ASTM F2169-12
(Specification)Standard Specification for Resilient Stair Treads
Standard Specification for Resilient Stair Treads
ABSTRACT
This specification covers resilient stair treads made of rubber and thermoplastic vinyl for interior use. Treads covered by this specification includes the following types, class, and groups: Type TS, Type TP, Type TV, Class 1, Class 2, Group 1, and Group 2. The material requirements for the tread surface design, nosing style, and color are specified. Some typical nosing styles are illustrated. Treads shall meet the specified performance requirements for: (1) hardness, (2) molded stair tread bonding surface, (3) tread backs, (4) resistance to chemicals for short-term exposure, (5) resistance to heat, and (6) resistance to light. The prescribed dimensional requirements includes tread thickness, length, and depth. The sampling methods for the physical property tests are specified.
SCOPE
1.1 This specification covers resilient treads made of rubber and vinyl for interior use.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2169 −12
StandardSpecification for
1
Resilient Stair Treads
This standard is issued under the fixed designation F2169; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.3 ANSI Standard:
ANSI/ASQC Z1.4-2003 Sampling Procedures and Tables
1.1 This specification covers resilient treads made of rubber
3
for Inspection by Attributes
and vinyl for interior use.
3. Terminology
1.2 The values stated in inch-pound units are to be regarded
3.1 Material Definitions:
as the standard. The values given in parentheses are for
3.1.1 rubber, thermoplastic—The polymeric binder of this
information only.
compound shall satisfy the definition of rubber, but remain
1.3 This standard does not purport to address all of the
thermoplastic, as defined in Terminology D883.
safety concerns, if any, associated with its use. It is the
3.1.2 rubber, vulcanized thermoset—thepolymericbinderof
responsibility of the user of this standard to establish appro-
this compound shall satisfy the definition of rubber, and have
priate safety and health practices and determine the applica-
been vulcanized, as defined in Terminology D1566.
bility of regulatory requirements prior to use.
3.1.3 vinyl, thermoplastic—The polymeric binder of this
compoundshallsatisfythedefinitionofpoly(vinylchloride)in
2. Referenced Documents
Terminology D883 and Specification D1755 but remain ther-
2.1 The following documents of the issue in effect on the moplastic as defined in Terminology D883.
dateofthematerialpurchaseformapartofthisspecificationto
4. Classification
the extent referenced herein:
4.1 Treads covered by this specification will be of the
2
2.2 ASTM Standards:
following types (compositions), class, groups and grades as
D883 Terminology Relating to Plastics
specified.
D1566 Terminology Relating to Rubber
Type TS Rubber, Vulcanized Thermoset
D1755 Specification for Poly(Vinyl Chloride) Resins
Type TP Rubber, Thermoplastic
D2240 Test Method for Rubber Property—Durometer Hard- Type TV Vinyl, Thermoplastic
Class 1 Smooth (Flat)
ness
Class 2 Pattern: Embossed, Grooved, or Ribbed
F386 Test Method for Thickness of Resilient Flooring Ma-
Group 1 Abrasive Strips: Embedded
Group 2 Contrasting Color for Visually Impaired
terials Having Flat Surfaces
Grade – Based on Shore A durometer hardness:
F925 Test Method for Resistance to Chemicals of Resilient
Grade 1$ 85
Flooring Grade 2$ 70 but less than 85
F1514 TestMethodforMeasuringHeatStabilityofResilient
5. Ordering Information
Flooring by Color Change
F1515 Test Method for Measuring Light Stability of Resil- 5.1 Purchasers shall state whether this specification is to be
used, select the preferred options permitted herein, and include
ient Flooring by Color Change
the following information in the invitation to bid or purchase
order:
5.1.1 Title, number, and date of this specification.
1
This specification is under the jurisdiction of ASTM Committee F06 on
5.1.2 Type, class, nosing style (see Sections 4 and 6).
Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.80
on Specifications. 5.1.3 Color (see 6.4).
Current edition approved May 15, 2012. Published June 2012. Originally
5.1.4 Quantity, in pieces, linear feet, or cartons.
approved in 2002. Last previous edition approved in 2008 as F2169-02(2008). DOI:
5.1.5 Thickness required (see 8.2).
10.1520/F2169-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute, 25 W. 43rd St., 4th
the ASTM website. Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2169−12
5.1.6 Length required (see 8.3).
5.1.7 Lot information, if other than as specified in ANSI/
ASQC Z1.4-2003 (see 10.1 and 11.1).
5.1.8 Sampling, if other than as specified in ANSI/ASQC
Z1.4-2003 (see 10.1).
FIG. 2Square Nose
5.1.9 Statement requesting certification, if certification of
compliance is required (see Section 12).
5.1.10 Packing requirement, if other than as specified (see
Section 14).
5.1.11 Palletization, if required.
5.1.12 Markingrequired,ifotherthanspecified(seeSection
13).
5.1.13 Other requirements.
6. Materials and Manufacture
6.1 Standard Commercial Product—A tread of the same
classification shall, as a minimum, be in accordance with the
requirements of this specification and shall be the manufact
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F2169–02 (Reapproved 2008) Designation: F2169 – 12
Standard Specification for
1
Resilient Stair Treads
This standard is issued under the fixed designation F2169; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers resilient treads made of rubber and vinyl for interior use.
1.2 Thevaluesstatedininch-poundunitsaretoberegardedasthestandard.Thevaluesgiveninparenthesesareforinformation
only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
requirements prior to use.
2. Referenced Documents
2.1 The following documents of the issue in effect on the date of the material purchase form a part of this specification to the
extent referenced herein:
2
2.2 ASTM Standards:
D883 Terminology Relating to Plastics
D1566 Terminology Relating to Rubber
D1755 Specification for Poly(Vinyl Chloride) Resins
D2240 Test Method for Rubber PropertyDurometer Hardness
F386 Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces
F925 Test Method for Resistance to Chemicals of Resilient Flooring
F1514 Test Method for Measuring Heat Stability of Resilient Flooring by Color Change
F1515 Test Method for Measuring Light Stability of Resilient Flooring by Color Change
2.3 ANSI Standard:
3
ANSI/ASQC Z1.4-2003 Sampling Procedures and Tables for Inspection by Attributes
3. Terminology
3.1 Material Definitions:
3.1.1 rubber, thermoplastic—The polymeric binder of this compound shall satisfy the definition of rubber, but remain
thermoplastic, as defined in Terminology D883.
3.1.2 rubber, vulcanized thermoset—the polymeric binder of this compound shall satisfy the definition of rubber, and have been
vulcanized, as defined in Terminology D1566.
3.1.3 vinyl, thermoplastic—The polymeric binder of this compound shall satisfy the definition of poly (vinyl chloride) in
Terminology D883 and Specification D1755 but remain thermoplastic as defined in Terminology D883.
4. Classification
4.1 Treads covered by this specification will be of the following types (compositions), class, groups and groups,grades as
specified.
Type TS Rubber, Vulcanized Thermoset
Type TP Rubber, Thermoplastic
1
This specification is under the jurisdiction of ASTM Committee F06 on Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.80 on
Specifications.
Current edition approved March 1, 2008. Published April 2008. Originally approved in 2002. Last previous edition approved in 2002 as F2169-02. DOI:
10.1520/F2169-02R08.
Current edition approved May 15, 2012. Published June 2012. Originally approved in 2002. Last previous edition approved in 2008 as F2169-02(2008). DOI:
10.1520/F2169-12.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute, 25 W. 43rd St., 4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2169 – 12
Type TV Vinyl, Thermoplastic
Class 1 Smooth (Flat)
Pattern: Embossed, Grooved,
Class 2
or Ribbed
Group 1 Abrasive Strips: Embedded
Contrasting Color for Visually
Group 2
Impaired
Based on Shore A durometer
Grade –
hardness:
Grade 1$ 85
Grade 2$ 70 but less than
85
5. Ordering Information
5.1 Purchasers shall state whether this specification is to be used, select the preferred options permitted herein, and include the
following information in the invitation to bid or purchase order:
5.1.1 Title, number, and date of this specification.
5.1.2 Type, class, nosing style (see Sections 4 and 6).
5.1.3 Color (see 6.4).
5.1.4 Quantity, in pieces, linear feet, or cartons.
5.1.5 Thickness required (see 8.2).
5.1.6 Length required (see 8.3).
5.1.7 Lot information, if other than as specified in ANSI/ASQC Z1.4-2003 (see 10.1 and 11.1).
5.1.8 Sampling, if other than as specified in ANSI/ASQC Z1.4-2003 (see 10.1).
5.1.9 Statement reques
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.