ASTM D7319-22
(Test Method)Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
SIGNIFICANCE AND USE
5.1 Sulfates and chlorides can be found in filter plugging deposits and fuel injector deposits. The acceptability for use of the fuel components and the finished fuels depends on the sulfate and chloride content.
5.2 Existent and potential inorganic sulfate and total chloride content, as measured by this test method, can be used as one measure of the acceptability of gasoline components for automotive spark-ignition engine fuel use.
SCOPE
1.1 This test method covers a direct injection ion chromatographic procedure for determining existent and potential inorganic sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol and butanol to be used in motor fuel applications. It is intended for the analysis of ethanol and butanol samples containing between 1.0 mg/kg to 20 mg/kg of existent or potential inorganic sulfate and 1.0 mg/kg to 50 mg/kg of inorganic chloride.
Note 1: Tertiary butanol is not included in this test method. 1-butanol, 2-butanol, and isobutanol are included in the testing and research report for this test method.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D7319 − 22
Standard Test Method for
Determination of Existent and Potential Sulfate and
Inorganic Chloride in Fuel Ethanol and Butanol by Direct
1
Injection Suppressed Ion Chromatography
This standard is issued under the fixed designation D7319; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D4052 Test Method for Density, Relative Density, and API
Gravity of Liquids by Digital Density Meter
1.1 This test method covers a direct injection ion chromato-
D4057 Practice for Manual Sampling of Petroleum and
graphic procedure for determining existent and potential inor-
Petroleum Products
ganic sulfate and total inorganic chloride content in hydrous
D4175 Terminology Relating to Petroleum Products, Liquid
and anhydrous denatured ethanol and butanol to be used in
Fuels, and Lubricants
motor fuel applications. It is intended for the analysis of
D4177 Practice for Automatic Sampling of Petroleum and
ethanol and butanol samples containing between 1.0 mg⁄kg to
Petroleum Products
20 mg/kg of existent or potential inorganic sulfate and
D5827 Test Method for Analysis of Engine Coolant for
1.0 mg⁄kg to 50 mg/kg of inorganic chloride.
Chloride and Other Anions by Ion Chromatography
NOTE 1—Tertiary butanol is not included in this test method. 1-butanol,
D6299 Practice for Applying Statistical Quality Assurance
2-butanol, and isobutanol are included in the testing and research report
and Control Charting Techniques to Evaluate Analytical
for this test method.
Measurement System Performance
1.2 The values stated in SI units are to be regarded as
D6792 Practice for Quality Management Systems in Petro-
standard. No other units of measurement are included in this
leum Products, Liquid Fuels, and Lubricants Testing
standard.
Laboratories
1.3 This standard does not purport to address all of the
D7318 TestMethodforExistentInorganicSulfateinEthanol
safety concerns, if any, associated with its use. It is the
by Potentiometric Titration
responsibility of the user of this standard to establish appro-
D7328 Test Method for Determination of Existent and Po-
priate safety, health, and environmental practices and deter-
tential Inorganic Sulfate and Total Inorganic Chloride in
mine the applicability of regulatory limitations prior to use.
Fuel Ethanol by Ion Chromatography Using Aqueous
Material Safety Data Sheets are available for reagents and
Sample Injection
materials. Review them for hazards prior to usage.
3
2.2 European Norm Standards:
1.4 This international standard was developed in accor-
EN 15492 Ethanol as a blending component for petrol—
dance with internationally recognized principles on standard-
Determination of inorganic chloride and sulfate content—
ization established in the Decision on Principles for the
Ion chromatographic method
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
3. Terminology
Barriers to Trade (TBT) Committee.
3.1 Definitions:
2. Referenced Documents
3.1.1 For definitions of terms used in this test method, refer
2
2.1 ASTM Standards: to Terminology D4175.
D1193 Specification for Reagent Water 3.2 Definitions of Terms Specific to This Standard:
3.2.1 existent inorganic sulfate, n—inorganic sulfate species
1
This test method is under the jurisdiction of ASTM Committee D02 on actually present in the sample at the time of analysis with no
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
oxidation treatment.
Subcommittee D02.03 on Elemental Analysis.
3.2.2 inorganic chloride, n—chloride present as hydrochlo-
Current edition approved Oct. 1, 2022. Published October 2022. Originally
approved in 2007. Last previous edition approved in 2017 as D7319 – 17. DOI:
ric acid, ionic salts of this acid, or mixtures of these.
10.1520/D7319-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ------------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7319 − 17 D7319 − 22
Standard Test Method for
Determination of Existent and Potential Sulfate and
Inorganic Chloride in Fuel Ethanol and Butanol by Direct
1
Injection Suppressed Ion Chromatography
This standard is issued under the fixed designation D7319; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers a direct injection ion chromatographic procedure for determining existent and potential inorganic
sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol and butanol to be used in motor fuel
applications. It is intended for the analysis of ethanol and butanol samples containing between 1.0 mg ⁄kg to 20 mg/kg of existent
or potential inorganic sulfate and 1.0 mg ⁄kg to 50 mg/kg of inorganic chloride.
NOTE 1—Tertiary butanol is not included in this test method. 1-butanol, 2-butanol, and isobutanol are included in the testing and research report for this
test method.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards
prior to usage.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1193 Specification for Reagent Water
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4175 Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D5827 Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography
D6299 Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measure-
ment System Performance
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.03 on Elemental Analysis.
Current edition approved Oct. 1, 2017Oct. 1, 2022. Published October 2017October 2022. Originally approved in 2007. Last previous edition approved in 20132017 as
D7319 – 13.D7319 – 17. DOI: 10.1520/D7319-17.10.1520/D7319-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7319 − 22
D6792 Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
D7318 Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration
D7328 Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol
by Ion Chromatography Using Aqueous Sample Injection
3
2.2 European Norm Standards:
EN 15492 Ethanol as a blending component for petrol—Determination of inorganic chloride and sulfate content—Ion
chromatographic method
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms used in this test method, refer to Terminology D4175.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 existent inorganic sulfate, n—inorganic sulfate species actually present in the sample at the time of analysis with no oxidation
treatment.
3.2.2 inorganic chloride, n—chloride present
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.