EN 14944-1:2023

SLOVENSKI STANDARD
01-december-2023
Vpliv cementnih proizvodov na pitno vodo – Preskusne metode – 1. del: Vpliv
industrijsko izdelanih cementnih proizvodov na organoleptične parametre
Influence of cementitious products on water intended for human consumption - Test
methods - Part 1: Influence of factory made cementitious products on organoleptic
parameters
Einfluss von zementgebundenen Produkten auf Wasser für den menschlichen Gebrauch
- Prüfverfahren - Teil 1: Einfluss fabrikmäßig hergestellter zementgebundener Produkte
auf organoleptische Parameter
Influence des produits à base de ciment sur l'eau destinée à la consommation humaine -
Méthode d'essai - Partie 1: Influence des produits à base de ciment fabriqués en usine
sur les paramètres organoleptiques
Ta slovenski standard je istoveten z: EN 14944-1:2023
ICS:
13.060.20 Pitna voda Drinking water
67.250 Materiali in predmeti v stiku z Materials and articles in
živili contact with foodstuffs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 14944-1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2023
EUROPÄISCHE NORM
ICS 13.060.20; 67.250 Supersedes EN 14944-1:2006
English Version
Influence of cementitious products on water intended for
human consumption - Test methods - Part 1: Influence of
factory made cementitious products on organoleptic
parameters
Influence des produits à base de ciment sur l'eau Einfluss von zementgebundenen Produkten auf Wasser
destinée à la consommation humaine - Méthode d'essai für den menschlichen Gebrauch - Prüfverfahren - Teil
- Partie 1: Influence des produits à base de ciment 1: Einfluss fabrikmäßig hergestellter
fabriqués en usine sur les paramètres organoleptiques zementgebundener Produkte auf organoleptische
Parameter
This European Standard was approved by CEN on 2 July 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14944-1:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Principle . 9
5 Reagents . 10
6 Apparatus . 11
6.1 General. 11
6.2 Apparatus and materials for test piece preparation (see Annexes A, B and C) . 12
6.3 Apparatus and materials for preconditioning and migration procedure . 13
6.4 Apparatus for odour and flavour assessment . 13
6.5 Apparatus for colour and turbidity assessment . 13
7 Samples and test pieces . 13
7.1 Sampling, transport and storage of samples. 13
7.2 Preparation of test pieces . 14
7.3 Surface area to volume ratio (S/V) for use in the test procedure . 14
8 Pre-treatment of samples (curing and preconditioning) . 15
8.1 General. 15
8.2 Curing . 16
8.3 Preconditioning . 16
9 Test procedure . 16
9.1 General. 16
9.2 Preparation of migration water for the assessment of odour, flavour, colour and
turbidity . 16
9.3 Control samples (blank test) . 17
10 Determination of odour as TON and flavour as TFN . 17
11 Determination of colour and turbidity . 18
12 Determination of TOC and calculation of test results . 18
12.1 Determination of TOC. 18
12.2 Calculation of test results. 18
13 Expression of results . 19
14 Test report . 20
14.1 General. 20
14.2 General information . 20
14.3 Information on the product . 20
14.4 Information on the test procedure . 20
14.5 Test results . 21
Annex A (normative) Additional procedures for testing factory-made pipes (cement mortar
lined and concrete) . 22
Annex B (normative) Additional procedures for testing factory-made fittings (cement
mortar lined and concrete) . 27
Annex C (normative) Additional procedures for testing factory-made storage systems
(cement mortar, cement mortar lined and concrete) . 33
Annex D (informative) Examples of typical test pieces and test conditions as a function
of S/V ratio . 38
Annex E (informative) Test arrangements for testing factory-made cement based products . 43
Annex F (normative) Additional procedures for testing factory-made cement based
products at elevated temperature. 50
Annex G (informative) Discrimination between porous and non-porous coatings on
factory-made products . 52
Annex H (informative) Schematic description of the test procedure . 55
Bibliography . 58

European foreword
This document (EN 14944-1:2023) has been prepared by Technical Committee CEN/TC 164 “Water
supply”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2024, and conflicting national standards shall be
withdrawn at the latest by April 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14944-1:2006.
In comparison with EN 14944-1:2006, the following changes have been made:
— provisions for testing the influence of materials on the migration of organic substances (TOC) have
been added;
— the test method for TON /TFN according to EN 1622 has been specified according to the
revised EN 1420;
— requirements for disinfection (preconditioning with 50 mg/L chlorine) have been removed;
— a procedure for extending the number of migration periods has been included.
This document describes a test method to determine the influence(s) of factory-made cement based
products on organoleptic parameters and the migration of organic substances (TOC) in water intended
for human consumption.
This document will result in one of a series of standards that support standards for the approval of
products and materials in contact with water intended for human consumption.
This document is part of a series dealing with the influence of cement based and associated non-cement
based products/materials on water intended for human consumption, including:
— Part 1: Influence of factory-made cement based products on organoleptic parameters and migration
of organic substances (TOC)
— Part 2: Influence of site-applied cement based materials and associated non-cement based
products/materials on organoleptic parameters and migration of organic substances (TOC)
— Part 3: Migration of substances from factory-made cement based products
— Part 4: Migration of substances from site-applied cement based materials and associated non-cement
based products/materials
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
1 Scope
This document specifies a method to determine the influence of factory-made cement based products
on the odour, flavour, colour, turbidity and total organic carbon (TOC) of test waters after contact with
the products.
This document is applicable to factory-made cement based products, e.g. cement mortar linings to
metallic pipes, tanks, concrete pipes, etc. intended to be used for the transport and storage of water for
human consumption, including raw water used for the production of drinking water.
NOTE Tests with the specified test water will not necessarily be representative of materials used in different
kinds of waters and especially ve
...