SIST EN ISO 18082:2014

SLOVENSKI STANDARD
01-oktober-2014
1DGRPHãþD
SIST EN 15908:2010
$QHVWH]LMVNDLQGLKDOQDRSUHPD0HUHQL]NRWODþQLKSULNOMXþNRY]QDYRMHPNLVHQH
PHQMDMR]DGHOR]PHGLFLQVNLPLSOLQL1,67,62
Anaesthetic and respiratory equipment - Dimensions of non-interchangeable screw-
threaded (NIST) low-pressure connectors for medical gases (ISO 18082:2014)
Anästhesie- und Beatmungsgeräte - Maße von nichtverwechselbaren
Verbindungsstücken mit Schraubgewinde (NIST) für niedrigen Druck zur Verwendung
mit medizinischen Gasen (ISO 18082:2014)
Matériel d'anesthésie et de réanimation respiratoire - Dimensions des raccords basse
pression à tête filetée non interchangeables (NIST) pour gaz médicaux (ISO
18082:2014)
Ta slovenski standard je istoveten z: EN ISO 18082:2014
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 18082
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 11.040.10 Supersedes EN 15908:2010
English Version
Anaesthetic and respiratory equipment - Dimensions of non-
interchangeable screw-threaded (NIST) low-pressure connectors
for medical gases (ISO 18082:2014)
Matériel respiratoire et anesthésique - Raccords basse Anästhesie- und Beatmungsgeräte - Maße von
pression à tête filetée non interchangeables (NIST) pour nichtverwechselbaren Verbindungsstücken mit
gaz médicaux (ISO 18082:2014) Schraubgewinde (NIST) für niedrigen Druck zur
Verwendung mit medizinischen Gasen (ISO 18082:2014)
This European Standard was approved by CEN on 22 May 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18082:2014 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 18082:2014) has been prepared by Technical Committee ISO/TC 121 “Anaesthetic
and respiratory equipment” in collaboration with Technical Committee CEN/TC 215 “Respiratory and
anaesthetic equipment” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn
at the latest by December 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15908:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18082:2014 has been approved by CEN as EN ISO 18082:2014 without any modification.
INTERNATIONAL ISO
STANDARD 18082
First edition
2014-06-15
Anaesthetic and respiratory
equipment — Dimensions of non-
interchangeable screw-threaded
(NIST) low-pressure connectors for
medical gases
Matériel respiratoire et anesthésique — Raccords basse pression à
tête filetée non interchangeables (NIST) pour gaz médicaux
Reference number
ISO 18082:2014(E)
©
ISO 2014
ISO 18082:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

ISO 18082:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Terms and definitions . 1
3 Dimensions and allocation of NIST connectors . 2
4 Marking .11
5 Test for durability of markings .11
Bibliography .12
ISO 18082:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 121, Anaesthetic and respiratory equipment,
Subcommittee SC 1, Breathing attachments and anaesthetic machines.
This is the first edition of this International Standard that contains the requirements for non-
interchangeable screw threaded (NIST) connectors for use with medical gases previously included in
ISO 5359:2008 and ISO 5359:2008/Amd.1:2011.
iv © ISO 2014 – All rights reserved

ISO 18082:2014(E)
Introduction
This International Standard has been prepared in response to the need for a safe method of connecting
medical equipment intended to administer medical gases to patients or power medical devices.
Medical gases are stored in cylinders or cryogenic vessels, or can be produced on site; several medical
devices (e.g. pressure regulators, hose assemblies, flow-metering devices, lung ventilators, anaesthetic
workstations) can be fitted between the source of supply and the medical device. At each interface gas-
specific connectors are needed to ensure that the intended medical gas is administered to the patient.
While the desirability of achieving agreement on a single International Standard for screw-threaded
connectors has never been in doubt, the present pattern of usage has made such agreement impossible.
Nevertheless, fears that proliferation of individual national standards or practices will eventually result
in potentially dangerous cross-connection between components for different gases have led to the choice
of several different connector systems, all of which are intended to be incompatible with each other.
This International Standard specifies the dimensions and the allocation of non-interchangeable screw
threaded (NIST) connectors for use with medical gases.
This International Standard does not specify the dimensions and the allocation of
[9]
— diameter index safety system (DISS) connectors specified in CGA V-5 ,
[7]
— sleeve inde
...