ASTM F1216-09

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F 1216–08 Designation:F 1216–09
Standard Practice for
Rehabilitation of Existing Pipelines and Conduits by the
,
1 2
Inversion and Curing of a Resin-Impregnated Tube
This standard is issued under the fixed designation F 1216; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This practice describes the procedures for the reconstruction of pipelines and conduits (4 to 108-in. diameter) by the
installation of a resin-impregnated, flexible tube which is inverted into the existing conduit by use of a hydrostatic head or air
pressure.Theresiniscuredbycirculatinghotwaterorintroducingcontrolledsteamwithinthetube.Whencured,thefinishedpipe
will be continuous and tight-fitting.This reconstruction process can be used in a variety of gravity and pressure applications such
as sanitary sewers, storm sewers, process piping, electrical conduits, and ventilation systems.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. For specific precautionary statements, see 7.4.2.
2. Referenced Documents
3
2.1 ASTM Standards:
D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D903 Test Method for Peel or Stripping Strength of Adhesive Bonds
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3567 Practice for Determining Dimensions of Fiberglass (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D3839 Guide for Underground Installation of Fiberglass (Glass-FiberReinforced Thermosetting-Resin) Pipe
D5813 Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
E797 Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method
F412 Terminology Relating to Plastic Piping Systems
2.2 AWWA Standard:
4
Manual on Cleaning and Lining Water Mains, M 28
2.3 NASSCO Standard:
5
Recommended Specifications for Sewer Collection System Rehabilitation
3. Terminology
3.1 DefinitionsareinaccordancewithTerminologyF412andabbreviationsareinaccordancewithTerminologyD1600,unless
otherwise specified.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 cured-in-place pipe (CIPP)—a hollow cylinder containing a nonwoven or a woven material, or a combination of
nonwoven and woven material surrounded by a cured thermosetting resin. Plastic coatings may be included. This pipe is formed
1
This practice is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 onTrenchless Plastic
Pipeline Technology .
Current edition approved Nov.March 1, 2008.2009. Published November 2008.March 2009. Originally approved in 1989. Last previous edition approved 20072008 as
F1216–07b.F1216–08.
2
The following report has been published on one of the processes: Driver, F. T., and Olson, M. R., “ Demonstration of Sewer Relining by the Insituform Process,
Northbrook, Illinois,” EPA-600/2-83-064, Environmental Protection Agency, 1983. Interested parties can obtain copies from the Environmental Protection Agency or from
a local technical library.
3
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Water Works Association (AWWA), 6666 W. Quincy Ave., Denver, CO 80235, http://www.awwa.org.
5
Available from the National Association of Sewer Service Companies, 101 Wymore Rd., Suite 501, Altamonte, FL 32714.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

-----------
...