SIST EN 13286-43:2004

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ungebundene und hydraulisch gebundene Gemische - Teil 43: Prüfverfahren zur Bestimmung des Elastizitätsmoduls hydraulaulisch gebundener GemischeMélanges traités et mélanges non traités aux liants hydraulique - Partie 43: Méthode d'essai pour la détermination du module d'élasticité des mélanges traités aux liants hydrauliquesUnbound and hydraulically bound mixtures - Part 43: Test method for the determination of the modulus of elasticity of hydraulically bound mixtures93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 13286-43:2003SIST EN 13286-43:2004en01-junij-2004SIST EN 13286-43:2004SLOVENSKI
STANDARD



SIST EN 13286-43:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13286-43March 2003ICS 93.080.20English versionUnbound and hydraulically bound mixtures - Part 43: Testmethod for the determination of the modulus of elasticity ofhydraulically bound mixturesMélanges traités et mélanges non traités aux liantshydraulique - Partie 43: Méthode d'essai pour ladétermination du module d'élasticité des graves traités auxliants hydrauliquesUngebundene und hydraulisch gebundene Gemische - Teil43: Prüfverfahren zur Bestimmung des Elastizitätsmodulshydrauliaulisch gebundener GemischeThis European Standard was approved by CEN on 29 November 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovak Republic, Spain, Sweden, Switzerland andUnited Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13286-43:2003 ESIST EN 13286-43:2004



EN 13286-43:2003 (E)2ContentspageForeword.31Scope.52Normative references.53Terms and definitions.54Determination of the modulus of elasticity by compression or by direct tensile test.54.1Principle.54.2Apparatus.64.2.1Testing machine.64.2.2Strain measuring device.64.3Preparation of the test specimen.84.4Test procedure.84.4.1Position of the strain measuring device on the specimen.84.4.2Positioning the specimen on the test machine and loading.84.5Data recording and calculation of the elastic modulus.85Determination of the modulus of elasticity by indirect tensile test.95.1Principle.95.2Apparatus.95.2.1Testing machine conforming to EN 13286-42.95.2.2Strain measuring device.95.3Preparation of the test specimen.115.4Test procedure.115.4.1Position the strain measuring device on the specimen.115.4.2Positioning the specimen in the press and loading.115.5Data recording.115.6Calculation of the elastic modulus.116Test report.12SIST EN 13286-43:2004



EN 13286-43:2003 (E)3ForewordThis document (EN 13286-43:2003) has been prepared by Technical Committee CEN/TC 227 "Road materials",the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by September 2003, and conflicting national standards shall be withdrawn at thelatest by December 2004.This European Standard is one of a series of standards as listed below.EN 13286-1, Unbound and hydraulically bound mixtures — Part 1: Test methods for laboratory reference densityand water content — Introduction, general requirements and sampling.prEN 13286-2, Unbound and hydraulically bound mixtures — Part 2: Test methods for laboratory reference densityand water content — Proctor compaction.EN 13286-3, Unbound and hydraulically bound mixtures — Part 3: Test methods for laboratory reference densityand water content — Vibrocompression with controlled parameters.EN 13286-4, Unbound and hydraulically bound mixtures — Part 4: Test methods for laboratory reference densityand water content — Vibrating hammer.EN 13286-5, Unbound and hydraulically bound mixtures — Part 5: Test methods for laboratory reference densityand water content — Vibrating table.prEN 13286-7, Unbound and hydraulically bound mixtures — Part 7: Cyclic load triaxial test for unbound mixtures.EN 13286-40, Unbound and hydraulically bound mixtures — Part 40: Test method for the determination of thedirect tensile strength of hydraulically bound mixtures.EN 13286-41, Unbound and hydraulically bound mixtures — Part 41: Test method for the determination of thecompressive of strength of hydraulically bound mixtures.EN 13286-42, Unbound and hydraulically bound mixtures — Part 42: Test method for the determination of theindirect tensile strength of hydraulically bound mixtures.EN 13286-43, Unbound and hydraulically bound mixtures — Part 43: Test method for the determination of themodulus of elasticity of hydraulically bound mixtures.prEN 13286-44, Unbound and hydraulically bound mixtures — Part 44: Test method for the determination of thealpha coefficient of vitrified blastfurnace slag.prEN 13286-45, Unbound and hydraulically bound mixtures — Part 45: Test method for the determination of theworkability period of hydraulically bound mixtures.prEN 13286-46, Unbound and hydraulically bound mixtures — Part 46: Test method for the determination of themoisture condition value.prEN 13286-47, Unbound and hydraulically bound mixtures — Part 47: Test method for the determination ofCalifornia bearing ratio, immediate bearing index and linear swelling.prEN 13286-48, Unbound and hydraulically bound mixtures — Part 48: Test method for the determination of thedegree of pulverisation.SIST EN 13286-43:2004



EN 13286-43:2003 (E)4prEN 13286-49, Unbound and hydraulically bound mixtures — Part 49: Test method for the determination of theaccelerated swelling of soil treated by lime and/or hydraulic binder.prEN 13286-50, Unbound and hydraulically bound mixtures — Part 50: Method for the manufacture of testspecimens of hydraulically bound mixtures using Proctor equipment or vibrating table compaction.prEN 13286-51, Unbound and hydraulically bound mixtures — Part 51: Method for the manufacture of testspecimens of hydraulically bound mixtures using vibrating hammer compaction.prEN 13286-52, Unbound and hydraulically bound mixtures — Part 52: Method for the manufacture of testspecimens of hydraulically bound mixtures using vibrocompression.prEN 13286-53, Unbound and hydraulically bound mixtures — Part 53: Method for the manufacture of testspecimens of hydraulically bound mixt
...