EN 13523-29:2024

SLOVENSKI STANDARD
oSIST prEN 13523-29:2023
01-september-2023
Prevlečene kovine, ki se navijajo - Preskusne metode - 29. del: Odpornost proti
onesnaženju iz okolja (nabiranje nesnage in nastanek prog)
Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt
pick-up and striping)
Bandbeschichtete Metalle - Prüfverfahren - Teil 29: Beständigkeit gegen Verschmutzung
(Schmutzaufnahme und Streifenbildung)
Tôles prélaquées - Méthodes d'essai - Partie 29 : Résistance à la pollution
environnementale (salissures)
Ta slovenski standard je istoveten z: prEN 13523-29
ICS:
13.020.40 Onesnaževanje, nadzor nad Pollution, pollution control
onesnaževanjem in and conservation
ohranjanje
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-29:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 13523-29:2023
oSIST prEN 13523-29:2023
DRAFT
EUROPEAN STANDARD
prEN 13523-29
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2023
ICS 25.220.60 Will supersede EN 13523-29:2017
English Version
Coil coated metals - Test methods - Part 29: Resistance to
environmental soiling (Dirt pick-up and striping)
Tôles prélaquées - Méthodes d'essai - Partie 29 : Bandbeschichtete Metalle - Prüfverfahren - Teil 29:
Résistance à la pollution environnementale (salissures) Beständigkeit gegen Verschmutzung
(Schmutzaufnahme und Streifenbildung)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-29:2023 E
worldwide for CEN national Members.

oSIST prEN 13523-29:2023
prEN 13523-29:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus and materials . 5
6 Sample preparation . 6
7 Procedure . 6
8 Evaluation . 7
9 Test report . 8
Bibliography . 9
oSIST prEN 13523-29:2023
prEN 13523-29:2023 (E)
European foreword
This document (prEN 13523-29:2023) has been prepared by Technical Committee CEN/TC 139 “Paints
and varnishes”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13523-29:2017.
In comparison with the previous edition, the following technical modifications have been made:
a) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
oSIST prEN 13523-29:2023
prEN 13523-29:2023 (E)
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— P
...