SIST EN ISO 15015:2026

SLOVENSKI STANDARD
01-januar-2026
Polimerni materiali - Ekstrudirane plošče iz modificiranih akrilonitril-stirenskih
kopolimerov (ABS, AEPDS in ASA), odpornih proti udarcem - Zahteve in
preskusne metode (ISO 15015:2025)
Plastics - Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS,
AEPDS and ASA) - Requirements and test methods (ISO 15015:2025)
Kunststoffe - Extrudierte Tafeln aus schlagzäh-modifizierten Acrylnitril/Styrol-
Copolymeren (ABS, AEPDS und ASA) - Anforderungen und Prüfverfahren (ISO
15015:2025)
Plastiques - Plaques extrudées en copolymères d'acrylonitrile-styrène modifiés choc
(ABS, AEPDS ou ASA) - Exigences et méthodes d'essai (ISO 15015:2025)
Ta slovenski standard je istoveten z: EN ISO 15015:2025
ICS:
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 15015
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2025
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 15015:2011
English Version
Plastics - Extruded sheets of impact-modified acrylonitrile-
styrene copolymers (ABS, AEPDS and ASA) - Requirements
and test methods (ISO 15015:2025)
Plastiques - Plaques extrudées en copolymères Kunststoffe - Extrudierte Tafeln aus schlagzäh-
d'acrylonitrile-styrène modifiés choc (ABS, AEPDS ou modifizierten Acrylnitril/Styrol-Copolymeren (ABS,
ASA) - Exigences et méthodes d'essai (ISO AEPDS und ASA) - Anforderungen und Prüfverfahren
15015:2025) (ISO 15015:2025)
This European Standard was approved by CEN on 22 November 2025.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15015:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 15015:2025) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2026, and conflicting national standards shall be
withdrawn at the latest by May 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15015:2011.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 15015:2025 has been approved by CEN as EN ISO 15015:2025 without any modification.

International
Standard
ISO 15015
Third edition
Plastics — Extruded sheets of impact-
2025-11
modified acrylonitrile-styrene
copolymers (ABS, AEPDS and ASA) —
Requirements and test methods
Plastiques — Plaques extrudées en copolymères d'acrylonitrile-
styrène modifiés choc (ABS, AEPDS ou ASA) — Exigences et
méthodes d'essai
Reference number
ISO 15015:2025(en) © ISO 2025
ISO 15015:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 15015:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Material. 2
5 Requirements . 2
5.1 Appearance .2
5.2 Dimensional tolerances .2
5.2.1 Thickness .2
5.2.2 Length and width . .2
5.2.3 Rectangularity .3
5.2.4 Bow of sheets in rolled form .3
5.3 Properties .3
5.3.1 Mechanical and thermal properties .3
5.3.2 Behaviour on heating .4
5.3.3 Physiological behaviour .4
6 Test methods . 5
6.1 Test specimens.5
6.1.1 Preparation of test specimens .5
6.1.2 Conditioning .5
6.1.3 Test conditions .5
6.2 Delivery condition .5
6.3 Appearance .5
6.4 Dimensions .5
6.4.1 Thickness,h .5
6.4.2 Length, l, and width, b . . .6
6.4.3 Rectangularity .6
6.4.4 Bow of sheets in rolled form .6
6.5 Density .6
6.6 Mechanical properties .6
6.6.1 Tensile stress at yield, σ .6
y
6.6.2 Modulus of elasticity in tension,E .6
t
6.6.3 Charpy impact strength of unnotched specimens,a .6
cu
6.6.4 Charpy impact strength of notched specimens,a .6
cn
6.6.5 Ball indentation hardness .6
6.6.6 Melt mass-flow rate (MFR) . .6
6.7 Thermal properties .7
6.7.1 Vicat softening temperature .7
6.7.2 Determination of shrinkage on heating .7
7 Designation . 8
7.1 Example for ABS sheets .8
7.2 Example for ASA sheets in rolled form .9
8 Marking . . 9
Annex A (informative) Additional guide values . 10
Bibliography .11

iii
ISO 15015:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC
249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
This third edition cancels and replaces the second edition (ISO 15015:2011), which has been technically revised
The main changes are as follows:
— Clause 3, Terms and definitions, has been added, and subsequent clauses have been renumbered;
— Formula (2) has been deleted because the tolerance for the entire sheets delivery would be higher than
for each individual sheet, and subsequent formulae have been renumbered;
— in the title of Table 2, ISO 291 has been added;
— in Tables 2 and 3, the mechanical properties 50 % impact-failure energy, E , at h = 4 mm have been
50 n
deleted as it is not used;
— puncture impace behaviour (former 5.6.5) has been deleted as it is not used.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
International Standard ISO 15015:2025(en)
Plastics — Extruded sheets of impact-modified acrylonitrile-
styrene copolymers (ABS, AEPDS and ASA) — Requirements
and test methods
1 Scope
This document specifies the requirements and test methods for solid flat extruded sheets of impact-modified
acrylonitrile-styrene copolymer materials:
— acrylonitrile-butadiene-styrene (ABS),
— acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) (commonly known as AES), and
— acrylonitrile-styrene-acrylate (ASA), without fillers or reinforcing materials.
...