ASTM F1842-15
(Test Method)Standard Test Method for Determining Ink or Coating Adhesion on Flexible Substrates for a Membrane Switch or Printed Electronic Device (Withdrawn 2024)
Standard Test Method for Determining Ink or Coating Adhesion on Flexible Substrates for a Membrane Switch or Printed Electronic Device (Withdrawn 2024)
SIGNIFICANCE AND USE
5.1 If the ink or coating is to fulfill its function, it must adhere to the substrate. Substrates and their surface preparation have a significant effect on the adhesion of inks or coatings. Therefore, a method of evaluating adhesion of inks or coatings to different substrates or surface treatments, or of different inks or coatings to the same substrate and surface treatment, is useful to the industry.
5.2 The limitations of all adhesion methods and the specific limitation of this test method to lower levels of adhesion should be recognized before using it. The intra– and inter–laboratory precision of this test method is under evaluation.
5.3 Printing area to be tested should be a solid area large enough to include the entire cross hatch pattern.
SCOPE
1.1 This test method is based on existing Test Method D3359, with modifications to make it suitable for flexible substrates, printed electronic devices and membrane switches.
1.2 Despite the problems associated with a tape test on plastic substrates, it is our belief that this is still one of the best ways to test ink and coating for adhesion for membrane switch or printed electronic device applications. In writing this test method we are addressing several of the objections to the test method that could affect its precision and repeatability on plastic substrates.
1.3 These test methods cover whether the adhesion of coating or ink to a substrate is at an acceptable level. They do not distinguish between higher levels of adhesion, for which more sophisticated methods of measurement may be required.
Note 1: It should be recognized that differences in adherability of the ink or coating surface can affect the results obtained with inks or coatings having the same inherent adhesion.
1.4 In multi–coat systems adhesion failure may occur between coats, so that the adhesion of the coating system to the substrate is not determined.
1.5 This test method is specifically designed for measuring adhesion of inks and coatings (films) that have a thickness of 5 mil (125 microns) or less, on plastics such as polyester and polycarbonate.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This test method is based on existing Test Method D3359, with modifications to make it suitable for flexible substrates, printed electronic devices and membrane switches.
Formerly under the jurisdiction of Committee F01 on Electronics, this test method was withdrawn in January 2024 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1842 − 15
Standard Test Method for
Determining Ink or Coating Adhesion on Flexible Substrates
1
for a Membrane Switch or Printed Electronic Device
This standard is issued under the fixed designation F1842; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
1.1 This test method is based on existing Test Method
D3359, with modifications to make it suitable for flexible
2. Referenced Documents
substrates, printed electronic devices and membrane switches. 2
2.1 ASTM Standards:
1.2 Despite the problems associated with a tape test on D3359 Test Methods for Measuring Adhesion by Tape Test
plastic substrates, it is our belief that this is still one of the best
3. Terminology
ways to test ink and coating for adhesion for membrane switch
3.1 membrane switch—a momentary switching device in
or printed electronic device applications. In writing this test
which at least one contact is on, or made of, a flexible
method we are addressing several of the objections to the test
substrate.
method that could affect its precision and repeatability on
plastic substrates.
4. Summary of Test Method
1.3 These test methods cover whether the adhesion of
4.1 A lattice pattern with six cuts in each direction is made
coating or ink to a substrate is at an acceptable level. They do
in the ink or coating to the substrate. Pressure sensitive tape is
not distinguish between higher levels of adhesion, for which
applied over the lattice and then removed, and adhesion is
more sophisticated methods of measurement may be required.
evaluated by comparison with the descriptions and illustra-
tions.
NOTE 1—It should be recognized that differences in adherability of the
ink or coating surface can affect the results obtained with inks or coatings
5. Significance and Use
having the same inherent adhesion.
5.1 If the ink or coating is to fulfill its function, it must
1.4 In multi–coat systems adhesion failure may occur be-
adhere to the substrate. Substrates and their surface preparation
tween coats, so that the adhesion of the coating system to the
have a significant effect on the adhesion of inks or coatings.
substrate is not determined.
Therefore, a method of evaluating adhesion of inks or coatings
1.5 This test method is specifically designed for measuring to different substrates or surface treatments, or of different inks
or coatings to the same substrate and surface treatment, is
adhesion of inks and coatings (films) that have a thickness of
5 mil (125 microns) or less, on plastics such as polyester and useful to the industry.
polycarbonate.
5.2 The limitations of all adhesion methods and the specific
limitationofthistestmethodtolowerlevelsofadhesionshould
1.6 This standard does not purport to address all of the
be recognized before using it. The intra– and inter–laboratory
safety concerns, if any, associated with its use. It is the
precision of this test method is under evaluation.
responsibility of the user of this standard to establish appro-
5.3 Printing area to be tested should be a solid area large
enough to include the entire cross hatch pattern.
1
This practice is under the jurisdiction ofASTM Committee F01 on Electronics
2
and is the direct responsibility of Subcommittee F01.18 on Printed Electronics. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
CurrenteditionapprovedJune1,2015.PublishedJuly2015.Originallyapproved contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
in 1997. Last previous edition approved in 2009 as F1842-09. DOI: 10.1520/F1842- Standards volume information, refer to the standard’s Document Summary page on
15. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1842 − 15
6. Interferences 9.6 Place the center of the tape over the grid with the tape
The type of tape used should be compatible with the type of oriented in the direction of one of the cuts and smooth into
inks used. place by a finger. To ensure good contact with the ink or
coating, press tape firmly to thoroughly wet the adhesive to the
7. Apparatus
surface of the ink or coating. The color under the tape is a
7.1 Cutting Tool— A multi–blade cutter having a cutting useful indication of when good
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1842 − 09 F1842 − 15
Standard Test Method for
Determining Ink or Coating Adhesion on PlasticFlexible
Substrates for a Membrane Switch Applicationsor Printed
1
Electronic Device
This standard is issued under the fixed designation F1842; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method is based on existing Test Method D3359, with modifications to make it suitable for plastic substrates
flexible substrates, printed electronic devices and membrane switches.
1.2 Despite the problems associated with a tape test on plastic substrates, it is our belief that this is still one of the best ways
to test ink and coating for adhesion for membrane switch or printed electronic device applications. In writing this test method we
are addressing several of the objections to the test method that could affect its precision and repeatability on plastic substrates.
1.3 These test methods cover whether the adhesion of coating or ink to a substrate is at an acceptable level. They do not
distinguish between higher levels of adhesion, for which more sophisticated methods of measurement may be required.
NOTE 1—It should be recognized that differences in adherability of the ink or coating surface can affect the results obtained with inks or coatings having
the same inherent adhesion.
1.4 In multi–coat systems adhesion failure may occur between coats, so that the adhesion of the coating system to the substrate
is not determined.
1.5 This test method is specifically designed for measuring adhesion of inks and coatings (films) that have a thickness of 5 mil
(125 microns) or less, on plastics such as polyester and polycarbonate.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D3359 Test Methods for Measuring Adhesion by Tape Test
3. Terminology
3.1 membrane switch—a momentary switching device in which at least one contact is on, or made of, a flexible substrate.
4. Summary of Test Method
4.1 A lattice pattern with six cuts in each direction is made in the ink or coating to the substrate. Pressure sensitive tape is
applied over the lattice and then removed, and adhesion is evaluated by comparison with the descriptions and illustrations.
5. Significance and Use
5.1 If the ink or coating is to fulfill its function, it must adhere to the substrate. Substrates and their surface preparation have
a significant effect on the adhesion of inks or coatings. Therefore, a method of evaluating adhesion of inks or coatings to different
substrates or surface treatments, or of different inks or coatings to the same substrate and surface treatment, is useful to the industry.
1
This practice is under the jurisdiction of ASTM Committee F01 on Electronics and is the direct responsibility of Subcommittee F01.18 on Membrane SwitchesPrinted
Electronics.
Current edition approved June 15, 2009June 1, 2015. Published July 2009July 2015. Originally approved in 1997. Last previous edition approved in 20022009 as
F1842-02.-09. DOI: 10.1520/F1842-09.10.1520/F1842-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1842 − 15
5.2 The limitations of all adhesion methods and the specific limitation of this test method to lower levels of adhesion should
be recognized before using it. The intra– and inter–laboratory precision of this test method is under evaluation.
5.3 Printing area to be tested should be a solid area large enough to include the entire cross hatch pattern.
6. Interferences
The type of tape used should be compatible with the type of inks used.
7. Apparatus
7.1 Cutting Tool— A multi–blade cutter having a cutting edge angle between 15 and 30 degrees that will make six cuts at once
that are 2 mm apar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.