iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6536-00(2005)

(Test Method)

Standard Test Method for Measuring the Dip Tube Length of a Mechanical Pump Dispenser

Standard Test Method for Measuring the Dip Tube Length of a Mechanical Pump Dispenser

SIGNIFICANCE AND USE
This test method is to be used to measure the length of a specified dip tube from the bottom of the sealing surface to the end of the dip tube in a mechanical pump dispenser.
This test method is to be used to measure the exposed length of a specified dip tube of a mechanical pump dispenser.
SCOPE
1.1 This test method covers the measurement technique for a dip tube of a mechanical pump dispenser.
1.2 The values stated in both inch-pound and SI units are to be regarded separately as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Sep-2005
ICS
55.130 - Aerosol containers
Technical Committee
D10 - Packaging
Drafting Committee
D10.33 - Aerosol Products
Current Stage
Ref Project

Relations

Replaces
ASTM D6536-00 - Standard Test Method for Measuring the Dip Tube Length of a Mechanical Pump Dispenser
Effective Date
01-Oct-2005
Replaced By
ASTM D6536/D6536M-00(2010)e1 - Standard Test Method for Measuring the Dip Tube Length of a Mechanical Pump Dispenser
Effective Date
01-Oct-2010

Buy Standard

ASTM D6536-00(2005) - Standard Test Method for Measuring the Dip Tube Length of a Mechanical Pump DispenserASTM D6536-00(2005) - Standard Test Method for Measuring the Dip Tube Length of a Mechanical Pump Dispenser
PreviousNext
Standard
ASTM D6536-00(2005) - Standard Test Method for Measuring the Dip Tube Length of a Mechanical Pump Dispenser
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6536–00 (Reapproved 2005)
Standard Test Method for
Measuring the Dip Tube Length of a Mechanical Pump
Dispenser
This standard is issued under the fixed designation D6536; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the measurement technique for
a dip tube of a mechanical pump dispenser.
1.2 The values stated in both inch-pound and SI units are to
be regarded separately as the standard.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
2. Significance and Use
FIG. 1 Overall Dip Tube Length “X” Versus Exposed Dip Tube
2.1 This test method is to be used to measure the length of
Length “Z”
a specified dip tube from the bottom of the sealing surface to
the end of the dip tube in a mechanical pump dispenser.
TEST METHOD “B”—MEASUREMENT OF EXPOSED
2.2 This test method is to be used to measure the exposed
DIP TUBE LENGTH
length of a specified dip tube of a mechanical pump dispenser.
NOTE 2—This test method is used in all applications.
3. Apparatus
4.5 While holding the mechanical pump dispenser with its
3.1 Thin Metal Ruler, with minimum gradients of 1 mm or
axis in a horizontal plane, place the zero index end of the ruler
⁄16 in., or both, along with a zero index at the end of the ruler.
against the bottom end of the body. Fig. 1—dimension “Z”.
3.2 Calipers.
4.6 If needed straighten the dip tube out so that it is parallel
with the length of the ruler.
4. Procedure
4.7 Measure the exposed length of the dip tube to within a
TEST METHOD “A”—MEASUREMENT OF
full millimetre or ⁄16 in. length.
OVERALL DIP TUBE LENGTH
4.8 Record the length measured in 5.1.
NOTE 1—This test method is used when the exposed sealing surface of
5. Report
the mechanical pump dispenser is large enough to measure from.
5.1 Report the following information:
4.1 While holding the mechanical pump dispenser with its
5.1.1 Type of mechanical pump dispenser,
axis in a horizontal plane, place the zero index end of the ruler
5.1.2 Dip tube length measured, and
against the bottom of the seal surface. Fig. 1—dimension “X”.
5.1.3 Method used.
4.2
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2872-14(2024)(Guide)
Standard Guide for Determining Cross-Section Averaged Characteristics of a Spray Using Laser-Diffraction Instruments in a Wind Tunnel Apparatus

SIGNIFICANCE AND USE
5.1 This guide provides a means of using an LD instrument to obtain a droplet size distribution from a spray in gas co-flow that approximates a flux-sensitive sample.4  
5.2 In many sprays, the experimenter shall account for spatial segregation of droplets by size. This guide provides a means of spatial averaging the droplet distribution.  
5.3 The results obtained will be statistical in nature and refer to the time average of droplet size distribution of the entire spray.  
5.4 This guide is used to calibrate a spray generation device to produce a desired droplet size distribution under prespecified environmental and co-flow conditions or characterize an unknown spray while minimizing the uncertainty in the measurement.
SCOPE
1.1 The purpose of this guide is to define a test procedure for applying the laser diffraction (LD) method to estimate an average droplet size distribution that characterizes the flux of liquid droplets produced by a specified spray generation device under specified gas co-flow conditions using a specified liquid. The intended scope is limited to artificially generated sprays with high speed co-flow. The droplets are assumed to be in the size range of 1 µm to 2000 µm in diameter and occur in sprays that are contained within a volume as small as a few cubic centimetres or as large as a cubic metre. The droplet sizes are assumed to be distributed non-uniformly within the spray volume.  
1.2 This guide is intended primarily to guide measurement of performance of nozzles and atomizers using LD instruments.  
1.3 Non-uniform sprays require measurements across the entire spray cross section or through several chords providing a representative sample of the overall spray cross section. The aim of multiple-chord measurements is to obtain a single droplet size distribution that characterizes the whole spray rather than values from a single chordal measurement.  
1.4 Use of this guide requires that the instrument does not interfere with spray production and does not significantly impinge upon or disturb the co-flow of gas and the spray. This technique is, therefore, considered non-intrusive.  
1.5 The computation of droplet size distributions from the light-scattering distributions is done using Mie scattering theory or Fraunhofer diffraction approximation. The use of Mie theory accounts for light refracted through the droplet and there is a specific requirement for knowledge of both real (refractive) and imaginary (absorptive) components of the complex index of refraction. Mie theory also relies on an assumption of droplet homogeneity. The Fraunhofer diffraction approximation does not account for light refracted through the droplet and does not require knowledge of the index of refraction.  
1.6 The instruments shall include data-processing capabilities to convert the LD scattering intensities into droplet size distribution parameters in accordance with Practice E799 and Test Method E1260.  
1.7 The spray is visible and accessible to the collimated beam produced by the transmitter optics of the LD instrument. The shape and size of the spray shall be contained within the working distance of the LD system optics as specified by the instrument manufacturer.  
1.8 The size range of the LD optic should be appropriate to the spray generation device under study. For example, the upper bound of the smallest droplet size class reported by the instrument shall be not more than 1/4 the size of DV0.1.  
1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.10 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory lim...

  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM D7952-15(2021)(Test Method)
Standard Test Method for Measuring Aspiration Potential of Aerosol Products

SIGNIFICANCE AND USE
4.1 This test method provides a means of measuring whether or not an aerosol product may present an aspiration risk if a dispensed aerosol gets into one’s mouth.  
4.2 The degree of risk for aspiration of an aerosol depends both on spray pattern as well as aerosol deposition rate.2  
4.3 This test method will be used to determine the need for child-resistant packaging of aerosol products.
SCOPE
1.1 This test method covers a small-scale laboratory procedure to determine the aspiration potential of aerosol products by determining spray pattern and aerosol deposition rates.  
1.2 This test method has been developed to address a need to identify which aerosol products may present an aspiration risk such that special labeling and/or child-resistant packaging would be appropriate. Studies based on this method may allow the development of a practice to identify such aerosol products.  
1.3 Although this method may be useful for testing non-pressurized aerosol products, its development has been limited to testing pressurized aerosols.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1260-03(2020)(Test Method)
Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments

SIGNIFICANCE AND USE
5.1 The purpose of this test method is to provide data on liquid drop-size characteristics for sprays, as indicated by optical nonimaging light-scattering instruments. The results obtained generally will be statistical in nature. The number of variables concerned in the production of liquid spray, together with the variety of optical, electronic, and sampling systems used in different instruments, may contribute to variations in the test results. Care must be exercised, therefore, when attempting to compare data from samples obtained by different means.
SCOPE
1.1 The purpose of this test method is to obtain data which characterize the sizes of liquid particles or drops such as are produced by a spray nozzle or similar device under specified conditions using a specified liquid. The drops will generally be in the size range from 5-μm to the order of 1 000-μm diameter; they will occur in sprays which may be as small as a few cubic centimetres or as large as several cubic metres. Typically the number density of the particles can vary significantly from one point to another.  
1.2 This test method is intended primarily for use in standardizing measurements of the performance of sprayproducing devices. It is limited to those techniques and instruments that operate by passing a beam of light through the spray and analyzing the light scattered by the droplets to derive size information. Such techniques do not produce images of individual drops, and therefore, are known as “optical (nonimaging) instruments.”  
1.3 The measurements made, when referred to the entire spray being sampled, may be flux sensitive or spatial, as defined in Practice E799, depending on the techniques used with a particular instrument.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4336-18(Practice)
Standard Practice for Determination of the Output Per Stroke of a Mechanical Pump Dispenser

SIGNIFICANCE AND USE
3.1 This practice can be used to compare the output per stroke of different pump dispensers for the purpose of establishing dosage and use instructions for products of consumer usage.  
3.2 This practice is suitable for establishing specifications for both the pump dispenser and the final package.
SCOPE
1.1 This practice covers the measurement of the mean quantity-by-weight of liquids dispensed from a mechanical pump dispenser (spray or flow type) with a consumer-type product on each actuation.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6534-18(Practice)
Standard Practice for Determining the Peak Force-to-Actuate of a Mechanical Pump Dispenser

ABSTRACT
This test method covers the procedures for determining the peak force-to-actuate of a mechanical pump dispenser. The apparatus required to perform the tests include a motorized compression tester or custom force-to-action machine, a device that can display the resulting force, and a means to rigidly hold the mechanical pump dispenser during testing. Appropriate machine operating and substance handling should be taken and calibration should be performed on the equipment before testing the clean, dry, and unused pump dispensers.
SCOPE
1.1 This practice covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.  
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 5.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6536/D6536M-18(Practice)
Standard Practice for Measuring the Dip Tube Length of a Mechanical Pump Dispenser

SIGNIFICANCE AND USE
2.1 This practice is to be used to measure the length of a specified dip tube from the bottom of the sealing surface to the end of the dip tube in a mechanical pump dispenser.  
2.2 This practice is to be used to measure the exposed length of a specified dip tube of a mechanical pump dispenser.
SCOPE
1.1 This practice covers the measurement technique for a dip tube of a mechanical pump dispenser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6535/D6535M-18(Practice)
Standard Practice for Determining the Dip Tube Length of a Mechanical Pump Dispenser

SIGNIFICANCE AND USE
2.1 This practice is to be used to determine the length of a dip tube of a mechanical pump dispenser that extends to the bottom-corner of a container.  
2.2 This practice is to be used to determine the length of a dip tube of a mechanical pump dispenser that extends to the bottom-center of a container.
SCOPE
1.1 This practice covers the determination technique for a dip tube of a mechanical pump dispenser.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4333/D4333M-18(Practice)
Standard Practice for Compatibility of Mechanical Pump Dispenser Components

SIGNIFICANCE AND USE
2.1 This practice identifies the compatibility of the mechanical pump dispenser components with consumer-type products.
SCOPE
1.1 This practice covers testing of the components of mechanical pump dispensers (spray or flow types) for compatibility with products.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6654-18(Practice)
Standard Practice for Basic Storage Stability of a Mechanical Pump Dispenser

SIGNIFICANCE AND USE
3.1 Determining the storage of a mechanical pump dispenser for consumer usage. Products of consumer usage are of the personal care, household, insecticides, food, automotive, and institutional nature. Pharmaceutical and cosmetic products including perfume are not covered under this practice.
SCOPE
1.1 This practice covers the determination of the basic storage stability of a mechanical pump dispenser with a product.  
1.2 This practice covers an evaluation of the weight lost during storage of mechanical pump dispensers (spray or flow types) with a product.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6633-18(Practice)
Standard Practice for Basic Functional Stability of a Mechanical Pump Dispenser

SIGNIFICANCE AND USE
3.1 This practice is used for determining the accelerated usage of a mechanical pump dispenser for consumer usage.
SCOPE
1.1 This practice covers the determination of the basic functional stability of a mechanical pump dispenser with a product.  
1.2 This practice covers accelerated usage evaluations of mechanical pump dispensers (spray or flow types) with a product.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific precautions are given in Section 5.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off