oSIST prEN 15254-1:2005

SLOVENSKI oSIST prEN 15254-1:2005

PREDSTANDARD
julij 2005
Razširjena uporaba rezultatov preskusov požarne odpornosti - Nenosilne
stene - 1. del: Splošno
Extended application of results from fire resistance tests - Non- loadbearing walls -
Part 1: General
ICS 13.220.50 Referenčna številka
oSIST prEN 15254-1:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 15254-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2005
ICS
English version
Extended application of results from fire resistance tests - Non-
loadbearing walls - Part 1: General
Erweiterter Anwendungsbereich der Ergebnisse von
Feuerwiderstandsprüfungen - Nichttragende Wände - Teil
1: Allgemeine Grundlagen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 127.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15254-1:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 15254-1:2005 (E)
Contents Page
Foreword. 3
1 Scope. 4
2 Normative references. 4
3 Definitions. 6
4 Basis and methodology of establishing the extended application . 7
5 Critical parameters. 8
5.1 Common thermal parameters . 8
5.2 Common mechanical parameters . 8
5.3 Common constructional parameters. 8
6 Fire engineering rules for the establishing of the factor influences in a
quantitative manner. 8
6.1 General. 8
6.2 Thermal performance. 9
6.3 Structural performance. 9
7 Report of the extended application analysis .10
Annex A. 11

2

---------------------- Page: 3 ----------------------
prEN 15254-1:2005 (E)
Foreword
This document (prEN 15254-1:2005) has been prepared by Technical Committee CEN/TC 127 “Fire
safety in buildings”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative annex A, which is an integral part of this
document.

3

---------------------- Page: 4 ----------------------
prEN 15254-1:2005 (E)
1 Scope
This Part of prEN 15254-1 identifies the general parameters and factors that affect the fire resistance
of non-loadbearing walls (partitions) and need to be taken into account when considering extended
application of results of non-loadbearing walls tested in accordance with EN 1364: 1. It also defines
the general rules and principles to which can be applied to establish the resultant influence of a
variation in one or more parameters and to determine the limits of the field of extended application
together with the content of the report of the study. The standard is applicable to the following types of
non-loadbearing walls:
 Part 2
 Masonry and gypsum blocks:
 Concrete blocks
 Bricks
 Gypsum blocks
 Aerated concrete blocks
 Aerated concrete panels
 Part 3
 Lightweight partition:
 Boards + studs (metal or timber) + insulation + voids
 Part 4
 Glazed construction:
 Panes
 Part 5
 Metal sandwich panel construction
 Part 6
 Demountable partitions
Some examples of the above partitions are given in figures in the specific parts.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
4

---------------------- Page: 5 ----------------------
prEN 15254-1:2005 (E)
EN 1363, 1 Fire resistance tests — Part 1: General Requirements
EN 1363-2, Fire resistance tests — Part 2: Alternative and additional procedures
EN 1364-1, Fire resistance tests for non- load bearing elements — Part 1: Non - loadbearing walls
prEN 15254-1, Extended application of results from fire resistance tests — Part 1: General principles
EN 13502-2, Fire classification of construction products and building elements — Part 2: Classification
using data from fire resistance test (excluding products for use in ventilation systems)
ENV 1991-2-2, Eurocode 1. Basis of design and actions on structures — Part 2-2: Actions on
structures exposed to fire
ENV 1992-1-2, Eurocode 2. Design of concrete structures — Part 1-2: General rules. Structural fire
design
ENV 1993-1-2, Eurocode 3. Design of steel structures — Part 1-2: General rules. Structural fire
design
ENV 1994-1-2, Eurocode 4. Design of composite steel and concrete structures — Part 1-2: General
rules. Structural fire design
ENV 1995-1-2, Eurocode 5. Design of timber structures — Part 1-2: General rules. Structural fire
design
ENV 13381-2, Contribution to fire resistance of structural members — Part 3: Vertical membranes
ENV 13381-3, Contribution to fire resistance of structural members — Part 3: Concrete elements
ENV 13381-4, Contribution to fire resistance of structural members — Part 4: Steel elements
ENV 13381-7, Contribution to fire resistance of structural members — Part 7: Timber elements
ISO 13943, Fire safety - Vocabulary
5

---------------------- Page: 6 ----------------------
prEN 15254-1:2005 (E)
3 Definitions
For the purpose of this part of prEN 15254-1 the definitions given in EN ISO 13943, EN 1363-1, EN
1365-3 and prEN 15254-1, together with the following apply:
3.1
reference scenario
all the fire test conditions and constructional details of the test specimen for which observations of fire
behaviour, changes in temperatures, dimensions and displacement in the test specimen are given in
the test report
3.2
reference test
fire resistance test in accordance with EN 1364-1, and where applicable EN 1363-2, on which the
extended application is based and the results of which are used as the main source of data for the
extended application
3.3
test result
outcome of a testing process and its associated procedures detailed within a specific test standard
(which may include some processing of the results from the testing of a number of specimens). A test
result is expressed in terms of one or more fire performance parameter(s)
3.4
constructional parameter
aspect of the reference specimen that varies for the purpose of the prEN 15254-1 (other needs in
practice) and may change of the fire resistance performance
3.5
factor
one of the possible variations that may be applied to a parameter
3.6
factor influence
one of the potential causes of a change in the fire resistance due to a factor
3.7
direct field of application of test results
outcome of a process (involving the application of a defined rule) whereby a single test result,
expressed in terms of all the relevant fire performance parameters, is deemed to be equally valid for
variations in or more of the product properties
3.8
extended field of application of test results
outcome of the process (involving the application of defined rules that may incorporate calculation
procedures) that predicts the result of a test, expressed in terms of all the relevant fire performance
parameters, on the basis of one or more test results to the specific test method and related to the
particular product (including variations of the product properties)
3.9
classification
process defined in EN 13501-2, whereby the fire performance parameters obtained from the results of
one test, or a set of tests, or from a process of extended application, are compared with limiting
values for those parameters that are set as criteria for achieving a certain classific
...