CEN/TC 165/WG 7 - Steel pipes

This European Standard applies to pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems and specifies dimensions and tolerances for pipes, fittings and pipe connectors and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements.
This part of EN 1124 is only valid in connection with EN 1124 1.

This European Standard specifies requirements, dimensions and tolerances for pipes and fittings of longitudinally welded, stainless steel pipe with spigot and socket used for vacuum drainage systems inside and outside buildings and for gravity and vacuum drainage systems on ships and floating maritime structures ) :
-   above freeboard deck as long as the heeling is taken into account in the event of damage when installed above freeboard deck on passenger ships;
-   inside a watertight compartment below freeboard deck;
-   with direct connection to the outboard (not permitted below freeboard deck);
-   inside tanks as long as these are not filled with foreign media and are not cargo tanks.
On well-anchored maritime structures, this European Standard applies to pipes and fittings of longitudinally welded stainless steel pipe with spigot and socket used in drainage systems in the accommodation area.
Pipes and fittings according to this European Standard may also be used in central vacuum cleaning installations, in vacuum suction lifting installations, in chip transporting installations and in other waste water and process pipes as long as the media to be discharged do not damage the components or the health and safety of the personnel.
For other pipes, this European Standard only applies if agreed with the relevant operators and following prior consultation with the manufacturer.
This European Standard contains a designation system for the different types of pipes and fittings for easy identification of each component.
This European Standard is only applicable in conjunction with EN 1124-1.

This European Standard is applicable to pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems.
It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals of the System X and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements.
NOTE   System X is a system of pipes and fittings of longitudinally welded stainless steel pipes with two-step sockets.
This European Standard is only valid in connection with EN 1124-1. This European Standard does not apply to the marking of products. EN 1124-1/A1 applies to the marking.

This standard applies to pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot
and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings, pipe connectors
and seals and establishes a system of designations for the different pipe and fitting types that conform to the
stated requirements. This standard is only valid in connection with EN 1123-1. This standard does not apply
to the marking of products. EN 1123-1 applies to the marking.

2005-08-24:ADC:DOW=DAV+21 months
2004-02 Mr Kropf TC released the final drafts for FV, SR accepted,  in CMC for FV
2003-11 DIN Still uneder discussion with S REIN before FV
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

2005-08-24:ADC:DOW=DAV+21 months
2004-02 Mr Kropf TC released the final drafts for FV, SR accepted,  in CMC for FV
2003-11 DIN Still uneder discussion with S REIN before FV

This document specifies requirements, dimensions and tolerances for pipes and fittings of longitudinally
welded, hot-dip galvanized steel pipe with spigot and socket used for vacuum drainage systems inside and
outside buildings and for gravity and vacuum drainage systems on ships and floating maritime structures 1) :
.above freeboard deck as long as the heeling is taken into account in the event of damage when installed
above freeboard deck on passenger ships;
.inside a watertight compartment below freeboard deck;
.with direct connection to the outboard (not permitted below freeboard deck);
.inside tanks as long as these are not filled with foreign media and are not cargo tanks.
On well-anchored maritime structures, this standard applies to pipes and fittings of longitudinally welded hot-dip
galvanized steel pipe with spigot and socket used in drainage systems in the living area.
NOTE Pipes and fittings according to this document may also be used in central vacuum cleaning installations, in
vacuum suction lifting installations, in chip transporting installations and in other waste water and process pipes as long as
the media to be discharged do not damage the components or the health and safety of the personnel.
For other pipes, this document only applies if agreed with the relevant operators and following prior
consultation with the manufacturer.
This document contains a designation system for the different types of pipes and fittings for easy identification
of each component.
This document is only applicable in conjunction with EN 1123-1. It does not apply to the marking of products
for which EN 1123-1/A1 is applicable.

This standard specifies requirements, tests and quality control for longitudinally welded, hot-dip galvanized steel pipes and fittings with spigot and socket for use in waste water systems usually operating under gravity or at a low head of pressure. For the purposes of this standard, components are pipes, fittings, joints and seals. This standard is for components used for the discharge of: - domestic waste water; - surface water and - groundwater.

This European Standard specifies requirements, tests and quality control for longitudinally welded, stainless steel pipes and fittings with spigot and socket for use in waste water systems usually operating under gravity or at low head of pressure. For the purposes of this standard, components are pipes, fittings, joints and seals. This standard is for components used for the discharge of: - domestic waste water; - surface water and - goundwater.

This standard applies to pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems.  
It specifies dimensions and tolerances for pipes, fittings and pipe connectors and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements.  
This European Standard is only valid in connection with EN 1124-1. It does not apply to the marking of products. EN 1124-1/A1 applies to the marking.

This European Standard specifies requirements, dimensions and tolerances for pipes and fittings of longitudinally welded, stainless steel pipe with spigot and socket used for vacuum drainage systems inside and outside buildings and for gravity and vacuum drainage systems on ships and floating maritime structures)
-   above freeboard deck as long as the heeling is taken into account in the event of damage when installed above freeboard deck on passenger ships;
-   inside a watertight compartment below freeboard deck;
-   with direct connection to the outboard (not permitted below freeboard deck);
-   inside tanks as long as these are not filled with foreign media and are not cargo tanks.
On well-anchored maritime structures, this European Standard applies to pipes and fittings of longitudinally welded stainless steel pipe with spigot and socket used in drainage systems in the accommodation area.
NOTE   Pipes and fittings according to this European Standard may also be used in central vacuum cleaning installations, in vacuum suction lifting installations, in chip transporting installations and in other waste water and process pipes as long as the media to be discharged do not damage the components or the health and safety of the personnel.
For other pipes, this European Standard only applies if agreed with the relevant operators and following prior consultation with the manufacturer.
This European Standard contains a designation system for the different types of pipes and fittings for easy identification of each component.
This European Standard is only applicable in conjunction with EN 1124-1. It does not apply to the marking of products for which EN 1124-1/A1 is applicable.

This standard applies to pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals of the System X and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements. Note: System X is a system of pipes and fittings of longitudinally welded stainless steel pipes with two-step sockets.

This standard applies to pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings and pipe connectors and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements. This standard is only valid in connection with prEN 1124-1. This standard does not apply to the marking of products. prEN 1124-1 applies to the marking.

This standard applies to pipes and fittings of longitudinally welded, hot-dip galvanized steel pipes with spigot and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements. This standard is only valid in connection with prEN 1123-1.