Respiratory protective devices - Powered filtering devices incorporating full face masks, half masks or quarter masks - Requirements, testing, marking

This document specifies minimum requirements for powered Respiratory Protective Devices (RPD) incorporating a tight-fitting respiratory interface. It does not cover devices designed for use in circumstances where there is or might be an oxygen deficiency.
Escape RPD and filters for use against CO are not covered by this document.
Laboratory tests and practical performance tests are included for the assessment of compliance with the requirements.

Atemschutzgeräte - Gebläsefiltergeräte mit Vollmaske, Halbmaske oder Viertelmaske - Anforderungen, Prüfung, Kennzeichnung

Dieses Dokument legt Mindestanforderungen an Atemschutzgeräte (ASG) mit Gebläse und einem Atem¬anschluss mit Dichtsitz fest. Es ist nicht anwendbar für Geräte, die für die Verwendung bei möglichem Sauerstoff-Mangel vorgesehen sind.
Fluchtgeräte (ASG zu Fluchtzwecken) und Filter zur Verwendung gegen CO werden von diesem Dokument nicht abgedeckt.
Laborprüfungen und praktische Leistungsprüfungen sind enthalten, um die Übereinstimmung mit den Anforderungen feststellen zu können.

Appareils de protection respiratoire - Appareils filtrants à ventilation assistée avec masques complets, demi-masques ou quarts de masques - Exigences, essais, marquage

Le présent document spécifie des exigences minimales applicables aux appareils de protection respiratoire (APR) intégrant une interface respiratoire à ajustement serré. Il ne traite pas des appareils conçus pour être utilisés dans des circonstances présentant ou susceptibles de présenter un défaut (manque) d’oxygène.
Les APR d’évacuation et les filtres spécifiques contre le monoxyde de carbone ne sont pas couverts par le présent document.
Il comporte des essais de laboratoire et des essais pratiques de performance pour évaluer la conformité aux exigences.

Oprema za varovanje dihal - Zaščitna obrazna, polobrazna ali četrtinska maska s tlačno filtracijo zraka - Zahteve, preskušanje, označevanje

Dokument določa minimalne zahteve za opremo za varovanje dihal (RPD) s tesno prilegajočim se vmesnikom za dihanje. Ne zajema naprav, ki so zasnovane za uporabo v okoliščinah, kjer obstaja ali se lahko pojavi pomanjkanje kisika.
Ta dokument ne zajema opreme za varovanje dihal za izhod v sili in filtrov za zaščito pred ogljikovimi oksidi.
Vključeni so tudi laboratorijski in praktični preskusi učinkovitosti za ocenjevanje skladnosti z zahtevami.

General Information

Status
Published
Publication Date
19-Dec-2023
Withdrawal Date
10-Apr-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Dec-2023
Due Date
26-Dec-2018
Completion Date
20-Dec-2023

Relations

Buy Standard

Standard
EN 12942:2024
English language
44 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2024
Nadomešča:
SIST EN 12942:1999
SIST EN 12942:1999/A1:2003
SIST EN 12942:1999/A2:2009
Oprema za varovanje dihal - Zaščitna obrazna, polobrazna ali četrtinska maska s
tlačno filtracijo zraka - Zahteve, preskušanje, označevanje
Respiratory protective devices - Powered filtering devices incorporating full face masks,
half masks or quarter masks - Requirements, testing, marking
Atemschutzgeräte - Gebläsefiltergeräte mit Vollmaske, Halbmaske oder Viertelmaske -
Anforderungen, Prüfung, Kennzeichnung
Appareils de protection respiratoire - Appareils filtrants à ventilation assistée avec
masques complets, demi-masques ou quarts de masques - Exigences, essais,
marquage
Ta slovenski standard je istoveten z: EN 12942:2023
ICS:
13.340.30 Varovalne dihalne naprave Respiratory protective
devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 12942
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2023
EUROPÄISCHE NORM
ICS 13.340.30 Supersedes EN 12942:1998
English Version
Respiratory protective devices - Powered filtering devices
incorporating full face masks, half masks or quarter masks
- Requirements, testing, marking
Appareils de protection respiratoire - Appareils Atemschutzgeräte - Gebläsefiltergeräte mit Vollmaske,
filtrants à ventilation assistée avec masques complets, Halbmaske oder Viertelmaske - Anforderungen,
demi-masques ou quarts de masques - Exigences, Prüfung, Kennzeichnung
essais, marquage
This European Standard was approved by CEN on 9 August 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12942:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions, description and symbols . 6
3.1 Terms and definitions . 6
3.2 Description . 7
3.3 Symbols . 7
4 Classification . 8
5 Requirements . 9
5.1 General . 9
5.2 Values and tolerances . 10
5.3 Ergonomics . 10
5.4 Design . 10
5.5 Materials . 10
5.6 Mechanical strength (optional) . 10
5.7 Resistance to temperature . 10
5.8 Respiratory interface (RI) . 11
5.9 Inward leakage . 13
5.10 Breathing resistance . 14
5.11 Air supply . 14
5.12 Warning facilities . 15
5.13 Electrical components . 15
5.14 Breathing hose, if applicable, and couplings . 15
5.15 Filters . 16
5.16 Noise level . 21
5.17 Carbon dioxide content of the inhalation air . 22
5.18 Flammability . 22
5.19 Mass of RPD . 22
5.20 Practical performance . 23
6 Testing . 23
6.1 Test schedule . 23
6.2 Conditioning . 25
6.3 Inspection . 25
6.4 Inward leakage . 26
6.5 Breathing resistance . 27
6.6 Manufacturer's minimum design duration. 27
6.7 Air supply flow rate . 28
6.8 Resistance to collapse of breathing hose . 30
6.9 Strength of hose and couplings . 31
6.10 Interactive flow rate . 31
6.11 Mechanical strength . 33
6.12 Filter performance testing . 34
6.13 Mass carried by the head . 38
7 Marking . 38
7.1 General . 38
7.2 RI . 38
7.3 Blower unit and battery casing (if separate from the blower) . 38
7.4 Filters . 39
7.5 Filter package . 40
7.6 RPD packages . 40
8 Information supplied by the manufacturer . 40
8.1 Complete RPD . 40
8.2 Filters . 41
Annex ZA (informative) Relationship between this European Standard and the essential
health and safety requirements of Regulation 2016/425/EU [2016 OJ L81] aimed to
be covered . 42
Bibliography . 44
European foreword
This document (EN 12942:2023) has been prepared by Technical Committee CEN/TC 79 “Respiratory
protective devices”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2024 and conflicting national standards shall be
withdrawn at the latest by June 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12942:1998.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
The following main technical changes have been made compared to EN 12942:1998:
a) Clause 4 Designation was deleted;
b) number of test samples was added to the requirements, where necessary;
c) classification table was amended to cover Hg and NO filter for all classes (TM1, TM2 and TM3);
d) nominal values and tolerances were added;
e) clogging was deleted;
f) warning facilities were amended to cover low energy and low flow warning;
g) visual inspection was changed to inspection and detailed list inserted;
h) test substances and number of test subjects for inward leakage test was changed;
i) test for noise level was adapted to the test procedure specified in ISO 16900-14:2020;
j) Annex A was deleted;
k) figures were adapted to the changes made in the test procedures, where appropriate.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of N
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.