SIST EN 60034-16-1:2011

SLOVENSKI STANDARD
01-september-2011
1DGRPHãþD
SIST EN 60034-16-1:1999
(OHNWULþQLURWDFLMVNLVWURMLGHO9]EXMDOQLVLVWHPL]DVLQKURQHVWURMH
'HILQLFLMH,(&
Rotating electrical machines - Part 16-1: Excitation systems for synchronous machines -
Definitions (IEC 60034-16-1:2011)
Drehende elektrische Maschinen - Teil 16-1: Erregersysteme für Synchronmaschinen -
Begriffe (IEC 60034-16-1:2011)
Machines électriques tournantes - Partie 16-1: Systèmes d'excitation pour machines
synchrones - Définitions (CEI 60034-16-1:2011)
Ta slovenski standard je istoveten z: EN 60034-16-1:2011
ICS:
29.160.01 Rotacijski stroji na splošno Rotating machinery in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60034-16-1
NORME EUROPÉENNE
July 2011
EUROPÄISCHE NORM
ICS 29.160 Supersedes EN 60034-16-1:1995

English version
Rotating electrical machines -
Part 16-1: Excitation systems for synchronous machines -
Definitions
(IEC 60034-16-1:2011)
Machines électriques tournantes -  Drehende elektrische Maschinen -
Partie 16-1: Systèmes d'excitation pour Teil 16-1: Erregersysteme für
machines synchrones - Synchronmaschinen -
Définitions Begriffe
(CEI 60034-16-1:2011) (IEC 60034-16-1:2011)

This European Standard was approved by CENELEC on 2011-06-29. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60034-16-1:2011 E
Foreword
The text of document 2/1598/CDV, future edition 2 of IEC 60034-16-1, prepared by IEC TC 2, Rotating
machinery, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60034-16-1 on 2011-06-29.
This European Standard supersedes EN 60034-16-1:1995.
The major technical changes with regard to EN 60034-16-1:1995 are as follows:
Clause or subclause Change
2.1.1 Additional definition for digital excitation system
2.1.2 Additional definition for reversible excitation system
2.3 Edited definition of excitation control
2.4 Additional definition for excitation control system. Added block diagram of
excitation control system
2.17 Additional definition for excitation system negative ceiling voltage U
n
2.19 Edited definition of excitation system on-load ceiling voltage U
pL
2.20 Additional definition for excitation system on-load negative ceiling voltage U
nL
2.22 Additional definition for excitation system voltage response time
2.23 Additional definition for high initial response excitation system
3.1 Edited definition of rotating exciter
3.1.2 Edited definition of AC exciter
3.2.3 Additional definition for auxiliary winding source static exciter
3.3 Additional definition for pilot exciter
4.1 to 4.7 Edited definitions of control functions
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2012-03-29
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2014-06-29
with the EN have to be withdrawn
__________
- 3 - EN 60034-16-1:2011
Endorsement notice
The text of the International Standard IEC 60034-16-1:2011 was approved by CENELEC as a European
Standard without any modification.
__________
IEC 60034-16-1 ®
Edition 2.0 2011-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Rotating electrical machines –
Part 16-1: Excitation systems for synchronous machines – Definitions

Machines électriques tournantes –
Partie 16-1: Systèmes d'excitation pour machines synchrones – Définitions

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX L
ICS 29.160 ISBN 978-2-88912-487-9

– 2 – 60034-16-1  IEC:2011
CONTENTS
FOREWORD . 3
1 Scope . 5
2 General . 5
3 Exciter categories . 10
4 Control functions . 11

Figure 1 – Block diagram of excitation control system . 6
Figure 2 – Determination of no-load field current I and air-gap field current I . 7
f0 fg
Figure 3 – Determination of excitation system nominal response, V . 9
e
60034-16-1  IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINES –

Part 16-1: Excitation systems for synchronous machines –
Definitions
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60034-16-1 has been prepared by IEC technical committee 2:
Rotating machinery.
This second edition cancels and replaces the first edition, issued in 1991, and constitutes a
technical revision.
The major technical changes with regard to the previous edition are as follows:
Clause or
Change
subclause
2.1.1 Additional definition for digital excitation system
2.1.2 Additional definition for reversible excitation system
2.3 Edited definition of excitation control

– 4 – 60034-16-1  IEC:2011
2.4 Additional definition for excitation control system. Added block diagram of
excitation control system
2.17 Additional definition for excitation system negative ceiling voltage U
n
2.19 Edited definition of excitation system on-load ceiling voltage U

pL
2.20 Additional definition for excitation system on-load negative ceiling voltage U
nL
2.22 Additional definition for excitation system voltage response time
2.23 Additional definition for high initial response excitation system
3.1 Edited definition of rotating exciter
3.1.2 Edited definition of AC exciter
Additional definition for auxiliary winding source static exciter
3.2.3
Additional definition for pilot exciter
3.3
Edited definitions of control functions
4.1 to 4.7
The text of this standard is based on the following documents:
CDV Report on voting
2/1598/CDV 2/1617/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
NOTE A table of cross-references of all IEC TC 2 publications can be found on the IEC TC 2 dashboard on the
IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
60034-16-1  IEC:2011 – 5 –
ROTATING ELECTRICAL MACHINES –

Part 16-1: Excitation systems for synchronous machines –
Definitions
1 Scope
This part of IEC 60034 defines terms applicable to the excitation systems of synchronous
rotating electrical machines.
2 General
2.1
excitation system
equipment providing the field current of a machine, including all regulating and control
elements, as well as field discharge or suppression equipment and protective devices
2.1.1
digital excitation system
excitation system of a machine where some, if not all, of regulating, control, limiting and
protective functionality is implemented using digital technology
NOTE As a minimum, the voltage regulation function must be implemented digitally in such a system.
2.1.2
reversible excitation system
excitation system providing compulsory change of sign of magnetic flux, created by a winding
or excitation windings of a synchronous machine
2.2
exciter
source of the electrical power, providi
...