ASTM F824-22
(Specification)Standard Specification for Tables, Mess, Marine, Steel
Standard Specification for Tables, Mess, Marine, Steel
ABSTRACT
This specification covers the construction of round, square, and rectangular marine mess tables with or without adjustable lee rails for use in crew, officer, and passenger dining areas aboard ship. These tables are classified into three types. Type I shall be a round mess table with a single pedestal, Type II is a square mess table with a single pedestal and Type III is a rectangular mess table. Type III table may be designated according to the number of pedestals it contains: Grade 1 with single pedestal and Grade 2 with two pedestals. These tables can also be designated into two classes: Class 1 has fixed lee rails and Class 2 has adjustable lee rails. Table tops shall be steel construction with a decorative melamine laminate top cover. Other materials or components of the table shall include lee rails, edge binders, pedestals, and support plate. Joining of metal components shall be done by welding or gluing with a structural adhesive. Tops for mess tables shall be capable of supporting a load of a certain kilogram uniformly distributed over an area of determined and placed at any location on the top. Load shall remain on top for a certain minimum time, and there shall be no indication of permanent set after removal of load.
SCOPE
1.1 This specification covers the construction of round, square, and rectangular marine mess tables with or without adjustable lee rails for use in crew, officer, and passenger dining areas aboard ship.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F824 −22 An American National Standard
Standard Specification for
1
Tables, Mess, Marine, Steel
ThisstandardisissuedunderthefixeddesignationF824;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A501 Specification for Hot-Formed Welded and Seamless
Carbon Steel Structural Tubing
1.1 This specification covers the construction of round,
A1011/A1011M Specification for Steel, Sheet and Strip,
square, and rectangular marine mess tables with or without
Hot-Rolled, Carbon, Structural, High-Strength Low-
adjustable lee rails for use in crew, officer, and passenger
Alloy, High-Strength Low-Alloy with Improved
dining areas aboard ship.
Formability, and Ultra-High Strength
1.2 The values stated in inch-pound units are to be regarded
A582/A582M Specification for Free-Machining Stainless
as standard. The values given in parentheses are mathematical
Steel Bars
conversions to SI units that are provided for information only
B221 Specification forAluminum andAluminum-Alloy Ex-
and are not considered standard.
truded Bars, Rods, Wire, Profiles, and Tubes
1.3 This international standard was developed in accor-
D907 Terminology of Adhesives
4
dance with internationally recognized principles on standard-
2.2 NEMA Specification:
ization established in the Decision on Principles for the
NEMA LD-3 High Pressure Decorative Laminates
5
Development of International Standards, Guides and Recom-
2.3 AISC Manual:
mendations issued by the World Trade Organization Technical
AISCWireandSheetMetalGauges EquivalentThicknessin
Barriers to Trade (TBT) Committee.
Decimals of an Inch, U.S. Standard Gauge (USSG) for
Uncoated Hot and Cold Rolled Sheets
2. Referenced Documents
2
3. Terminology
2.1 ASTM Standards:
A53/A53M Specification for Pipe, Steel, Black and Hot-
3.1 Definitions of Terms Specific to This Standard:
Dipped, Zinc-Coated, Welded and Seamless
3.1.1 mess table—a dining table for use in crew, officer, or
A167 Specification for Stainless and Heat-Resisting
passenger dining areas, consisting of a horizontal top assembly
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
and one or more supporting pedestals.
3
drawn 2014)
3.1.2 table top—the assembled horizontal surface of the
A240/A240M Specification for Chromium and Chromium-
mess table including the substrate, top covering, lee rails, and
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
edge binder, or all of the preceding.
Vessels and for General Applications
3.1.2.1 substrate—the structural core of the top assembly.
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled,
3.1.2.2 top covering—the decorative melamine laminate
Carbon, Structural, High-Strength Low-Alloy, High-
attached to the top surface of the substratae.
Strength Low-Alloy with Improved Formability, Required
Hardness, Solution Hardened, and Bake Hardenable
3.1.2.3 lee rails:
A500 Specification for Cold-Formed Welded and Seamless
(1) fixed lee rail—a trim piece at the edge of the table top
Carbon Steel Structural Tubing in Rounds and Shapes
that projects above the upper surface of the table top to retain
tableware and act as an edge binder.
(2) adjustable lee rail—a trim piece at the edge of the table
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
top that can be raised above the upper surface of the table top
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
to retain tableware and can be retracted when not needed.
Outfitting and Deck Machinery.
Current edition approved April 1, 2022. Published April 2022. Originally
3.1.2.4 edge binder—the finishing strips of metal applied to
approved 1983. Last previous edition approved in 2017 as F824 – 93 (2017). DOI:
the edge of the table top.
10.1520/F0824-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from National Electrical Manufacturers Association (NEMA), 1300
the ASTM website. N. 17th St., Suite 900, Arlington, VA 22209, http://www.nema.org.
3 5
The last approved version of this historical standard is referenced on Available from American Institute of Steel Construction (AISC), 130 E.
www.astm.org. Randolph St., Suite 2000, Chicago, IL 60601-6219, http://www.aisc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken,
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F824 − 93 (Reapproved 2017) F824 − 22 An American National Standard
Standard Specification for
1
Tables, Mess, Marine, Steel
This standard is issued under the fixed designation F824; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the construction of round, square, and rectangular marine mess tables with or without adjustable lee
rails for use in crew, officer, and passenger dining areas aboard ship.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
3
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A366/A366MA1008/A1008M Specification for Commercial Steel (CS) Sheet, Carbon, (0.15 Maximum Percent) Cold-
RolledSteel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved
Formability, Required Hardness, Solution Hardened, and Bake Hardenable (Withdrawn 2000)
A500 Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes
A501 Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing
A567/A567MA1011/A1011M Specification for Castings, Iron, Cobalt, and Nickel-Base Alloy, for High Strength at Elevated
TemperaturesSteel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy
with Improved Formability, and Ultra-High Strength (Withdrawn 1987)
A582/A582M Specification for Free-Machining Stainless Steel Bars
B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
D907 Terminology of Adhesives
4
2.2 NEMA Specification:
NEMA LD-3 High Pressure Decorative Laminates
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
Current edition approved Jan. 1, 2017April 1, 2022. Published January 2017April 2022. Originally approved 1983. Last previous edition approved in 20102017 as
F824 – 93 (2010).(2017). DOI: 10.1520/F0824-93R17.10.1520/F0824-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from National Electrical Manufacturers Association (NEMA), 1300 N. 17th St., Suite 900, Arlington, VA 22209, http://www.nema.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F824 − 22
5
2.3 AISC Manual:
AISC Wire and Sheet Metal Gauges Equivalent Thickness in Decimals of an Inch, U.S. Standard Gauge (USSG) for Uncoated
Hot and Cold Rolled Sheets
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 mess table—a dining table for use in crew, officer, or passenger dining areas, consisting of a horizontal top assembly and
one or more supporting pedestals.
3.1.2 table top—the assembled horizontal surface of the mess table including the substrate, top covering, lee rails, and edge binder,
or all of the preceding.
3.1.2.1 substrate—the structural core of the top assembly.
3.1.2.2 top covering—the decorative melamine laminate attached to the top surface of the substratae.
3.1.2.3 lee rails:
(1) fixed lee rail—a trim piece at the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.