SIST EN IEC 62037-7:2023

SLOVENSKI STANDARD
SIST EN IEC 62037-7:2023
01-februar-2023
Pasivne radiofrekvenčne (RF) in mikrovalovne naprave, meritve
intermodulacijskega nivoja - 7. del: Terenska merjenja pasivne intermodulacije
(IEC 62037-7:2022)
Passive rf and microwave devices, intermodulation level measurement - Part 7: Field
measurements of passive intermodulation (IEC 62037-7:2022)
Passive HF- und Mikrowellenbauteile, Messung des Intermodulationspegels - Teil 7:
Feldmessungen der passiven Intermodulation (IEC 62037-7:2022)
Dispositifs RF et à micro-ondes passifs, mesure du niveau d’intermodulation - Partie 7:
Mesures de l’intermodulation passive sur le terrain (IEC 62037-7:2022)
Ta slovenski standard je istoveten z: EN IEC 62037-7:2022
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 62037-7:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62037-7:2023

---------------------- Page: 2 ----------------------
SIST EN IEC 62037-7:2023


EUROPEAN STANDARD EN IEC 62037-7

NORME EUROPÉENNE

EUROPÄISCHE NORM December 2022
ICS 33.120.01

English Version
Passive rf and microwave devices, intermodulation level
measurement - Part 7: Field measurements of passive
intermodulation
(IEC 62037-7:2022)
Dispositifs rf et à micro-ondes passifs, mesure du niveau Passive HF- und Mikrowellenbauteile, Messung des
d'intermodulation - Partie 7: Mesures de l'intermodulation Intermodulationspegels - Teil 7: Feldmessungen der
passive sur le terrain passiven Intermodulation
(IEC 62037-7:2022) (IEC 62037-7:2022)
This European Standard was approved by CENELEC on 2022-12-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62037-7:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62037-7:2023
EN IEC 62037-7:2022 (E)
European foreword
The text of document 46/903/FDIS, future edition 1 of IEC 62037-7, prepared by IEC/TC 46 "Cables,
wires, waveguides, RF connectors, RF and microwave passive components and accessories" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 62037-7:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-09-02
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-12-02
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62037-7:2022 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 62037-7:2023
EN IEC 62037-7:2022 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 62037-1 2021 Passive RF and microwave devices, EN IEC 62037-1 2021
intermodulation level measurement - Part
1: General requirements and measuring
methods
IEC 62037-2 2021 Passive RF and microwave devices, EN IEC 62037-2 2021
intermodulation level measurement - Part
2: Measurement of passive intermodulation
in coaxial cable assemblies
IEC 62037-3 2021 Passive RF and microwave devices, EN IEC 62037-3 2021
intermodulation level measurement - Part
3: Measurement of passive intermodulation
in coaxial connectors
IEC 62037-5 2021 Passive RF and microwave devices, EN IEC 62037-5 2021
intermodulation level measurement - Part
5: Measurement of passive intermodulation
in filters
IEC 62037-6 2021 Passive RF and microwave devices, EN IEC 62037-6 2022
intermodulation level measurement - Part
6: Measurement of passive intermodulation
in antennas

3

---------------------- Page: 5 ----------------------
SIST EN IEC 62037-7:2023

---------------------- Page: 6 ----------------------
SIST EN IEC 62037-7:2023



IEC 62037-7

®


Edition 1.0 2022-10




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Passive rf and microwave devices, intermodulation level measurement –

Part 7: Field measurements of passive intermodulation



Dispositifs rf et à micro-ondes passifs, mesure du niveau d’intermodulation –

Partie 7: Mesures de l’intermodulation passive sur le terrain
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.01 ISBN 978-2-8322-5883-5




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 62037-7:2023
– 2 – IEC 62037-7:2022 © IEC 2022
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviated terms . 5
3.1 Terms and definitions . 5
3.2 Abbreviated terms . 6
4 General considerations . 6
4.1 Test environment . 6
4.2 Test frequencies . 6
4.3 Safety . 6
5 Field PIM test equipment . 7
6 Test procedure . 7
6.1 General . 7
6.2 Equipment verification . 7
6.2.1 General . 7
6.2.2 Clean and inspect RF connections . 7
6.2.3 Residual PIM test . 7
6.2.4 PIM standard test . 7
6.3 VSWR verification . 8
6.4 Interference verification . 8
6.5 Static PIM test . 8
6.6 Dynamic PIM test . 8
6.6.1 General . 8
6.6.2 Coaxial cable assemblies . 9
6.6.3 Coaxial connectors . 9
6.6.4 Splitters, combiners, filters and receive low noise amplifiers . 9
6.6.5 Antennas . 9
7 Test specification . 9
8 Report . 9
Annex A (informative) Distance-to-PIM measurements . 10


Figure A.1 – Internal vs. external PIM sources . 11

---------------------- Page: 8 ----------------------
SIST EN IEC 62037-7:2023
IEC 62037-7:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

PASSIVE RF AND MICROWAVE DEVICES,
INTERMODULATION LEVEL MEASUREMENT –

Part 7: Field measurements of passive intermodulation

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 62037-7 has been prepared by IEC technical committee 46: Cables, wires, waveguides, RF
connectors, RF and microwave passive components and accessories. It is an International
Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
46/903/FDIS 46/912/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

---------------------- Page: 9 ----------------------
SIST EN IEC 62037-7:2023
– 4 – IEC 62037-7:2022 © IEC 2022
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts of the IEC 62037 series, under the general title: Passive RF and microwave
devices, intermodulation level measurement, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 10 ----------------------
SIST EN IEC 62037-7:2023
IEC 62037-7:2022 © IEC 2022 – 5 –
PASSIVE RF AND MICROWAVE DEVICES,
INTERMODULATION LEVEL MEASUREMENT –

Part 7: Field measurements of passive intermodulation



1 Scope
This part of IEC 62037 defines test methods for reverse measurement of passive
intermodulation (PIM) in systems of RF components deployed in the field. Field PIM
measurements can be conducted on RF systems terminated into low PIM loads or on antenna
feed systems that broadcast the test signals into the environment.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 62037-1:2021, Passive RF and microwave devices, intermodulation level measurement –
Part 1: General requirements and measuring methods
IEC 62037-2:2021, Passive RF and microwave devices, intermodulation level measurement –
Part 2: Measurement of passive intermodulation in coaxial cable assemblies
IEC 62037-3:2021, Passive RF and microwave devices, intermodulation level measurement –
Part 3: Measurement of passive intermodulation in coaxial connectors
IEC 62037-5:2021, Passive RF and microwave devices, intermodulation level measurement –
Part 5: Measurement of passive intermodulation in filters
IEC 62037-6:2021, Passive RF and microwave devices, intermodulation level measurement –
Part
...