iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12341:2000

(Main)

Air quality - Determination of the PM 10 fraction of suspended particulate matter - Reference method and field test procedure to demonstrate reference equivalence of measurement methods

Air quality - Determination of the PM 10 fraction of suspended particulate matter - Reference method and field test procedure to demonstrate reference equivalence of measurement methods

This standard specifies the performance of PM10 sampling instruments in order to harmonize the monitoring within the framework of the European Union Council Directive 96/62/EC (2) on ambient air quality assessment and management, and the first daughter directive. In the daughter directive, by convention the ISO thoracic sampling convention has been assimilated to the PM10 fraction (see annex A; (3)).

Luftbeschaffenheit - Ermittlung der PM10-Fraktion von Schwebstaub - Referenzmethode und Feldprüfverfahren zum Nachweis der Gleichwertigkeit von Meßverfahren und Referenzmeßmethode

Diese Norm legt die Leistungsmerkmale von PM10-Probenahmegeräten fest, um die meßtechnische Überwachung im Rahmen der Richtlinie 96/62/EC des Rates der Europäischen Union über die Beurteilung und Kontrolle der Luftqualität (2) sowie der ersten Tochterrichtlinie zu vereinheitlichen. In der Tochterrichtlinie werden aufgrund einer Vereinbarung die Probenahme-Konvention für die thorakale Fraktion nach ISO und die PM10-Fraktion (siehe Anhang A; (3))im gleichen Sinne verwendet.

Qualité de l'air - Détermination de la fraction MP10 de matiere particulaire en suspension - Méthode de référence et procédure d'essai in situ pour démontrer l'équivalence a la référence de méthodes de mesurage

La présente norme spécifie les performances des instruments d'échantillonnage de la fraction MP10 pour harmoniser la surveillance selon la directive du Conseil de l'Union Européenne 96/62/CE (2) relative a l'évaluation et a la gestion de la qualité de l'air et selon la directive fille. Dans la directive fille, par convention, la convention d'échantillonnage thoracique de l'ISO a été assimilée a la fraction MP10 (voir annexe A (3)).

Kakovost zraka – Določevanje frakcije PM10 ledbečih trdnih delcev – Referenčna metoda in terenski preskusni postopek za potrditev ustreznosti merilnih metod

General Information

Status
Withdrawn
Publication Date
31-Dec-1999
Withdrawal Date
20-May-2014
ICS
13.040.20 - Ambient atmospheres
Technical Committee
KAZ - Air quality
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-May-2014
Due Date
12-Jun-2014
Completion Date
21-May-2014
Directive
1999/30/EC - Limit values for sulphur dioxide, nitrogen dioxide and oxides of nitrogen, particulate matter and lead in ambient air
96/62/EC - Ambient air quality assessment and management
Mandate
M/003 - Mandate for standardization by CEN - Test procedure allowing to show in real conditions the equivalence of the sampling procedures of the fine particles (up to 10 um) suspended in the ambient air in conformity with the Community directives
Ref Project
EN 12341:1998 - Air quality - Determination of the PM 10 fraction of suspended particulate matter - Reference method and field test procedure to demonstrate reference equivalence of measurement methods

Relations

Replaced By
SIST EN 12341:2014 - Ambient air - Standard gravimetric measurement method for the determination of the PM10 or PM2,5 mass concentration of suspended particulate matter
Effective Date
01-Jul-2014

Buy Standard

EN 12341:2000EN 12341:2000
PreviousNext
Standard
EN 12341:2000
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luftbeschaffenheit - Ermittlung der PM10-Fraktion von Schwebstaub - Referenzmethode und Feldprüfverfahren zum Nachweis der Gleichwertigkeit von Meßverfahren und ReferenzmeßmethodeQualité de l'air - Détermination de la fraction MP10 de matiere particulaire en suspension - Méthode de référence et procédure d'essai in situ pour démontrer l'équivalence a la référence de méthodes de mesurageAir quality - Determination of the PM 10 fraction of suspended particulate matter - Reference method and field test procedure to demonstrate reference equivalence of measurement methods13.040.20Kakovost okol
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST ISO 16000-3:2023(Main)
Indoor air - Part 3: Determination of formaldehyde and other carbonyl compounds in indoor and test chamber air - Active sampling method
ISO 16000-3:2022

This document specifies a determination of formaldehyde (HCHO) and other carbonyl compounds (aldehydes and ketones) in air. The method is specific to formaldehyde but, with modification, at least 12 other aromatic as well as saturated and unsaturated aliphatic carbonyl compounds can be detected and quantified. It is suitable for determination of formaldehyde and other carbonyl compounds in the approximate concentration range 1 µg/m3 to 1 mg/m3. The sampling method gives a time-weighted average (TWA) sample. It can be used for long-term (1 h to 24 h) or short-term (5 min to 60 min) sampling of air for formaldehyde.
This document specifies a sampling and analysis procedure for formaldehyde and other carbonyl compounds that involves collection from air on to adsorbent cartridges coated with 2,4-dinitrophenylhydrazine (DNPH) and subsequent analysis of the hydrazones formed by high performance liquid chromatography (HPLC) with detection by ultraviolet absorption[12],[16]. The method is not suitable for longer chained or unsaturated carbonyl compounds.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    29 pages
    French language
    sale 15% off
  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12341:2023(Main)
Ambient air - Standard gravimetric measurement method for the determination of the PM10 or PM2,5 mass concentration of suspended particulate matter
EN 12341:2023

This European Standard describes a standard method for determining the PM10 or PM2,5 mass concentrations of suspendedparticulate matter in ambient air by sampling the particulate matter on filters and weighing them by means of a balance.
Measurements are performed with samplers with inlet designs as specified in Annex A, operating at a nominal flow rate of 2,3 m3/h,over a nominal sampling period of 24 h. Measurement results are expressed in μg/m3, where the volume of air is the volume atambient conditions near the inlet at the time of sampling.
The range of application of this European Standard is for 24 h measurements from approximately 1 μg/m3 (i.e. the limit of detection ofthe standard measurement method expressed as its uncertainty) up to 150 μg/m3 for PM10 and 120 μg/m3 for PM2,5.
This European Standard describes procedures and gives requirements for the testing and use of so-called sequential samplers,equipped with a filter changer, suitable for extended stand-alone operation. Sequential samplers are commonly used throughout theEuropean Union for the measurement of concentrations in ambient air of PM10 or PM2,5. However, this European Standard does notexclude the use of single-filter samplers.
This European Standard represents an evolution of earlier European Standards (EN 12341:1998 and 2014, EN 14907:2005). Newequipment procured shall comply fully with this European Standard.
Older versions of these samplers, including those described in EN 12341:2014 Annex B, have a special status in terms of their use. These samplers can still be used for monitoring purposes and for ongoing quality control, provided that a well justified additionalallowance is made to their uncertainties
This European Standard also provides guidance for the selection and testing of filters with the aim of reducing the measurementuncertainty of the results obtained when applying this European Standard.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 16000-6:2023(Main)
Indoor air - Part 6: Determination of organic compounds (VVOC, VOC, SVOC) in indoor and test chamber air by active sampling on sorbent tubes, thermal desorption and gas chromatography using MS or MS FID
ISO 16000-6:2021

This document specifies a method for determination of volatile organic compounds (VOC) in indoor air and in air sampled for the determination of the emission from products or materials used in indoor environments (according to ISO 16000‑1) using test chambers and test cells. The method uses sorbent sampling tubes with subsequent thermal desorption (TD) and gas chromatographic (GC) analysis employing a capillary column and a mass spectrometric (MS) detector with or without an additional flame ionisation detector (FID)[13].
The method is applicable to the measurement of most GC-compatible vapour-phase organic compounds at concentrations ranging from micrograms per cubic metre to several milligrams per cubic metre. Many very volatile organic compounds (VVOC) and semi-volatile organic compounds (SVOC) can be analysed depending on the sorbents used.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    36 pages
    English language
    sale 15% off
  • Standard
    39 pages
    French language
    sale 15% off
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    37 pages
    English language
    sale 15% off
  • Draft
    39 pages
    French language
    sale 15% off
SIST
SIST ISO 12219-1:2023(Main)
Interior air of road vehicles - Part 1: Whole vehicle test chamber - Specification and method for the determination of volatile organic compounds in cabin interiors
ISO 12219-1:2021

This document specifies the whole vehicle test chamber, the vapour sampling assembly and the operating conditions for the determination of volatile organic compounds (VOCs), and carbonyl compounds in vehicle cabin air. There are three measurements performed: one (for VOCs and carbonyl compounds) during the simulation of ambient conditions (ambient mode) at standard conditions of 23 °C - 25 °C with no air exchange; a second only for the measurement of formaldehyde at elevated temperatures (parking mode); and a third for VOCs and carbonyl compounds simulating driving after the vehicle has been parked in the sun starting at elevated temperatures (driving mode). For the simulation of the mean sun irradiation, a fixed irradiation in the whole vehicle test chamber is employed.
The VOC method is valid for measurement of non-polar and slightly polar VOCs in a concentration range of sub-micrograms per cubic metre up to several milligrams per cubic metre. Using the principles specified in this method, some semi-volatile organic compounds (SVOC) can also be analysed. Compatible compounds are those which can be trapped and released from the Tenax TA®[1] sorbent tubes described in ISO 16000‑6, which includes VOCs ranging in volatility from n-C6 to n-C16.
The sampling and analysis procedure for formaldehyde and other carbonyl compounds is performed by collecting air on to cartridges coated with 2,4-dinitrophenylhydrazine (DNPH) and subsequent analysis by high performance liquid chromatography (HPLC) with detection by ultraviolet absorption. Formaldehyde and other carbonyl compounds can be determined in the approximate concentration range 1 µg/m3 to 1 mg/m3.
The method is valid for passenger cars, as defined in ECE-TRANS-WP.29/1045.
This document gives guidelines for:
a) transport and storage of the test vehicles until the start of the test;
b) conditioning for the surroundings of the test vehicle and the test vehicle itself as well as the whole vehicle test chamber;
c) conditioning of the test vehicle prior to measurements;
d) simulation of ambient air conditions (ambient mode);
e) formaldehyde sampling at elevated temperatures (parking mode);
f) simulation of driving after the test vehicle has been parked in the sun (driving mode).
  
[1] Tenax TA® is the trade name of a product supplied by Buchem. This information is given for the convenience of users of this document and does not constitute an endorsement by ISO of the product named. Equivalent products may be used if they can be shown to lead to the same results.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    29 pages
    English language
    sale 15% off
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 15% off
SIST
SIST-TS CEN/TS 17660-1:2022(Main)
Air quality - Performance evaluation of air quality sensor systems - Part 1: Gaseous pollutants in ambient air
CEN/TS 17660-1:2021

This Technical Specification (TS) describes the general principles, including testing procedures and requirements, for the evaluation of performances of low-cost sensor systems for the monitoring of gaseous compounds in ambient air at fixed sites. The evaluation of sensor systems includes tests that shall be performed under prescribed laboratory and/or field conditions.
This TS is not intended for the test of sensors systems used for mobile devices, for the testing of networks of sensor nodes, or for indoor air monitoring although their potential importance is recognized and they could be the subjects of future TS documents.
Low-cost sensors are based on several principles of operations, e. g. amperometric sensors, metal oxides, optical sensors (Infra-Red absorption) etc. However, sensors share some common features, regarding their portability and low-cost compared to traditional reference methods. Typically, sensors are able to continuously monitor air pollution, with low response time ranging between a few tens of seconds and a few minutes.
The described procedure is applicable to the determination of the mass concentration of air pollutants. The pollutants that are considered in this TS consists of:
-the gaseous pollutants regulated under Directives 2008/50/EC: O3, NO2 and NO, CO, SO2 and benzene, in the range of concentrations expected in outdoor ambient air;
-CO2 as proxy for activities involving combustion processes or for CO2 evaporation from soil or water.
When applying the current Technical Specifications, the evaluation of sensors considers the thresholds, limits and averaging times that are defined into the Air Quality Directive (2008/50/EC)[1]. Generally, the Directive sets Limit Values consists of an annual average that is computed by averaging hourly values. For sensors, it can be useful to select shorter averaging time.
In order to rely on the results of tests this protocol, future users shall make sure that sensors will be implemented with the same configuration as the sensor submitted to this protocol. This can include: the same power supply, data acquisition, data processing, identical sampling/ protective box and periodicity of calibration. The sensor shall be submitted to the same regime of QA/QC and maintenance operation as during tests. In addition, it is strongly recommended that sensors measurements are periodically compared side-by-side with the reference method.
For the purpose of this technical specification sensor systems are significantly less expensive than reference methods for the same pollutant.

  • Technical specification
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 12219-10:2021(Main)
Interior air of road vehicles - Part 10: Whole vehicle test chamber - Specification and methods for the determination of volatile organic compounds in cabin interiors - Trucks and buses
ISO 12219-10:2021

This document describes and specifies the whole vehicle test chamber, the vapour sampling assembly and the operating conditions for the determination of volatile organic compounds (VOCs; for more information see Annex E), and carbonyl compounds in vehicle cabin air. There are three measurements performed: one (for VOCs and carbonyl compounds) during the simulation of ambient conditions (ambient mode) at standard conditions of 23 °C with no air exchange; a second only for the measurement of formaldehyde at elevated temperatures (parking mode); and a third for VOCs and carbonyl compounds simulating driving after the vehicle has been parked in the sun starting at elevated temperatures (driving mode). For the simulation of the mean sun irradiation, fixed irradiation in the whole vehicle test chamber is employed.
The VOC method is valid for measurement of non-polar and slightly polar VOCs in a concentration range of sub-micrograms per cubic metre up to several milligrams per cubic metre. Using the principles described in this method, some semi-volatile organic compounds (SVOC) can also be analysed. Compatible compounds are those which can be trapped and released from the Tenax TA®1) sorbent tubes described in ISO 16000‑6, which includes VOCs ranging in volatility from n-C6 to n-C16.
The sampling and analysis procedure for formaldehyde and other carbonyl compounds is performed by collecting air on to cartridges coated with 2,4-dinitrophenylhydrazine (DNPH) and subsequent analysis by high performance liquid chromatography (HPLC) with detection by ultraviolet absorption. Formaldehyde and other carbonyl compounds can be determined in the approximate concentration range 1Â ÎĽg/m3 to 1Â mg/m3.
This method applicable to trucks and buses, as defined in ISOÂ 3833:1977 3.1.1 to 3.1.6.
This document describes:
a) Transport and storage of the test vehicle until the start of the test.
b) Conditioning of the surroundings of the test vehicle and the test vehicle itself as well as the whole vehicle test chamber.
c) Conditioning of the test vehicle prior to measurements.
d) Simulation of ambient air conditions (ambient mode).
e) Formaldehyde sampling at elevated temperatures (parking mode).
f) Simulation of driving after the test vehicle has been parked in the sun (driving mode).
1)Tenax TA® is the trade name of a product supplied by Buchem. This information is given for the convenience of users of this document and does not constitute an endorsement by ISO of the product named. Equivalent products may be used if they can be shown to lead to the same results.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    19 pages
    English language
    sale 15% off
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 15% off
SIST
SIST ISO 23431:2021(Main)
Measurement of road tunnel air quality
ISO 23431:2021

This document describes methods for determining air speed and flow direction, CO, NO and NO2 concentrations and visibility in road tunnels using direct-reading instruments. This document specifically excludes requirements relating to instrument conformance testing.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    31 pages
    English language
    sale 15% off
  • Standard
    33 pages
    French language
    sale 15% off
  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 15% off
  • Draft
    33 pages
    French language
    sale 15% off
SIST
SIST ISO 16000-28:2021(Main)
Indoor air - Part 28: Determination of odour emissions from building products using test chambers
ISO 16000-28:2020

This document specifies a laboratory test method using test chambers defined in ISO 16000-9 and further specified in EN 16516 and evaluation procedures for the determination of odours emitted from building products and materials.
Sampling, transport and storage of materials under test, as well as preparation of test specimens are described in ISO 16000-11 and further specified in EN 16516.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    35 pages
    English language
    sale 15% off
  • Standard
    37 pages
    French language
    sale 15% off
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    35 pages
    English language
    sale 15% off
  • Draft
    37 pages
    French language
    sale 15% off
SIST
SIST-TS CEN/TS 17458:2021(Main)
Ambient air - Methodology for the assessment of the performance of source apportionment modelling system applications
CEN/TS 17458:2020

The European Air Quality Directive (Directive on ambient air quality and cleaner air for Europe) identifies different uses for modelling: Assessment, planning, forecast and source apportionment (SA). This CEN/TS addresses source apportionment modelling and specifies performance tests to check whether given criteria for receptor oriented source apportionment (RM) are met. The scope of the tests set out in this CEN/TS is performance assessment of SA of particulate matter using RM in the context of the European Directives 2004/107/EC and 2008/50/EC (AQD) including the Commission Implementing Decision 2011/850/EU of 12 December 2011. The application of RM does not quantify the spatial origin of particulate matter hence this CEN/TS does not test spatial SA.
This CEN/TS addresses RM users: participants and organisers of source apportionment intercomparison studies as well as practitioners of individual source apportionment studies. This CEN/TS is suitable for the evaluation of results of a specific SA modelling system with respect to intercomparison reference values (a-priori known or calculated on the basis of participants' values, see 3.12) in the following application areas:
- Assessment of performance and uncertainties of a modelling system or modelling system set up using the indicators laid down in this CEN/TS.
- Testing and comparing different source apportionment outputs in a specific situation (applying an evaluation dataset) using the indicators laid down in this CEN/TS.
- QA/QC tests every time practitioners run a modelling system.
It should be noted for clarity that the procedures and calculations presented in this CEN/TS cannot be used to check the performance of a specific SA modelling result without having any a-priori reference information about the contributions of sources/source categories.
The principles of receptor oriented models are summarised in Annex A. An overview of uncertainty sources and recommendations about steps to follow in SA studies are provided in Annex B and Annex C.
There are different methodologies than RM widely used to accomplish SA, e.g. source oriented models. These other methodologies cover aspects of SA which are required in the AQD and are not addressed by RM. Performance assessment of such methodologies is out of the scope of this CEN/TS.

  • Technical specification
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 17554:2021(Main)
Ambient air - Application of EN 16909 for the determination of elemental carbon (EC) and organic carbon (OC) in PM10 and PMcoarse
CEN/TR 17554:2020

This document describes procedures to assess the applicability of the standard method EN 16909 (determination of OC and EC deposited on filters) to particle size fractions up to 10 µm in aerodynamic diameter (50 % cut off).

  • Technical report
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day