SIST EN 60851-2:2010/A1:2015
(Amendment)Winding wires - Test methods - Part 2: Determination of dimensions
Winding wires - Test methods - Part 2: Determination of dimensions
WI created for possible future // procedure
Wickeldrähte - Prüfverfahren - Teil 2: Ermittlung der Maße
Fils de bobinage - Méthodes d'essai -- Partie 2: Détermination des dimensions
Navijalne žice - Preskusne metode - 2. del: Ugotavljanje mer - Dopolnilo A1
General Information
- Status
- Published
- Publication Date
- 13-Aug-2015
- Technical Committee
- I09 - Imaginarni 09
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 06-Aug-2015
- Due Date
- 11-Oct-2015
- Completion Date
- 14-Aug-2015
Relations
- Effective Date
- 01-Sep-2015
Overview
EN 60851-2:2009/A1:2015 (IEC 60851-2:2009/AMD1:2015) is a CENELEC/IEC amendment to the part of the EN/IEC 60851 series that specifies test methods for determination of dimensions of winding wires. The amendment (A1) updates measurement recommendations, adds provisions for paper-covered wires, and includes an informative annex giving the relationship between applied force and resulting pressure for typical measuring setups. The amendment was approved by CENELEC on 25 June 2015.
Key topics and requirements
- Scope: test methods for determining dimensional characteristics of winding wires (round, rectangular, covered types).
- Measurement equipment and parameters:
- Anvil diameter recommendations (typical values 5–8 mm shown for many wire types).
- Measuring force for various wire types (for example, enamelled rectangular, film-tape wrapped and fibrous covered wires are given typical measuring force ranges of about 2–4 N).
- For paper-covered wire, a measuring pressure (rather than a simple force) is specified (typical 1–2 N/mm), with a new Table 1c introduced in the amendment.
- Annex A (informative): provides a tabulated relationship between force (N), pressure (N/mm² or N/mm as used here), anvil diameter, and the effective rectangular contact surface; includes the formula p = F / A to convert force to pressure for any given contact area.
- The amendment leaves the original Part 2 procedures unchanged except for these clarified measurement parameters and the added guidance for paper-covered wires.
Applications and practical use
- Quality control and dimensional inspection of winding wires used in motors, transformers, inductors, and other electrical windings.
- Test laboratories and manufacturers use the standard to:
- Select appropriate anvil diameters and apply the correct measuring force/pressure for accurate diameter/thickness readings.
- Convert between force and pressure when measuring rectangular or paper-covered wires (using p = F/A and Annex A lookup tables).
- Procurement and compliance teams reference this standard when specifying dimensional test methods for supplier acceptance and product conformity.
Who should use this standard
- Wire manufacturers and converters (enamelled, tape-wrapped, fibrous- or paper-covered wires).
- Test laboratories and metrology technicians performing dimensional tests.
- R&D and quality assurance engineers in electrical equipment manufacturing where winding wire dimensions affect performance.
Related standards
- EN/IEC 60851 series (other parts cover electrical and physical test methods for winding wires).
- CENELEC/IEC publications relevant to wire testing and electrotechnical product standards.
Keywords: winding wires, test methods, determination of dimensions, EN 60851-2:2009/A1:2015, measuring force, measuring pressure, paper-covered wire, anvil diameter, Annex A, p = F/A.
Frequently Asked Questions
SIST EN 60851-2:2010/A1:2015 is a amendment published by the Slovenian Institute for Standardization (SIST). Its full title is "Winding wires - Test methods - Part 2: Determination of dimensions". This standard covers: WI created for possible future // procedure
WI created for possible future // procedure
SIST EN 60851-2:2010/A1:2015 is classified under the following ICS (International Classification for Standards) categories: 29.060.10 - Wires. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 60851-2:2010/A1:2015 has the following relationships with other standards: It is inter standard links to SIST EN 60851-2:2010. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 60851-2:2010/A1:2015 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2015
Navijalne žice - Preskusne metode - 2. del: Ugotavljanje mer - Dopolnilo A1
Winding wires - Test methods - Part 2: Determination of dimensions
Wickeldrähte - Prüfverfahren - Teil 2: Ermittlung der Maße
Fils de bobinage - Méthodes d'essai -- Partie 2: Détermination des dimensions
Ta slovenski standard je istoveten z: EN 60851-2:2009/A1:2015
ICS:
29.060.10 Žice Wires
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 60851-2:2009/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2015
ICS 29.060.10
English Version
Winding wires - Test methods - Part 2: Determination of
dimensions
(IEC 60851-2:2009/AMD1:2015)
Fils de bobinage - Méthodes d'essai - Partie 2: Wickeldrähte - Prüfverfahren - Teil 2: Ermittlung der Maße
Détermination des dimensions (IEC 60851-2:2009/AMD1:2015)
(IEC 60851-2:2009/AMD1:2015)
This amendment A1 modifies the European Standard EN 60851-2:2009; it was approved by CENELEC on 2015-06-25. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60851-2:2009/A1:2015 E
European foreword
The text of document 55/1520/FDIS, future IEC 60851-2:2009/A1, prepared by IEC/TC 55 "Winding
wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2016-03-25
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2018-06-25
• latest date by which the national standards conflicting with
the document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60851-2:2009/A1:2015 was approved by CENELEC as a
European Standard without any modification.
IEC 60851-2 ®
Edition 3.0 2015-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Winding wires – Test methods –
Part 2: Determination of dimensions
Fils de bobinage – Méthodes d'essai –
Partie 2: Détermination des dimensions
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-2688-9
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...