SIST EN 3745-506:2009
(Main)Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 506: Impact resistance
Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 506: Impact resistance
This standard specifies a method to determine the ability of an optical fibre or cable to withstand impact under specified environmental conditions.
Luft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 506: Fallprüfung
Diese Norm legt ein Verfahren zum Nachweis der Schlagfestigkeit eines Lichtwellenleiters oder Licht-wellenleiterkabels gegen Stöße unter vorgegebenen Umweltbedingungen fest.
Série aérospatiale - Fibres et câbles optiques à usage aéronautique - Méthodes d'essais - Partie 506: Résistance à l'impact
Aeronavtika - Optična vlakna in kabli za uporabo v zračnih plovilih - Preskusne metode - 506. del: Odpornost proti udarcu
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 506: FallprüfungSérie aérospatiale - Fibres et câbles optiques à usage aéronautique - Méthodes d'essais - Partie 506: Résistance à l'impactAerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 506: Impact resistance49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 3745-506:2009SIST EN 3745-506:2009en,de01-oktober-2009SIST EN 3745-506:2009SLOVENSKI
STANDARD
SIST EN 3745-506:2009
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3745-506
August 2009 ICS 49.060 English Version
Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 506: Impact resistance
Série aérospatiale - Fibres et câbles optiques à usage aéronautique - Méthodes d'essais - Partie 506: Résistance à l'impact
Luft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 506: Schlagfestigkeit This European Standard was approved by CEN on 3 July 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3745-506:2009: ESIST EN 3745-506:2009
EN 3745-506:2009 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Preparation of specimens .4 4 Apparatus .4 5 Method .5 5.1 Procedure .5 5.2 Final measurements and requirements .5
SIST EN 3745-506:2009
EN 3745-506:2009 (E) 3 Foreword This document (EN 3745-506:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accor
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.