Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

This part of the EN 13523 series specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung mit Leuchtstofflampen und Kondensation von Wasser

Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV fluorescent et à la condensation de l'eau

Le présent document spécifie les principes de base et le mode opératoire à appliquer pour déterminer la résistance d’un revêtement organique appliqué sur un support métallique (prélaquage en bandes continues), à une combinaison d’un rayonnement UV fluorescent, de condensation d’eau et de température, dans des conditions contrôlées.
Compte tenu des diverses conditions qui règnent pendant le processus de vieillissement naturel et de la nature extrême des essais accélérés, aucune corrélation ne peut être escomptée entre les deux.
Tous les revêtements organiques ne se comporteront pas de la même manière, mais un certain degré de corrélation peut apparaître entre ceux de même type générique.

Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti fluorescentni ultravijolični svetlobi in kondenzaciji vode

General Information

Status
Published
Publication Date
23-Apr-2024
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
24-Apr-2024
Due Date
06-Aug-2025
Completion Date
24-Apr-2024

Relations

Buy Standard

Standard
EN 13523-10:2024
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2024
Nadomešča:
SIST EN 13523-10:2017
Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti
fluorescentni ultravijolični svetlobi in kondenzaciji vode
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and
water condensation
Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung
mit Leuchtstofflampen und Kondensation von Wasser
Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV
fluorescent et à la condensation de l'eau
Ta slovenski standard je istoveten z: EN 13523-10:2024
ICS:
17.180.20 Barve in merjenje svetlobe Colours and measurement of
light
25.220.60 Organske prevleke Organic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13523-10
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2024
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-10:2017
English Version
Coil coated metals - Test methods - Part 10: Resistance to
fluorescent UV radiation and water condensation
Tôles prélaquées - Méthodes d'essai - Partie 10 : Bandbeschichtete Metalle - Prüfverfahren - Teil 10:
Résistance à un rayonnement UV fluorescent et à la Beständigkeit gegen UV-Strahlung mit
condensation de l'eau Leuchtstofflampen und Kondensation von Wasser
This European Standard was approved by CEN on 1 January 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-10:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus and materials . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure . 6
8.1 Exposure . 6
8.2 Calibration and maintenance of calibration . 7
8.3 Evaluation of test specimens . 7
9 Expression of results . 8
10 Precision . 8
11 Test report . 8
Bibliography . 9

European foreword
This document (EN 13523-10:2024) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2024, and conflicting national standards shall
be withdrawn at the latest by October 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-10:2017.
10:2017:
a) in 8.1 the test duration has been aligned with EN 1396 and EN 10169;
b) in 8.3 wider range of observations have been included;
c) in Clause 9 the test method has been aligned to new coating categories defined in EN 10169;
d) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Ro
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.