SIST EN 13523-17:2019
(Main)Coil coated metals - Test methods - Part 17: Adhesion of strippable films
Coil coated metals - Test methods - Part 17: Adhesion of strippable films
This part of the EN 13523 series specifies two methods for determining the numerical evaluation of the adhesion of strippable films which have previously been applied to an organic coating on a metallic substrate.
Samples can be tested irrespective of whether the strippable film has been applied in the laboratory or on the production line.
NOTE Method 1 is preferred for films with adhesive and method 2 for films without adhesive.
Bandbeschichtete Metalle - Prüfverfahren - Teil 17: Haftfestigkeit von abziehbaren Folien
Dieser Teil der Normenreihe EN 13523 legt zwei Verfahren zum zahlenmäßigen Bewerten der Haftfestigkeit von abziehbaren Folien fest, die auf eine organische Beschichtung auf einem metallischen Substrat auf¬gebracht wurden.
Es können Proben geprüft werden, unabhängig davon, ob die Folie im Laboratorium oder in der Produk-tionsanlage aufgebracht wurde.
ANMERKUNG Verfahren 1 wird bevorzugt für Folien mit Klebstoff und Verfahren 2 bevorzugt für Folien ohne Kleb-stoff angewandt.
Tôles prélaquées - Méthodes d'essai - Partie 17 : Adhérence des films pelables
La présente partie de la série EN 13523 spécifie deux méthodes de quantification de l’adhérence des films pelables préalablement appliqués sur un revêtement organique recouvrant un subjectile métallique.
L’essai peut être indifféremment effectué sur des échantillons dont le film pelable a été appliqué en laboratoire ou sur la chaîne de production.
NOTE La méthode 1 est préconisée pour les films comportant un adhésif et la méthode 2 pour ceux n’en comportant pas.
Prevlečene kovine, ki se navijajo - Preskusne metode - 17. del: Oprijemljivost zaščitnih folij
Ta del standarda EN 13523 določa dve metodi za določanje številskega vrednotenja oprijemljivosti zaščitnih folij, ki so bile pred tem nanesene na organski premaz na kovinski podlagi.
Vzorce je mogoče preskusiti ne glede na to, ali je bila zaščitna folija nanesena v laboratoriju ali na proizvodni liniji.
OPOMBA: Metoda 1 je primerna za folije z lepilom, metoda 2 pa za folije brez lepila.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13523-17:2019
01-november-2019
Nadomešča:
SIST EN 13523-17:2012
Prevlečene kovine, ki se navijajo - Preskusne metode - 17. del: Oprijemljivost
zaščitnih folij
Coil coated metals - Test methods - Part 17: Adhesion of strippable films
Bandbeschichtete Metalle - Prüfverfahren - Teil 17: Haftfestigkeit von abziehbaren Folien
Tôles prélaquées - Méthodes d'essai - Partie 17 : Adhérence des films pelables
Ta slovenski standard je istoveten z: EN 13523-17:2019
ICS:
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-17:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13523-17:2019
---------------------- Page: 2 ----------------------
SIST EN 13523-17:2019
EN 13523-17
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2019
EUROPÄISCHE NORM
ICS 25.220.60
English Version
Coil coated metals - Test methods - Part 17: Adhesion of
strippable films
Tôles prélaquées - Méthodes d'essai - Partie 17 : Bandbeschichtete Metalle - Prüfverfahren - Teil 17:
Adhérence des films pelables Haftfestigkeit von abziehbaren Folien
This European Standard was approved by CEN on 1 July 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-17 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13523-17:2019
EN 13523-17:2019 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 6
5.1 For method 1 . 6
5.2 For method 2 . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure. 6
8.1 Panel preparation . 6
8.1.1 Self-adhesive strippable film . 6
8.1.2 Non-adhesive strippable film . 7
8.2 Determination . 7
8.2.1 Method 1 . 7
8.2.2 Method 2 . 8
8.3 Evaluation and expression of results . 9
9 Precision . 9
10 Test report . 9
Bibliography . 10
2
---------------------- Page: 4 ----------------------
SIST EN 13523-17:2019
EN 13523-17:2019 (E)
European foreword
This document (EN 13523-17:2019) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2020, and conflicting national standards shall be withdrawn
at the latest by March 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-17:2011.
The main changes compared to EN 13523-17:2011 are:
a) in 8.2.1 and 8.2.2 tolerances have been added to the area for leaving the film;
b) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 15: Metamerism
3
---------------------- Page: 5 ----------------------
SIST EN 13523-17:2019
EN 13523-17:2019 (E)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environment
...
SLOVENSKI STANDARD
oSIST prEN 13523-17:2018
01-december-2018
3UHYOHþHQHNRYLQHNLVHQDYLMDMR3UHVNXVQHPHWRGHGHO 2SULMHPOMLYRVW
]DãþLWQLKIROLM
Coil coated metals - Test methods - Part 17: Adhesion of strippable films
Bandbeschichtete Metalle - Prüfverfahren - Teil 17: Haftfestigkeit von abziehbaren Folien
Tôles prélaquées - Méthodes d'essai - Partie 17 : Adhérence des films pelables
Ta slovenski standard je istoveten z: prEN 13523-17
ICS:
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-17:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13523-17:2018
---------------------- Page: 2 ----------------------
oSIST prEN 13523-17:2018
DRAFT
EUROPEAN STANDARD
prEN 13523-17
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2018
ICS 25.220.60 Will supersede EN 13523-17:2011
English Version
Coil coated metals - Test methods - Part 17: Adhesion of
strippable films
Tôles prélaquées - Méthodes d'essai - Partie 17 : Bandbeschichtete Metalle - Prüfverfahren - Teil 17:
Adhérence des films pelables Haftfestigkeit von abziehbaren Folien
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-17:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13523-17:2018
prEN 13523-17:2018 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 5
5.1 For method 1 . 5
5.2 For method 2 . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure. 6
8.1 Panel preparation . 6
8.1.1 Self-adhesive strippable film . 6
8.1.2 Non-adhesive strippable film . 6
8.2 Determination . 7
8.2.1 Method 1 . 7
8.2.2 Method 2 . 8
8.3 Evaluation and expression of results . 9
9 Precision . 9
10 Test report . 9
Bibliography . 11
2
---------------------- Page: 4 ----------------------
oSIST prEN 13523-17:2018
prEN 13523-17:2018 (E)
European foreword
This document (prEN 13523-17:2018) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13523-17:2011.
The main changes are:
a) tolerances have been added to the panel sizes;
b) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 15: Metamerism
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
3
---------------------- Page: 5 ----------------------
oSIST prEN 13523-17:2018
prEN 13523-17:2018 (E)
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.