EN 14399-6:2005
(Main)High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
This part of this European Standard specifies, together with prEN 14399-1, hardened and tempered plain washers with chamfer intended for assembly with large series hexagon high-strength structural bolts and nuts with thread sizes from M12 to M36 inclusive.
NOTE Attention is drawn to the importance of ensuring that the washers are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to ENV 1090-1 is made.
Hochfeste planmäßig vorspannbare Schraubenverbindungen für den Metallbau - Teil 6: Flache Scheiben mit Fase
Dieser Teil der europäischen Norm beschreibt, zusammen mit prEN 14399-1, vergütete flache Scheiben mit Fase, welche für die Verwendung mit hochfesten vorspannbaren Sechskantschrauben und -muttern mit großer Schlüsselweite für den Metallbau mit Gewindegrößen von M12 bis M36, vorgesehen sind.
ANMERKUNG Damit zufriedenstellende Ergebnisse erreicht werden können, ist auf die korrekte Anwendung der Scheiben besondere Aufmerksamkeit zu richten. Für Empfehlungen zur korrekten Anwendung wird auf ENV 1090-1 hingewiesen.
Boulonnerie de construction métallique à haute résistance apte à la précontrainte - Partie 6 : Rondelles plates chanfreinées
La présente partie de cette Norme européenne, avec le prEN 14399-1, spécifie les exigences applicables aux rondelles plates chanfreinées, trempées et revenues, destinées à être assemblées avec des vis et écrous hexagonaux de construction à haute résistance des systèmes HR ou HV, à surplat de série large et de diamètre de filetage de M12 à M36 inclus.
NOTE Il est important de s'assurer que les rondelles soient utilisées de façon correcte afin d'obtenir un résultat satisfaisant. Pour les recommandations relatives à la bonne utilisation, se référer à l'ENV 1090-1.
Visokotrdnostne strukturne vijačne zveze za prednapetje - 6. del: Ploščate posnete podložke
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2005
9LVRNRWUGQRVWQHVWUXNWXUQHYLMDþQH]YH]H]DSUHGQDSHWMHGHO 3ORãþDWHSRVQHWH
SRGORåNH
High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered
washers
Hochfeste planmäßig vorspannbare Schraubenverbindungen für den Metallbau - Teil 6:
Flache Scheiben mit Fase
Boulonnerie de construction métallique a haute résistance apte a la précontrainte - Partie
6 : Rondelles plates chanfreinées
Ta slovenski standard je istoveten z: EN 14399-6:2005
ICS:
21.060.30 Podložke, varovalni elementi Washers, locking elements
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 14399-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2005
ICS 21.060.30
English version
High-strength structural bolting assemblies for preloading - Part
6: Plain chamfered washers
Boulonnerie de construction métallique à haute résistance Hochfeste planmäßig vorspannbare
apte à la précontrainte - Partie 6 : Rondelles plates Schraubenverbindungen für den Metallbau - Teil 6: Flache
chanfreinées Scheiben mit Fase
This European Standard was approved by CEN on 30 April 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14399-6:2005: E
worldwide for CEN national Members.
Contents page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Dimensions.6
4 Specification and reference standards .7
5 Designation .7
6 Marking .7
Bibliography .8
Foreword
This document (EN 14399-6:2005) has been prepared by Technical Committee CEN /TC 185 "Threaded and
non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by September 2005, and conflicting national standards shall be withdrawn at the
latest by September 2005.
This document includes a Bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Introduction
This document on structural bolting reflects the situation in Europe where two technical solutions exist to achieve the
necessary ductility of bolt/nut/washer assemblies. These solutions utilize different systems (HR and HV) of
bolt/nut/washer assemblies, see Table 1. Both systems are well proved and it is up to the experts responsible for
structural bolting whether they use the one or the other system.
It is, however, important for the performance of the assembly to avoid mixing up the components of both systems.
Therefore, bolts and nuts for both systems are standardized in one single part of this European Standard each and
the marking of the components of the same system is uniform.
Table 1 — Systems of bolt/nut/washer assemblies
Bolt/nut/washer Bolt/nut/washer
assembly assembly
System HR System HV
General
EN
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.