑20[1]. The absence of any particular use case in this document does not imply that it will not be put into practice, with the required messages.
NOTE 3    This document, ISO 15118‑2 and ISO 15118‑20 are designed to work independent of data transfer medium used. However, the ISO 15118 series is made for fitting the specified data link layers in the corresponding documents in this series.
[1] Under preparation. Stage at the time on publication: ISO/DIS 15118-20:2019.

  • Standard
    126 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    130 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17186:2019(Main)
Identification of vehicles and infrastructures compatibility - Graphical expression for consumer information on EV power supply
SIST EN 17186:2019

This document lays down harmonized identifiers for power supply for electric road vehicles. The requirements in this standard are to complement the informational needs of users regarding the compatibility between the EV charging stations, the cable assemblies and the vehicles that are placed on the market. The identifier is intended to be visualized at EV charging stations, on vehicles, on cable assemblies, in EV dealerships and in consumer manuals as described in this document.
Power supply for EVs uses vehicle inlets, socket-outlets, connectors and plugs, as mentioned in EN IEC 61851-1:— and EN 62196-1:2014.
This document defines for each harmonized identifier the size, shape, colour and other information of relevance for compatibility recognition, as well as the label location.
The station side identifier gives unmistakable compatibility information with either the plug of the cable assembly in case of a socket outlet configuration, or the vehicle inlet in case of attached cable configuration.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-5:2019(Main)
Road vehicles - Vehicle to grid communication interface - Part 5: Physical layer and data link layer conformance test (ISO 15118-5:2018)
SIST EN ISO 15118-5:2019

ISO 15118-5:2018 specifies conformance tests in the form of an Abstract Test Suite (ATS) for a System Under Test (SUT) implementing an Electric Vehicle or Supply Equipment Communication Controller (EVCC or SECC) with support for PLC-based High Level Communication (HLC) and Basic Signaling according to ISO 15118‑3. These conformance tests specify the testing of capabilities and behaviors of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118‑3 and against what the implementer states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118‑3. The behavior tests of the ATS examine an implementation as thoroughly as is practical over the full range of dynamic conformance requirements defined in ISO 15118‑3 and within the capabilities of the SUT (see NOTE 1).
A test architecture is described in correspondence to the ATS. The conformance test cases in this part of the standard are described leveraging this test architecture and are specified in TTCN-3 Core Language for the ISO/OSI Physical and Data Link Layers (Layers 1 and 2). The conformance test cases for the ISO/OSI Network Layer (Layer 3) and above are described in ISO 15118‑4.
In terms of coverage, this document only covers normative sections and requirements in ISO 15118‑3. This document can additionally include specific tests for requirements of referenced standards (e.g. IEEE, or industry consortia standards) as long as they are relevant in terms of conformance for implementations according to ISO 15118‑3. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118‑3. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the test cases defined in this document only consider the communication protocol and the system's behavior defined ISO 15118‑3. Power flow between the EVSE and the EV is not considered.
NOTE 1    Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus conformance to a test suite alone cannot guarantee interworking. What it does do is give confidence that an implementation has the required capabilities and that its behavior conforms consistently in representative instances of communication.
NOTE 2    This document has some interdependencies to the conformance tests defined in ISO 15118‑4 which result from ISO/OSI cross layer dependencies in the underlying protocol specification (e.g. for

  • Standard
    414 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    411 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-4:2019(Main)
Road vehicles - Vehicle to grid communication interface - Part 4: Network and application protocol conformance test (ISO 15118-4:2018)
SIST EN ISO 15118-4:2019

ISO 15118-4:2018 specifies conformance tests in the form of an Abstract Test Suite (ATS) for a System Under Test (SUT) implementing an EVCC or SECC according to ISO 15118-2. These conformance tests specify the testing of capabilities and behaviors of an SUT as well as checking what is observed against the conformance requirements specified in ISO 15118-2 and against what the supplier states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118-2. The behavior tests of the ATS examine an implementation as thoroughly as is practical over the full range of dynamic conformance requirements defined in ISO 15118-2 and within the capabilities of the SUT (see NOTE).
A test architecture is described in correspondence to the ATS. The conformance test cases in this document are described leveraging this test architecture and are specified in TTCN-3 Core Language for ISO/OSI Network Layer (Layer 3) and above. The conformance test cases for the Data Link Layer (Layer 2) and Physical Layer (Layer 1) are described in ISO 15118-5. Test cases with overlapping scopes are explicitly detailed.
This document does not include specific tests of other standards referenced within ISO 15118-2, e.g. IETF RFCs. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the test cases defined in this document only consider the communication protocol defined ISO 15118-2. Power flow between the EVSE and the EV is not considered.
NOTE 1    Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus conformance to a test suite alone cannot guarantee interworking. What it does do is give confidence that an implementation has the required capabilities and that its behavior conforms consistently in representative instances of communication.
NOTE 2    This document has some interdependencies to the conformance tests defined in ISO 15118-5 which result from ISO/OSI cross layer dependencies in the underlying protocol specification (e.g. for sleep mode)

  • Standard
    1470 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    1467 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15118-3:2016(Main)
Road vehicles - Vehicle to grid Communication interface - Part 3: Physical and data link layer requirements (ISO 15118-3:2015)
SIST EN ISO 15118-3:2016

ISO 15118-3:2015 specifies the requirements of the physical and data link layer for a high-level communication, directly between battery electric vehicles (BEV) or plug-in hybrid electric vehicles (PHEV), termed as EV (electric vehicle) [ISO-1], based on a wired communication technology and the fixed electrical charging installation [Electric Vehicle Supply Equipment (EVSE)] used in addition to the basic signalling, as defined in [IEC-1].
It covers the overall information exchange between all actors involved in the electrical energy exchange. ISO 15118 (all parts) is applicable for manually connected conductive charging.
Only "[IEC-1] modes 3 and 4" EVSEs, with a high-level communication module, are covered by this part of ISO 15118.

  • Standard
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day