kSIST FprEN 4800-004:2024

SLOVENSKI STANDARD
oSIST prEN 4800-004:2024
01-maj-2024
Aeronavtika - Titan in titanove zlitine - Tehnična specifikacija - 004. del: Žice
Aerospace series - Titanium and titanium alloys - Technical specification - Part 004: Wire
Luft- und Raumfahrt - Titan und Titanlegierungen - Technische Lieferbedingungen - Teil
004: Drähte
Série aérospatiale - Titane et alliages de titane - Spécification technique - Partie 004 :
Fils
Ta slovenski standard je istoveten z: prEN 4800-004
ICS:
49.025.30 Titan Titanium
oSIST prEN 4800-004:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 4800-004:2024
oSIST prEN 4800-004:2024
DRAFT
EUROPEAN STANDARD
prEN 4800-004
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2023
ICS 49.025.30 Will supersede EN 4800-004:2010
English Version
Aerospace series - Titanium and titanium alloys -
Technical specification - Part 004: Wire
Série aérospatiale - Titane et alliages de titane - Luft- und Raumfahrt - Titan und Titanlegierungen -
Spécification technique - Partie 004 : Fils Technische Lieferbedingungen - Teil 004: Drähte
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 4800-004:2023 E
worldwide for CEN national Members.

oSIST prEN 4800-004:2024
prEN 4800-004:2023 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Wording of order . 6
5 Health and safety . 7
6 Technical requirements . 7
6.1 General. 7
6.2 Qualification requirements . 7
6.3 Release requirements . 7
6.3.1 Release tests . 7
6.3.2 Retests . 8
6.3.3 Rejection . 8
6.3.4 Special tests . 8
6.3.5 Capability clause . 8
6.3.6 Statistical process control. 8
6.3.7 Inspection and test report . 8
6.4 Traceability . 9
Bibliography . 32

oSIST prEN 4800-004:2024
prEN 4800-004:2023 (E)
European foreword
This document (prEN 4800-004:2023) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 4800-004:2010.
oSIST prEN 4800-004:2024
prEN 4800-004:2023 (E)
Introduction
This document is part of the series of European metallic material standards for aerospace applications.
The general organization of this series is described in EN 4258.
oSIST prEN 4800-004:2024
prEN 4800-004:2023 (E)
1 Scope
This document specifies the requirements for the ordering, manufacture, testing, inspection and
delivery of titanium and titanium alloy wire. It is intended to be applied when referred to and in
conjunction with the European material standard unless otherwise specified on the drawing, order or
inspection schedule.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2002-001, Aerospace series — Metallic materials — Test methods — Part 001: Tensile testing at
ambient temperature
EN 2002-002, Aerospace series — Metallic materials — Test methods — Part 002: Tensile testing at
elevated temperature
EN 2002-005, Aerospace series — Test methods for metallic materials — Part 005: Uninterrupted creep
and stress-rupture testing
EN 2002-16, Aerospace series — Metallic materials — Test methods — Part 16: Non-destructive testing
— Penetrant testing
EN 2003-009, Aerospace series — Test methods — Titanium and titanium alloys — Part 009:
Determination of surface contamination
EN 2032-001, Aerospace series — Metallic materials — Part 001: Conventional designation
EN 2032-2, Aerospace series — Metallic materials — Part 2: Coding of metallurgical condition in delivery
condition
EN 2078, Aerospace series — Metallic materials — Manufacturing schedule, inspection schedule,
inspection and test report — Definition, general principles, preparation and approval
EN 2955, Aerospace series — Recycling of titanium and titanium alloy scrap
EN 3114-001, Aerospace series — Test method — Microstructure of (α + β) titanium alloy wrought
products — Part 001: General requirements
EN 3114-002, Aerospace series — Test method — Microstructure of (α + β) titanium alloy wrought
products — Part 002: Microstructure of bars, sections, forging stock and forgings
EN 3238, Aerospace series — Metallic materials — Test method — Shear test for wires and rivets
EN 3683, Aerospace series — Test methods — Titanium alloy wrought products — Determination of
primary α content — Point count method and line intercept method
EN 3684, Aerospace series — Test methods — Titanium alloy wrought products — Determination of β
transus temperature — Metallographic method

Published as ASD-STAN Standard at the date of publication of this document by Aerospace and Defence
industries Association of Europe — Standardization (ASD-STAN), https://www.asd-stan.org/.
oSIST prEN 4800-004:2024
prEN 4800-004:2023 (E)
EN 3976, Aerospace series — Titanium and titanium alloys — Test method — Chemical analysis for the
determination of hydrogen content
EN 4259, Aerospace series — Metallic materials — Definition of general terms
EN 9100, Quality Management Systems — Requirements for Aviation, Space and Defence Organizations
EN 9133, Aerospace series — Quality Management Systems — Qualification Procedure for Aerospace
Standard Products
EN ISO 643, Steels — Micrographic determination of the apparent grain size (ISO 643)
ISO 7800, Metallic materials — Wire — Simple torsion test
ISO 7801, Metallic materials — Wire — Reverse bend test
ISO 7802, Metallic materials — Wire — Wrapping test
ISO 9649, Metallic materials — Wire — Reverse torsion test
TR 2410, Aerospace series — Metallic materials — Relationship between dimensional standards and
material standards
AMS 2750, Pyrometry
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 4259 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
4 Wording of order
The order shall clearly indicate:
— quantities to be supplied;
— dates of delivery;
— material standard number;
— delivery condition and metallurgical code of products;
— dimensions and tolerances or reference to an appropriate dimensional standard;
— product designation, when required;
— forwarding address;
Published as ASD-STAN Technical Report at the date of publication of this document by AeroSpace and Defence
industries Association of Europe — Standardization (ASD-STAN), https://www.asd-stan.org/.
oSIST prEN 4800-004:2024
prEN 4800-004:2023 (E)
— nature and type of packing, if required;
— definition and frequency of any special tests and their retest procedures, if required.
5 Health and safety
The products in the delivery condition shall fulfil the health and safety laws of the area of the country
when and where it is to be delivered.
A product safety data sheet shall be available.
6 Technical requirements
6.1 General
The product shall be manufactured in accordance with the requirements of the relevant material
standard and the applicable requirements of this specification. A manufacturing schedule shall be
established and applied in accordance with EN 2078.
The product shall satisfy the requirements of the material standard and/or order and shall be free from
irregularities prejudicial to the subsequent manufacture or use of this product.
Notwithstanding previous acceptance complying with this material standard, any product that is found,
at a later stage, to contain such defects shall be rejected.
Unless otherwise specified, the requirements in Table 1 and Table 2 shall apply in conjunction with
those of the relevant material standard. Table 1 relates to lines 1 to 29 (inclusive) of the material
standard and Table 2 relates to lines 30 onwards in which the sub-line format is also used. Lines 2 to 98
may also be opened in line 100 if the material standard details specific qualification requirements. If a
specific line number is not shown in Table 1 and Table 2, the requirement is stated in the material
standard and/or order.
The requirements of the order and/or material standard shall over-ride the requirements of the
technical specification.
6.2 Qualification requirements
Qualification requirements when invoked by the material standard and/or order are detailed in Table 1
and Table 2. Unless otherwise agreed between the manufacturer and purchaser the qualification phase
shall be run on the first three batches, coming from three different ingots.
6.3 Release requirements
6.3.1 Release tests
Release testing shall be the responsibility of the manufacturer.
The purchaser reserves the right to perform any of the inspections and/or tests required by the
material standard and/or order.
The test samples shall be representative of the product.
When required the manufacturer shall inform the purchaser of the planned dates for extraction of
samples and release testing in order that these operations may be witnessed.
Table 1 and Table 2 detail the requirements for each line of the material standard. Unless otherwise
specifically requested by the purchaser, a particular inspection and/o
...