iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E2462-10

(Specification)

Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I

Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I

SCOPE
1.1 Scope—This specification covers the performance requirements for the Type I Cargo Bed Cover (CBC). The Type I Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M1152A1, M1152A1 with B2 Armor Kit, M1037, M1042, M1097, and M1113 High-Mobility Multipurpose Wheeled Vehicle (HMMWV). The Type I CBC provides environmental protection and security for mission equipment and items of general transport.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Oct-2010
ICS
55.180.99 - Other standards related to freight distribution of goods
Technical Committee
E06 - Performance of Buildings
Drafting Committee
E06.53 - Materials and Processes for Durable Rigidwall Relocatable Structures
Current Stage
Ref Project

Relations

Replaces
ASTM E2462-05 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
Effective Date
01-Nov-2010
Replaced By
ASTM E2462-18 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
Effective Date
01-Oct-2018

Buy Standard

ASTM E2462-10 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type IASTM E2462-10 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
PreviousNext
Technical specification
ASTM E2462-10 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E2462-10 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type IREDLINE ASTM E2462-10 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
PreviousNext
Technical specification
REDLINE ASTM E2462-10 - Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E2462 −10
Standard Performance Specification for
1
Cargo Bed Cover (CBC) HMMWV, Type I
This standard is issued under the fixed designation E2462; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.3 Commercial Standards:
ANSI/ASQCZ1.4-2003 Sampling Procedures and Tables
1.1 Scope—This specification covers the performance re-
4
for Inspection by Attributes
quirementsfortheTypeICargoBedCover(CBC).TheTypeI
SAE AS8090 Mobility, Towed Aerospace Ground
Cargo Bed Cover is a removable general purpose rigid enclo- 5
Equipment, General Requirements for
sure for the cargo bed of the M1152A1, M1152A1 with B2 6
2.4 Federal Standard:
Armor Kit, M1037, M1042, M1097, and M1113 High-
FED-STD-595Colors Used in Government Procurement
Mobility Multipurpose Wheeled Vehicle (HMMWV). The
6
2.5 Military Standards:
TypeICBCprovidesenvironmentalprotectionandsecurityfor
MIL-STD-129Military Marking For Shipment and Storage
mission equipment and items of general transport.
MIL-STD-209Interface Standard for Lifting and Tie-down
Provisions
1.2 The values stated in SI units are to be regarded as
MIL-STD-810Environmental Engineering Considerations
standard. The values given in parentheses are mathematical
and Laboratory Tests
conversions to inch-pound units that are provided for informa-
MIL-STD-913Requirements for the Certification of Sling
tion only and are not considered standard.
Loaded Military Equipment for External Transportation
1.3 The following safety hazards caveat pertains only to the
by Department of Defense Helicopters
test required portion, Section 4, of this specification. This
MIL-STD-1366Transportability Criteria
standard does not purport to address all of the safety concerns,
MIL-PRF-22750Coating, Epoxy, High Solids
if any, associated with its use. It is the responsibility of the user MIL-C-46168Coating, Aliphatic Polyurethane, Chemical
of this standard to establish appropriate safety and health Agent Resistant
MIL-C-53039 Coating, Aliphatic Polyurethane, Single
practices and determine the applicability of regulatory limita-
Component, Chemical Agent Resistant
tions prior to use.
MIL-DTL-53072 Chemical Agent Resistant Coating
(CARC)SystemApplicationProceduresandQualityCon-
2. Referenced Documents
trol Inspection
2
2.1 ASTM Standards: 6
2.6 Military Handbook:
E1925Specification for Engineering and Design Criteria for
MIL-HDBK-1791Designing for InternalAerial Delivery in
Rigid Wall Relocatable Structures
Fixed Winged Aircraft
3
2.7 The American Conference of Governmental Industrial
2.2 Army Standards:
7
Hygienists (ACGIH):
ARMYTM9-2320-280-10HMMWV’S Operator’s Manual
ACGIH Threshold Limit Values
ARMYTM10-5411-231-13&PTechnical Manual
3
2.8 Drawings:
1
81337-103984Cargo Bed Cover, Type I (1 ⁄4 Ton HM-
MWV)
1
This specification is under the jurisdiction of ASTM Committee E06 on
Performance of Buildings and is the direct responsibility of Subcommittee E06.53
on Materials and Processes for Durable Rigidwall Relocatable Structures.
4
Current edition approved Nov. 1, 2010. Published December 2010. Originally Available fromAmerican Society for Quality (ASQ), 600 N. PlankintonAve.,
approved in 2005. Last previous edition approved in 2005 as E2462–05. DOI: Milwaukee, WI 53203, http://www.asq.org.
5
10.1520/E2462-10 AvailablefromSAEInternational(SAE),400CommonwealthDr.,Warrendale,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or PA 15096-0001, http://www.sae.org.
6
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. dodssp.daps.dla.mil.
3 7
Shelter Technology, Engineering & Fabrication Directorate, US Army Natick Available from American Conference of Governmental Industrial Hygienists,
Soldier RD&E Center, ATTN: RDNS-ST, Kansas Street, Natick, MA 01760-5018, Inc. (ACGIH), 1330 Kemper Meadow Dr., Cincinnati, OH 45240, http://
http://www.natick.army.mil. www.acgih.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E2462−10
1
81337-103984-101Cargo Bed Cover, Type I (1 ⁄4 Ton 3.2.6 Toxicity—Materialsusedshallcausenoskinirritations
HMMWV), Camouflage or other injuries and produce no vapor hazards, including the
emission of toxic or noxious odors, to personnel, in or around
3. General Requirements theType I CBC, unde
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E2462–05 Designation: E2462 – 10
Standard Performance Specification for
1
Cargo Bed Cover (CBC) HMMWV, Type I
This standard is issued under the fixed designation E2462; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 Scope—This specification covers the performance requirements for the Type I Cargo Bed Cover (CBC). The Type I Cargo
Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M1152A1, M1152A1 with B2 Armor Kit,
M1037, M1042, M1097, and M1113 High-Mobility Multipurpose Wheeled Vehicle (HMMWV). The Type I CBC provides
environmental protection and security for mission equipment and items of general transport.
1.2 The values stated in inch-pound units are to be regarded as the standard.The values given in parenthesis are for information
only. The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions
to inch-pound units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
E1925 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
3
2.2 Army Standards:
ARMY TM 9-2320-280-10 HMMWV’S Operator’s Manual
ARMY TM 10-5411-231-13&P Technical Manual
2.3 Commercial Standards:
4
ANSI/ASQC Z1.4-2003 Sampling Procedures and Tables for Inspection by Attributes
5
SAE AS8090 Mobility, Towed Aerospace Ground Equipment, General Requirements for
6
2.4 Federal Standard:
FED-STD-595 Colors Used in Government Procurement
6
2.5 Military Standards:
MIL-STD-129 Military Marking For Shipment and Storage
MIL-STD-209 Interface Standard for Lifting and Tie-down Provisions
MIL-STD-810 Environmental Engineering Considerations and Laboratory Tests
MIL-STD-913 Requirements for the Certification of Sling Loaded Military Equipment for External Transportation by
Department of Defense Helicopters
MIL-STD-1366 Transportability Criteria
MIL-PRF-22750 Coating, Epoxy, High Solids
MIL-C-46168 Coating, Aliphatic Polyurethane, Chemical Agent Resistant
1
This specification is under the jurisdiction ofASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.53 on Materials
and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Oct. 1, 2005. Published October 2005. DOI: 10.1520/E2462-05.
Current edition approved Nov. 1, 2010. Published December 2010. Originally approved in 2005. Last previous edition approved in 2005 as E2462 – 05. DOI:
10.1520/E2462-10
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from US Amy Natick Soldier Center, ATTN: AMSRD-NSC-CP-CS, Kansas Street, Natick,Ma 01760-5018.
3
Shelter Technology, Engineering & Fabrication Directorate, US Army Natick Soldier RD&E Center, ATTN: RDNS-ST, Kansas Street, Natick, MA 01760-5018,
http://www.natick.army.mil.
4
Available from American Society for Quality, 600 North Plankinton Ave., Milwaukee, WI 53203.
4
Available from American Society for Quality (ASQ), 600 N. Plankinton Ave., Milwaukee, WI 53203, http://www.asq.org.
5
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001.
5
Available from SAE International (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
6
Available from the Standardization Document Order Desk, 700 Robbins Ave, Building 4D, Philadelphia, PA 19111-5094.
6
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2463-19(Specification)
Standard Performance Specification for Cargo Bed Cover (CBC) M105A2 Trailer, Type II

SCOPE
1.1 This specification covers the general performance requirements for the Type II Cargo Bed Cover (CBC). The Type II Cargo Bed Cover is a removable general purpose rigid wall enclosure that is mounted on the M105A2 Trailer, Cargo: 1.5 Ton, 2 Wheel. The Type II CBC provides environmental protection and security for mission equipment and items of general transport.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parenthesis are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM E2462-18(Specification)
Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I

SCOPE
1.1 Scope—This specification covers the performance requirements for the Type I Cargo Bed Cover (CBC). The Type I Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M1152A1, M1152A1 with B2 Armor Kit, M1037, M1042, M1097, and M1113 High-Mobility Multipurpose Wheeled Vehicle (HMMWV). The Type I CBC provides environmental protection and security for mission equipment and items of general transport.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM D8134-18(2023)(Guide)
Standard Guide for Conducting Internal Hydrostatic Pressure Tests on United Nations (UN) IBC Design Types

SIGNIFICANCE AND USE
4.1 Dangerous goods (hazardous materials) regulations require performance tests to be conducted on packaging or IBC designs before being authorized for use. The regulations do not include standardized procedures for conducting performance tests and, because of this, may result in a non-uniform approach and differences in test results between testing facilities.  
4.2 The purpose of this standard is to provide guidance and to establish a set of common practices for conducting hydrostatic pressure tests on IBC designs subjected to UN certification testing.  
4.3 Intermediate bulk container designs are required to be tested in a sequence. This guide focuses on conducting the hydrostatic pressure test, which is preceded in the test sequence by the leakproofness test. The fittings and adaptors applied to the container for the hydrostatic pressure test may also be used for the leakproofness test.
SCOPE
1.1 This guide is intended to provide a standardized method and a set of basic instructions for performing hydrostatic pressure testing on Intermediate Bulk Containers (IBCs) designs as required by the United States Department of Transportation Title 49 Code of Federal Regulations (CFR) and the United Nations Recommendations on the Transport of Dangerous Goods (UN).  
1.2 This guide focuses on composite and rigid plastic IBCs and is suitable for testing IBCs of any design or material type.  
1.3 This guide provides information to help clarify various terms used as part of the United Nations (UN) certification process that may assist in determining the applicable test.  
1.4 This guide provides the suggested minimum information that should be documented when conducting pressure testing.  
1.5 This guide provides information for recommended equipment and fittings for conducting pressure tests.  
1.6 This guide is based on the current information contained in 49 CFR 178.814.  
1.7 When testing packaging designs intended for hazardous materials (dangerous goods), the user of this guide shall be trained in accordance with 49 CFR 172.700 and other applicable hazardous materials regulations such as the International Civil Aviation Organization (ICAO) Technical Instructions for the Safe Transport of Dangerous Goods by Air, the International Maritime Dangerous Goods Code (IMDG Code), and carrier rules such as the International Air Transport Association (IATA) Dangerous Goods Regulations.  
1.8 Units—”The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this guide.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM D6653/D6653M-13(2021)(Test Method)
Standard Test Methods for Determining the Effects of High Altitude on Packaging Systems by Vacuum Method

SIGNIFICANCE AND USE
4.1 Packaged products transported by meansn of the feeder aircraft network are liable to experience altitudes as high as 5 791 m [19 000 ft].4 When exposed to these high altitude conditions, products or packaging systems, or a combination thereof, may be affected negatively by the resultant pressure differential.  
4.2 These test methods are suitable for evaluating the effect of high altitude on packaging systems.  
4.3 These test methods are suitable for package or product, or both, development and engineering.  
4.4 Other test methods, such as Test Methods D3078, D4991 and D5094, test for leakage of packaging systems by vacuum method and are applicable for testing the effects of high altitude.
SCOPE
1.1 These test methods determine the effects of pressure differential when packaged products are transported by meansn of certain modes of transport, such as feeder aircraft or ground over high mountain passes. The results of these tests are intended to be used for qualitative purposes.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6179-20(Test Method)
Standard Test Methods for Rough Handling of Unitized Loads and Large Shipping Cases and Crates

SIGNIFICANCE AND USE
4.1 These test methods will allow the user to determine integrity and stability of the load as well as provide guidance to improve the design of the shipping container or the unit load where deficiencies are found.  
4.2 Damage to products or packages observed during testing can be expected to correlate at least in a qualitative way to damage observed in actual distribution handling systems.  
4.3 The results received from shock machine testing and free fall drop testing are different for certain products. Where this test is performed to satisfy a regulatory or contractual requirement, its use is subject to approval by the agency concerned.
SCOPE
1.1 These test methods cover testing the integrity of unitized loads and large shipping cases and crates as well as the ability of the contents to endure rough handling. Not all of the test methods are applicable to all products, containers, and loads. These test methods are applicable to common means of material handling as follows:  
1.1.1 Test Method A, B, C, D, and E—Drop Test—For measuring the ability of the case or crate or unitized load to withstand rough handling impacts and provide information useful in improving the design of the container. Normally, Test Methods A and B are not applied to unitized loads.  
1.1.2 Test Method F—Tip Test—For determining if filled tall or top heavy cases, crates, or unitized loads will tip over when tilted to a predetermined angle.  
1.1.3 Method G—Tipover Test—For determining the ability of filled large shipping cases or crates to resist the impacts associated with tipover hazards, and for determining the ability of the packaging and packing methods to provide protection to the contents, when the case or crate is tipped over.
Note 1: Test Method G fulfills the requirements of ISO 8768. ISO 8768 may not meet the requirements for Test Method G.  
1.1.4 Test Method H—Rolling Test—For determining the ability of complete, filled large shipping cases or crates to withstand the effects of rolling.
Note 2: Test Method H fulfills the requirements of ISO 2876. ISO 2876 may not meet the requirements for Test Method H.  
1.2 Additional Test Procedures:  
1.2.1 Test methods for mechanical handling of unitized loads and large shipping cases and crates are set forth in Test Method D6055. Additional tests that apply to mechanical handling of unitized loads and large cases and crates include incline impact tests, described in Test Method D880 and horizontal impact tests, described in Test Methods D4003 and Test Method D5277. Test Methods D4003 includes a special pallet marshaling test and Test Methods D1185 provides test methods for pallets and related structures.  
1.2.2 Practice D4169 provides a series of options for selecting and running performance tests on all types of shipping containers and systems.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5728-12(2020)(Practice)
Standard Practices for Securement of Cargo in Intermodal and Unimodal Surface Transport

SIGNIFICANCE AND USE
4.1 Numerous sources provide detailed information as to the loading, blocking, bracing, and unloading of specific types of cargo in unimodal and intermodal transport. Some of these sources are proprietary, others are massive and complex in scope, and none are consistently promulgated to shippers, carriers, and consignees. Many of the losses experienced by cargo in transport are due to the failure to practice proper basic cargo handling and loading techniques. These practices are intended to outline those techniques in simple, clear, generic, and easy to promulgate formats, including posters, slides, videotapes, and pamphlets, and are further intended to serve as the basis upon which a comprehensive cargo handling methodology may be built.  
4.2 Users of these practices should avail themselves of the detailed resource information available. The practices as defined are not sufficient to form a complete cargo handling protocol.
SCOPE
1.1 These practices are intended to serve as a guide to shippers, carriers, and consignees for load planning, loading, blocking, and bracing of intermodal and unimodal cargo in surface transport. The practices are referenced to a bibliography of information concerning the above. Hazardous materials, bulk cargo, non-containerized break bulk in ocean carriage, and transport of cargo by air are not included in these practices at this time.  
1.2 These practices shall apply to cargo in surface transport on flat bed, open top, box car, truck, van, and intermodal containers.  
1.3 The practices are intended to form a framework for the safe and effective loading and unloading of cargo in intermodal and unimodal surface transport. They are not intended to provide comprehensive detail relating to specific types of cargo, but will reference to source materials wherein such detail may be found.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D7387-20(Test Method)
Standard Test Method for Vibration Testing of Intermediate Bulk Containers (IBCs) Used for Shipping Liquid Hazardous Materials (Dangerous Goods)

SIGNIFICANCE AND USE
4.1 Shipping containers are exposed to complex dynamic stresses when subjected to vibration present in transportation vehicles. Approximating the actual damage, or lack of damage, experienced in shipping may require subjecting the container(s) and contents to vibration inputs.  
4.2 Resonant responses during shipment can be severe and may lead to failure of the container and spillage or leakage of contents. Identification of critical frequencies and the nature of package stresses can aid in minimizing the effect of these occurrences.  
4.3 This vibration test method is used for the qualification of IBCs in CFR 49 and has demonstrated successful use in transportation.  
4.4 Exposure to vibration can affect the shipping container, its means of closure, and its contents. This test method allows analysis of the interaction of these components. Design modification to one or more of these components may be utilized to achieve optimum performance in the shipping environment.  
4.5 This test method is suitable for individual filled containers that are transported unrestrained on the bed of a vehicle.  
4.6 This test method is not intended for testing intermediate bulk containers at a frequency that causes the container to go into resonance.
SCOPE
1.1 This test method covers vibration testing of filled intermediate bulk containers (IBCs) intended to contain liquid hazardous materials (dangerous goods) and is suitable for testing IBCs of any design or material type. This test method is required as part of the qualification of IBCs in accordance with the United States Department of Transportation Title 49 Code of Federal Regulations (CFR) and the United Nations Recommendations on the Transport of Dangerous Goods (UN).  
1.2 This test method is appropriate for testing IBCs ranging from 450 to 3000 L (119 to 793 gal). Packagings of smaller sizes should be tested using Test Method D999 or other applicable methods.  
1.3 The ISO 2247 standard may not meet the requirements for this test method.  
1.4 This test method is based on the current information contained in 49 CFR, §178.819.  
1.5 This test method is used to determine that the IBC maintains integrity and to prevent leakage or spillage of contents during shipping. This test method may also be used as a screening tool or as a design qualification test. Other vibration methods are available to more closely simulate vibration experienced in actual transportation.  
1.6 When testing packaging designs intended for hazardous materials (dangerous goods), the user of this test method shall be trained in accordance with 49 CFR §172.700 and other applicable hazardous materials regulations such as the ICAO Technical Instructions, IMDG Code, and carrier rules such as the IATA Dangerous Goods Regulations.  
1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2325-14(2020)(Classification)
Standard Classification for Multi-Layer Steel (MLS) and Other Metal Layer Gaskets for Transportation Applications

SIGNIFICANCE AND USE
4.1 This classification is intended to encourage uniformity in reporting properties of MLS and Metal Layer gaskets, to provide a common language for communications between producers and users, and to guide engineers and designers in the application and construction of commercially available gaskets. (A) This classification may also be used to classify Single Layer Steel (SLS) Gaskets.(B) Refer to Specification A666 or Specification A109/A109M for Stainless Steel and Low Carbon Steel, respectively. Other metals not referenced in the table or not covered by Specification A666 or Specification A109/A109M must be defined by the producer/user (that is, H – High Temperature Alloy).(C) Refer to Practice D1418 for general information regarding rubber coating types and use Classification D2000 to define the physical properties of the rubber. This physical property information is typically specified on the gasket drawing or the customer specification, or both.(D) Coated side as specified on part drawing.  
4.2 Suffix Table 2 is provided to allow hardness designation for Active, Inactive, or Load Stoppers.  
4.2.1 If suffixes are not to be used, only the basic callout from Table 1 is required. If a suffix is used for 1 layer, it must be specified for all layers, even if a “0” is used. It cannot be assumed that hardnesses of like layers are the same; if used, all layers must be specified separately. The first layer specified must be indicated on the part drawing. To use a hardness call-out, at the end of the base callout leave a space followed by the “HR” suffix with a series of suffix numbers to specify the hardnesses for each layer.
4.2.1.1 Example: ASTM F2325, A32ANBW11 HR252—Example from Table 1 modified to add hardness requirement for the three metal layers. Active layers 1 and 3 are designated to be the same, 1/4 hard steel. Stopper layer 2 is designated to be full hard steel.
SCOPE
1.1 This classification covers a means for specifying Multi-Layer Steel (MLS) and other Metal Layer Gaskets for Transportation Applications by application and construction. These structures are composed of one or more steel or metal layers of material, which may have coatings or embossments. Commercial materials designated as composite or enveloped gaskets are excluded from this classification and are covered by Classification F868 and Practice F336, respectively.  
1.2 Since all of the properties that contribute to gasket performance are not included, use of this classification as a basis for selecting an MLS or Metal Layer gasket is limited.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6055-96(2019)(Test Method)
Standard Test Methods for Mechanical Handling of Unitized Loads and Large Shipping Cases and Crates

SIGNIFICANCE AND USE
4.1 These test methods are designed for use in most cases with the actual equipment to be used in load handling.  
4.2 These test methods may be used in evaluating the shipping unit as to suitability for mechanical handling by standard user-specified load-handling equipment.  
4.3 These test methods will allow the user to determine integrity and stability of the load as well as provide guidance to improve the design of the unit load where deficiencies are found.  
4.4 Damage to products or packages observed during testing may be expected to correlate at least in a qualitative way to damage observed in actual distribution handling systems.
SCOPE
1.1 These test methods are suitable for testing the integrity of unitized loads and large cases and crates, but not individual drums or palletized drums, as well as the ability of the contents to endure normal handling, using standard mechanical handling equipment. Not all of the test methods are applicable to all products containers and loads. These test methods are applicable to common means of material handling, including pull pack, clamp truck, and spade lift-type handling equipment as follows:  
1.1.1 Test Method A—Fork Truck Handling—For testing the ability of the shipping unit to withstand repeated handlings by this test method.  
1.1.2 Test Method B—Spade Lift Test—For lifting by spade lift attachment to determine the ability of the handling flap of the case or shipping unit to withstand repeated lifting and handling by this test method.  
1.1.3 Test Method C—Clamp Handling Test—For lifting by hydraulic clamp attachment, to determine the ability of the shipping unit to withstand squeeze clamp handling consisting of repeated side compression and lifting.  
1.1.4 Test Method D—Push-Pull Handling Test—For testing the ability of a unitized load on a slip-sheet to withstand repeated handling by this test method.  
1.1.5 Test Method E—Grabhook Test—For lifting by grabhooks to determine the ability of the shipping unit to withstand the horizontal pressures of grabhooks.  
1.1.6 Test Method F—Sling Tests—For lifting by wire rope, cable, or woven fiber slings to determine the ability of the shipping unit to withstand the compression of slings.  
1.2 Additional Test Methods:  
1.2.1 Additional test methods that apply to mechanical handling and rough handling tests of unitized loads and large cases and crates include incline impact tests, described in Test Method D880; horizontal impact tests, described in Test Method D4003.  
1.2.2 Practice D4169 provides a series of options for selecting and running performance tests on all types of shipping containers and systems.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2463-19(Specification)
Standard Performance Specification for Cargo Bed Cover (CBC) M105A2 Trailer, Type II

SCOPE
1.1 This specification covers the general performance requirements for the Type II Cargo Bed Cover (CBC). The Type II Cargo Bed Cover is a removable general purpose rigid wall enclosure that is mounted on the M105A2 Trailer, Cargo: 1.5 Ton, 2 Wheel. The Type II CBC provides environmental protection and security for mission equipment and items of general transport.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parenthesis are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off