SIST EN 13523-20:2020
(Main)Coil coated metals - Test methods - Part 20: Foam adhesion
Coil coated metals - Test methods - Part 20: Foam adhesion
This European Standard describes a laboratory method for testing foam adhesion to an organic coating on a metallic substrate under dry and wet conditions.
Bandbeschichtete Metalle - Prüfverfahren - Teil 20: Haftfestigkeit von Schaum
Dieses Dokument legt ein Laborverfahren zum Prüfen der Haftfestigkeit von Schaum auf einer organischen Beschichtung auf einem metallischen Substrat im trockenen und im nassen Zustand fest.
Tôles prélaquées - Méthodes d'essai - Partie 20: Adhérence des mousses
Le présent document décrit une méthode d’essai en laboratoire permettant de déterminer l’adhérence des mousses à un revêtement organique recouvrant un subjectile métallique, dans des conditions sèches et dans des conditions humides.
Prevlečene kovine, ki se navijajo - Preskusne metode - 20. del: Oprijemljivost pene
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13523-20:2020
01-september-2020
Nadomešča:
SIST EN 13523-20:2012
Prevlečene kovine, ki se navijajo - Preskusne metode - 20. del: Oprijemljivost pene
Coil coated metals - Test methods - Part 20: Foam adhesion
Bandbeschichtete Metalle - Prüfverfahren - Teil 20: Haftfestigkeit von Schaum
Tôles prélaquées - Méthodes d'essai - Partie 20: Adhérence des mousses
Ta slovenski standard je istoveten z: EN 13523-20:2020
ICS:
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-20:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13523-20:2020
---------------------- Page: 2 ----------------------
SIST EN 13523-20:2020
EN 13523-20
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-20:2011
English Version
Coil coated metals - Test methods - Part 20: Foam
adhesion
Tôles prélaquées - Méthodes d'essai - Partie 20 : Bandbeschichtete Metalle - Prüfverfahren - Teil 20:
Adhérence des mousses Haftfestigkeit von Schaum
This European Standard was approved by CEN on 3 May 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-20:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13523-20:2020
EN 13523-20:2020 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Material . 5
6 Apparatus . 5
7 Sampling . 5
8 Test panels . 6
9 Procedure. 6
9.1 Preparation . 6
9.2 Adhesion testing . 6
9.2.1 Dry adhesion . 6
9.2.2 Wet adhesion . 6
9.2.3 Testing non-adhesion in domestic appliance products . 6
10 Expression of results . 6
11 Precision . 7
12 Test report . 7
Bibliography . 8
2
---------------------- Page: 4 ----------------------
SIST EN 13523-20:2020
EN 13523-20:2020 (E)
European foreword
This document (EN 13523-20:2020) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2020, and conflicting national standards shall be
withdrawn at the latest by December 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-20:2011.
The main changes are:
a) testing of non-adhesion in domestic appliance products has been added (9.2.3);
b) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistanc
...
SLOVENSKI STANDARD
oSIST prEN 13523-20:2019
01-julij-2019
Prevlečene kovine, ki se navijajo - Preskusne metode - 20. del: Oprijemljivost pene
Coil coated metals - Test methods - Part 20: Foam adhesion
Bandbeschichtete Metalle - Prüfverfahren - Teil 20: Haftfestigkeit von Schaum
Tôles prélaquées - Méthodes d'essai - Partie 20: Adhérence des mousses
Ta slovenski standard je istoveten z: prEN 13523-20
ICS:
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-20:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13523-20:2019
---------------------- Page: 2 ----------------------
oSIST prEN 13523-20:2019
DRAFT
EUROPEAN STANDARD
prEN 13523-20
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2019
ICS 25.220.60 Will supersede EN 13523-20:2011
English Version
Coil coated metals - Test methods - Part 20: Foam
adhesion
Tôles prélaquées - Méthodes d'essai - Partie 20: Bandbeschichtete Metalle - Prüfverfahren - Teil 20:
Adhérence des mousses Haftfestigkeit von Schaum
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-20:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13523-20:2019
prEN 13523-20:2019 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Material . 5
6 Apparatus . 5
7 Sampling . 5
8 Test panels . 6
9 Procedure. 6
9.1 Preparation . 6
9.2 Adhesion testing . 6
9.2.1 Dry adhesion . 6
9.2.2 Wet adhesion . 6
9.2.3 Testing non-adhesion in domestic appliance products . 6
10 Expression of results . 6
11 Precision . 7
12 Test report . 7
Bibliography . 8
2
---------------------- Page: 4 ----------------------
oSIST prEN 13523-20:2019
prEN 13523-20:2019 (E)
European foreword
This document (prEN 13523-20:2019) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13523-20:2011.
The main changes are:
a) Testing of non-adhesion in domestic appliance products has been added (9.2.3);
b) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference — Instrument
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.