iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4035-22

(Specification)

Standard Performance Specification for Knitted Necktie and Scarf Fabrics

Standard Performance Specification for Knitted Necktie and Scarf Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4035 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers knitted necktie and scarf fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Oct-2022
ICS
61.040 - Headgear. Clothing accessories. Fastening of clothing
Technical Committee
D13 - Textiles
Drafting Committee
D13.61 - Apparel
Current Stage
Ref Project

Relations

Refers
ASTM D3787-16(2020) - Standard Test Method for Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test
Effective Date
01-Jul-2020

Buy Standard

ASTM D4035-22 - Standard Performance Specification for Knitted Necktie and Scarf FabricsASTM D4035-22 - Standard Performance Specification for Knitted Necktie and Scarf Fabrics
PreviousNext
Technical specification
ASTM D4035-22 - Standard Performance Specification for Knitted Necktie and Scarf Fabrics
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D4035-22 - Standard Performance Specification for Knitted Necktie and Scarf FabricsREDLINE ASTM D4035-22 - Standard Performance Specification for Knitted Necktie and Scarf Fabrics
PreviousNext
Technical specification
REDLINE ASTM D4035-22 - Standard Performance Specification for Knitted Necktie and Scarf Fabrics
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D4035 −22
Standard Performance Specification for
1
Knitted Necktie and Scarf Fabrics
This standard is issued under the fixed designation D4035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D3787 Test Method for Bursting Strength of Textiles—
Constant-Rate-of-Traverse (CRT) Ball Burst Test
1.1 This performance specification covers knitted necktie
3
D7022 Terminology Relating to Apparel
and scarf fabrics composed of any textile fiber or mixture of
4
2.2 AATCC Methods:
textile fibers.
TM8 Colorfastness to Crocking: Crockmeter Method
1.2 These requirements apply to the length and width
TM15 Colorfastness to Perspiration
directions for those properties where fabric direction is perti-
TM16.3 Colorfastness to Light
nent.
TM23 Colorfastness to Burnt Gas Fumes
1.3 The following precautionary statement pertains only to
TM61 Colorfastness to Laundering: Accelerated
the test methods portion, Section 7, of this specification. This
TM96 Dimensional Changes in Commercial Laundering of
standarddoesnotpurporttoaddressallofthesafetyconcerns,
Woven and Knitted Fabrics Except Wool
ifany,associatedwithitsuse.Itistheresponsibilityoftheuser
TM116 Colorfastness to Crocking: Rotary Vertical Crock-
of this standard to establish appropriate safety, health, and
meter Method
environmental practices and determine the applicability of
TM124 Smoothness Appearance of Fabrics After Repeated
regulatory limitations prior to use.
Home Laundering
1.4 This international standard was developed in accor-
TM132 Colorfastness to Drycleaning
dance with internationally recognized principles on standard-
TM135 Dimensional Changes of Fabrics
ization established in the Decision on Principles for the
TM172 Colorfastness to Powdered Non-Chlorine Bleach in
Development of International Standards, Guides and Recom-
Home Laundering
mendations issued by the World Trade Organization Technical
TM188 Colorfastness to Sodium Hypochlorite Bleach in
Barriers to Trade (TBT) Committee.
Home Laundering
EP1 Gray Scale for Color Change
2. Referenced Documents
EP2 Gray Scale for Staining
2
2.1 ASTM Standards: EP8 AATCC 9-Step Chromatic Transference Scale
5
D123 Terminology Relating to Textiles
2.3 Federal Standard:
D2594 Test Method for Stretch Properties of Knitted Fabrics
16 CFR 1610—Standard for Flammability of Clothing Tex-
Having Low Power
tiles
D2724 Test Method for Bond Strength of Bonded, Fused,
NOTE 1—Reference to test methods in this specification give only the
and Laminated Apparel Fabrics
permanent part of the designation of ASTM, AATCC, or other test
D2905 Practice for Statements on Number of Specimens for
methods. The current editions of each test method cited shall prevail.
3
Textiles (Withdrawn 2008)
3. Terminology
D3786 Test Method for Bursting Strength of Textile
Fabrics—Diaphragm Bursting Strength Tester Method
3.1 For all terminology related to D13.61, Apparel, see
Terminology D7022.
3.1.1 The following terms are relevant to this standard:
1
This performance specification is under the jurisdiction of ASTM Committee
necktie, scarf, in apparel.
D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on
Apparel.
3.2 For definitions of all other textile terms, see Terminol-
Current edition approved Nov. 1, 2022. Published December 2022. Originally
ogy D123.
approved in 1981. Last previous edition approved in 2014 as D4035 – 14. DOI:
10.1520/D4035-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Association of Textile Chemists and Colorists
Standards volume information, refer to the standard’s Document Summary page on (AATCC), P.O. Box 12215, Research Triangle Park, NC 27709, http://
the ASTM website. www.aatcc.org.
3 5
The last approved version of this historical standard is referenced on Available from Superintendent of Documents, Government Printing Office,
www.astm.org. Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4035−22
3.3 For terms relating to chemical or colorfastness testing, demands dictate varying performance parameters for any
refer to specific AATCC methods. particular style of fabric.
5.4 Thesignificanceanduseofparticularpropertiesandtest
4. Specification Requirements
meth
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D4035 − 14 D4035 − 22
Standard Performance Specification for
1
Knitted Necktie and Scarf Fabrics
This standard is issued under the fixed designation D4035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This performance specification covers knitted necktie and scarf fabrics composed of any textile fiber or mixture of textile
fibers.
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.
1.3 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification.This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability
of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D123 Terminology Relating to Textiles
D2594 Test Method for Stretch Properties of Knitted Fabrics Having Low Power
D2724 Test Method for Bond Strength of Bonded, Fused, and Laminated Apparel Fabrics
3
D2905 Practice for Statements on Number of Specimens for Textiles (Withdrawn 2008)
D3786 Test Method for Bursting Strength of Textile Fabrics—Diaphragm Bursting Strength Tester Method
D3787 Test Method for Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test
3
D7022 Terminology Relating to Apparel
4
2.2 AATCC Methods:
8TM8 Colorfastness to Crocking: Crockmeter Method
15TM15 Colorfastness to Perspiration
16.3TM16.3 Colorfastness to Light
23TM23 Colorfastness to Burnt Gas Fumes
61TM61 Colorfastness to Laundering: Accelerated
96TM96 Dimensional Changes in Commercial Laundering of Woven and Knitted Fabrics Except Wool
116TM116 Colorfastness to Crocking: Rotary Vertical Crockmeter Method
1
This performance specification is under the jurisdiction of ASTM Committee D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on Apparel.
Current edition approved Feb. 1, 2014Nov. 1, 2022. Published March 2014December 2022. Originally approved in 1981. Last previous edition approved in 20132014 as
D4035 – 13.D4035 – 14. DOI: 10.1520/D4035-14.10.1520/D4035-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Research Triangle Park, NC 27709, http://www.aatcc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4035 − 22
124TM124 Smoothness Appearance of Fabrics After Repeated Home Laundering
132TM132 Colorfastness to Drycleaning
135TM135 Dimensional Changes of Fabrics
172TM172 Colorfastness to Powdered Non-Chlorine Bleach in Home Laundering
188TM188 Colorfastness to Sodium Hypochlorite Bleach in Home Laundering
Evaluation Procedure 1EP1 Gray Scale for Color Change
Evaluation Procedure 2EP2 Gray Scale for Staining
Evaluation Procedure 8EP8 AATCC 9-Step Chromatic Transference Scale
5
2.3 Federal Standard:
16 CFR 1610—Standard for Flammability of Clothing Textiles
NOTE 1—Reference to test methods in this specification give only the permanent part of the designation of ASTM, AATCC, or other test methods. The
current editions of each test method cited shall prevail.
3. Terminology
3.1 For all terminology related to D13.61, Apparel, see Terminology D7022.
3.1.1 The following terms are relevant to this standard: necktie, scarf, in apparel.
3.2 For definitions of all other textile terms, see Terminology D123.
3.3 For terms relating to chemical or colorfastness t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2050-23(Terminology)
Standard Terminology Relating to Fastener Subassemblies Used in the Manufacture of Textiles

SCOPE
1.1 This standard identifies terminology related to subassemblies which are categorized as any component that is used in the construction or assembly of a textile product. Subassemblies can be in the form of components used as closures (for example, slide fasteners, buttons, snap fasteners, hook and loop (touch) fasteners) or methods used to join textile sections (for example, stitches and seams).  
1.2 Terms relating to Buttons are found in Section 3.  
1.3 Terms relating to Hook and Loop (Touch) fasteners are in Section 4.  
1.4 Terms relating to Snap Fasteners are found in Section 5.  
1.5 Terms relating to Slide Fasteners are found in Section 6.  
1.6 For other terms related to textiles, refer to Terminology D123.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D4153-22(Specification)
Standard Performance Specification for Men's, Women's, and Children's Woven Handkerchief Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4153 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics to be used in the manufacture of men's, women's, and children's handkerchiefs, both utilitarian and decorative.  
1.2 This performance specification is not applicable to open-work fabrics such as lace which is used primarily to decorate handkerchiefs, or woven fabrics used for the manufacture of scarves.  
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2059/D2059M-03(2022)(Test Method)
Standard Test Method for Resistance of Zippers to Salt Spray (Fog)

SIGNIFICANCE AND USE
5.1 The resistance of a zipper to a variety of saline and non-saline environments can be estimated from the amount and nature of corrosion products and their effect on operability. Results of exposure to the salt spray are merely indicative of the reaction to other corrosive conditions. While the results cannot be related precisely to a given length of exposure in a specific atmosphere, they are useful for measuring relative performance under prescribed conditions for controlling a manufacturing process, and for measuring the effectiveness of protective coatings.  
5.2 Test Method D2059 for the determination of the resistance of zippers to salt spray is considered satisfactory for acceptance testing of commercial shipments of zippers because the test method is used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2058, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. T...
SCOPE
1.1 This test method covers the determination of the resistance of all types of zippers to corrosion and their ability to function properly after exposure of specified duration in a prescribed salt spray.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2054-99(2022)(Test Method)
Standard Test Method for Colorfastness of Zipper Tapes to Crocking

SIGNIFICANCE AND USE
5.1 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the determination of the degree of color that may be transferred from the textile tape of zippers of all fibers to other surfaces by rubbing under wet or dry conditions, or both.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2051-14(2022)(Test Method)
Standard Test Method for Durability of Finish of Zippers to Laundering

SIGNIFICANCE AND USE
5.1 Test Method D2051 is useful for testing to determine the effect of repeated laundering on the appearance of the decorative coating of a zipper.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The test method(s) in the standard along with those in Test Methods D2052, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an inti...
SCOPE
1.1 This test method covers the determination of the durability of the enamel or other decorative coating of a zipper when subjected to laundering.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2053-99(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Light

SIGNIFICANCE AND USE
5.1 This test method is useful in determining if the loss of color due to light exposure is satisfactory for the intended end-use.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The test method(s) in this standard along with those in Test Methods D2051, D2052, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and...
SCOPE
1.1 This test method covers the determination of the alteration in shade of the textile portion of zippers when exposed to light, regardless of the materials of manufacture.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2058-03(2022)(Test Method)
Standard Test Method for Durability of Finish of Zippers to Drycleaning

SIGNIFICANCE AND USE
5.1 Test Method D2058 is useful for determining the effect of repeated drycleaning on the appearance of the decorative coating of a zipper.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2059, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thoroug...
SCOPE
1.1 This test method covers the determination of the durability of the enamel or other decorative coating of zippers when subjected to drycleaning.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2060-14(2022)(Test Method)
Standard Test Methods for Measuring Zipper Dimensions

SIGNIFICANCE AND USE
4.1 The significance of specific tests is discussed in the appropriate sections.  
4.2 These test methods are considered satisfactory for acceptance testing of commercial shipments because the test methods have been used extensively in the trade for this purpose, and because current estimates of between-laboratory precision are acceptable in most cases.  
4.2.1 In case of a dispute arising from differences in reported test results when using Test Methods D2060 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias if found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.  
4.3 The test method(s) in these test methods, along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2058, D2059, D2061, and D2062, are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either be...
SCOPE
1.1 These test methods cover the measurement of the dimensions of all types and sizes of zippers.  
1.2 The test methods appear as follows:    
Sections  
Chain Flatness  
34 – 39  
Chain Straightness  
40 – 44  
Chain Thickness  
28 – 33  
Chain Width  
45 – 50  
Length of Zipper or Parts  
9 – 14  
Longitudinal Dimensional Change  
51 – 58  
Slider Mouth Width  
21 – 27  
Tape Width  
15 – 20  
1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D2057-05(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Laundering

SIGNIFICANCE AND USE
5.1 Test Method D2057 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur.
Note 1: For guidance in evaluating the results of this method, refer to Practice D3692.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in this standard along with those in D2051, D2052, D2053, D2054, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because...
SCOPE
1.1 This test method covers the determination of alteration in shade and of staining under conditions similar to that experienced in domestic washing of zipper stringers. This test method is applicable to the textile portion of zipper stringers that utilize tapes made of cotton, linen, or manufactured organic fibers, and to combinations thereof.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2052-05(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Drycleaning

SIGNIFICANCE AND USE
5.1 Test Method D2052 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur.
Note 1: For guidance in evaluating the results of this test method, refer to Practice D3692.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in this standard along with those in Test Methods D2051, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been publishe...
SCOPE
1.1 This test method covers the determination of change in shade and of staining of zipper stringers under drycleaning conditions. This test method is applicable to the textile portion of zipper stringers of all materials.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off