FprEN 13245-3:2025
(Main)Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 3: Designation of PVC-UE profiles
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 3: Designation of PVC-UE profiles
This document establishes a system of designation for profiles made of cellular unplasticized poly(vinyl chloride) (PVC-UE) intended to be used for building applications. This system is intended to be used in product specification after the application is specified.
NOTE It is intended to use this method for the designation of PVC-UE profiles for information related to technical literature of the manufacturer, not for the marking of the products.
This part is applicable to PVC-UE profiles of any colour, obtained by a mono-extrusion or a co-extrusion process, with or without surface finishing (e.g. foil, paint or print).
This document defines minimum requirements for the surface finishing of PVC-UE profiles.
Profiles for the management of electrical power cables, communication cables and power track systems used for the distribution of electrical power, profiles for windows or doors and profiles for guttering are not covered by this document.
Kunststoffe – Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) für die Anwendung im Bauwesen – Teil 3: PVC-UE-Profilen
Dieses Dokument legt ein System zur Bezeichnung von Profilen aus geschäumtem weichmacherfreien Poly
vinylchlorid (PVC-UE) für die Anwendung im Bauwesen fest. Dieses System ist für die Verwendung bei der Produktspezifikation vorgesehen, nachdem die Anwendung festgelegt ist.
ANMERKUNG Es ist vorgesehen, dieses Verfahren zur Bezeichnung von PVC-U-Profilen für Informationen in den technischen Unterlagen des Herstellers und nicht zur Kennzeichnung der Produkte zu verwenden.
Dieser Teil ist anwendbar für durch ein Mono-extrusions- oder ein Ko-extrusionsverfahren erhaltene PVC-UE- Profile jeglicher Farbe mit oder ohne Oberflächenveredelung (z.B. Folie, Lack oder Druck).
Dieses Dokument legt Mindestanforderungen an die Oberflächenveredelung von PVC-UE-Profilen fest.
Profile für die Führung elektrischer Stromkabel, Datenkabel und Stromschienen für die Verteilung von elek
trischem Strom, Fenster- oder Türprofile und Profile für Dachrinnen werden durch dieses Dokument nicht abgedeckt.
Plastiques - Profilés en poly(chlorure de vinyle) non plastifié (PVC-U) pour applications dans le bâtiment - Partie 3 : Désignation des profilés en PVC-UE
Dieses Dokument legt ein System zur Bezeichnung von Profilen aus geschäumtem weichmacherfreien Poly
vinylchlorid (PVC-UE) für die Anwendung im Bauwesen fest. Dieses System ist für die Verwendung bei der Produktspezifikation vorgesehen, nachdem die Anwendung festgelegt ist.
ANMERKUNG Es ist vorgesehen, dieses Verfahren zur Bezeichnung von PVC-U-Profilen für Informationen in den technischen Unterlagen des Herstellers und nicht zur Kennzeichnung der Produkte zu verwenden.
Dieser Teil ist anwendbar für durch ein Mono-extrusions- oder ein Ko-extrusionsverfahren erhaltene PVC-UE- Profile jeglicher Farbe mit oder ohne Oberflächenveredelung (z.B. Folie, Lack oder Druck).
Dieses Dokument legt Mindestanforderungen an die Oberflächenveredelung von PVC-UE-Profilen fest.
Profile für die Führung elektrischer Stromkabel, Datenkabel und Stromschienen für die Verteilung von elek
trischem Strom, Fenster- oder Türprofile und Profile für Dachrinnen werden durch dieses Dokument nicht abgedeckt.
Polimerni materiali - Profili iz nemehčanega polivinilklorida (PVC-U) za uporabo v gradbeništvu - 3. del: Označevanje profilov PVC-UE
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 13245-3:2024
01-september-2024
Polimerni materiali - Profili iz nemehčanega polivinilklorida (PVC-U) za uporabo v
gradbeništvu - 3. del: Označevanje profilov PVC-UE
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications -
Part 3: Designation of PVC-UE profiles
Kunststoffe - Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) für die
Anwendung im Bauwesen - Teil 3: Bezeichnung von Profilen aus PVC-UE
Plastiques - Profilés en poly(chlorure de vinyle) non plastifié (PVC-U) pour applications
dans le bâtiment - Partie 3 : Désignation des profilés en PVC-UE
Ta slovenski standard je istoveten z: prEN 13245-3
ICS:
83.140.99 Drugi izdelki iz gume in Other rubber and plastics
polimernih materialov products
oSIST prEN 13245-3:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 13245-3:2024
oSIST prEN 13245-3:2024
DRAFT
EUROPEAN STANDARD
prEN 13245-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2024
ICS 83.140.99 Will supersede EN 13245-3:2010
English Version
Plastics - Unplasticized poly(vinyl chloride) (PVC-U)
profiles for building applications - Part 3: Designation of
PVC-UE profiles
Plastiques - Profilés en poly(chlorure de vinyle) non Kunststoffe - Profile aus weichmacherfreiem
plastifié (PVC-U) pour applications dans le bâtiment - Polyvinylchlorid (PVC-U) für die Anwendung im
Partie 3 : Désignation des profilés en PVC-UE Bauwesen - Teil 3: Bezeichnung von Profilen aus PVC-
UE
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13245-3:2024 E
worldwide for CEN national Members.
oSIST prEN 13245-3:2024
prEN 13245-3:2024 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Designation of PVC-UE profiles . 8
5 Codification system for Data block 3 to Data block 5 . 8
5.1 Modulus of elasticity in flexure (Data block 3) . 8
5.2 Nominal linear mass (Data block 4) . 9
5.3 Heat reversion at 75 °C (Data block 4) . 9
5.4 Impact resistance (Data block 4) . 9
5.5 Durability (Data block 5) . 10
5.5.1 General . 10
5.5.2 Test methods for ageing . 10
5.5.3 Methods for assessing of ageing. 12
5.5.4 Codification for properties after ageing . 13
6 Required characteristics for Type 3 and Type 4 and Type 5 profiles . 16
7 Optional characteristics. 16
7.1 Resistance to staining . 16
7.2 Application and appearance of the surface finishing (only for Type 3, Type 4 and
Type 5 profiles) . 17
7.2.1 General . 17
7.2.2 Single colour profiles . 17
7.2.3 Non-uniform colour and texture profiles . 17
7.2.4 Gloss . 17
8 Example of the designation of a PVC-UE profile . 17
9 Use of rPVC-U or IRM . 18
10 Design for recycling . 18
Annex A (normative) Determination of the linear mass . 19
A.1 Apparatus . 19
A.2 Test specimens . 19
A.3 Procedure. 19
A.4 Calculation and expression of results . 19
Annex B (normative) Falling weight impact resistance of PVC-UE profiles . 20
B.1 Principle . 20
B.2 Apparatus . 20
B.3 Test specimens . 21
B.4 Conditioning . 21
B.4.1 Impact resistance at 23 °C . 21
oSIST prEN 13245-3:2024
prEN 13245-3:2024 (E)
B.4.2 Impact resistance at low temperature . 22
B.5 Procedure . 22
B.6 Expression of results . 22
Annex C (normative) Determination of peel strength using a constant-load tensile test . 24
C.1 Principle . 24
C.2 Apparatus . 24
C.3 Preparation of test pieces . 24
C.4 Conditioning . 25
C.5 Procedure for constant-load tensile test . 25
C.6 Test report . 25
Bibliography . 27
oSIST prEN 13245-3:2024
prEN 13245-3:2024 (E)
European foreword
This document (prEN 13245-3:2024) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by SIS.
This document is currently submitted to CEN Enquiry.
This document will supersede EN 13245-3:2010.
EN 13245, Plastics ― Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications, consists
of the following parts:
— Part 1: Designation of PVC-U profiles
— Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes
— Part 3: Designation of PVC-UE profiles
oSIST prEN 13245-3:2024
prEN 13245-3:2024 (E)
1 Scope
This document establishes a system of designation for profiles made of cellular unplasticized poly(vinyl
chloride) (PVC-UE) intended to be used for building applications.
This part is applicable to light coloured and coloured mono-extruded PVC-UE profiles, co-extruded
profiles consisting of a core made of PVC-UE and a skin layer of non-cellular unplasticized poly(vinyl
chloride) (PVC-U), and PVC-UE profiles with laminated foil or paint.
It specifies test methods and test parameters.
This method of designation is intended to be used in product specification when the application is
specified.
Profiles for the management of electrical power cables, communication cables and power track systems
used for the distribution of electrical power, profiles for windows or doors and profiles for guttering are
not covered by this document .
NOTE It is intended to use this method for the designation of PVC-UE profiles for information related to
technical literature of the manufacturer, not for the marking of the products.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 438-2:2016+A1:2018, High-pressure decorative laminates (HPL) — Sheets based on thermosetting
resins (usually called Laminates) — Part 2: Determination of properties
EN 477, Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of
profiles by falling mass
EN 478, Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the appearance after exposure
at 150 °C
EN 479, Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion
EN 513, Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to artificial
weathering
EN 17271, Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the peel strength of profiles
laminated with foils
EN 17410, Plastics - Controlled loop recycling of PVC-U profiles from windows and doors
EN 17508, Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and
doors - Terminology of PVC based materials
EN 17615, Plastics - Environmental Aspects - Vocabulary
Profiles that are excluded are in the scopes of standards prepared by CEN/TC 249/WG 21, CENELEC/TC 213 or
CEN/TC 128.
oSIST prEN 13245-3:2024
prEN 13245-3:2024 (E)
EN 20105-A02, Textiles - Tests for colour fastness - Part A02: Grey scale for assessing change in colour (ISO
105-A02)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.