oSIST prEN 2714-013:2024
(Main)Aerospace series - Cables, electrical, single and multicore for general purpose - Operating temperatures between - 55 °C and 260 °C - Part 013: DR family, screened (spiral) and jacketed, UV laser printable - Product standard
Aerospace series - Cables, electrical, single and multicore for general purpose - Operating temperatures between - 55 °C and 260 °C - Part 013: DR family, screened (spiral) and jacketed, UV laser printable - Product standard
This document specifies the characteristics of UV laser printable DR family, single and multicore screened (spiral) and jacketed electrical lightweight cables for use in the on-board electrical systems of aircraft, at operating temperatures between −55 °C and 260 °C. Nevertheless, if needed, − 65 °C is also acceptable as shown by cold test.
It is also be possible to mark these cables by qualified compatible marking.
These markings satisfy the requirements of EN 3838.
Luft- und Raumfahrt - Leitungen, elektrisch, ein- und mehradrig, für allgemeine Verwendung - Betriebstemperaturen zwischen -55 °C und 260 °C - Teil 013: DR-Familie, geschirmt (Umseilung) und ummantelt, UV-Laser-bedruckbar - Produktnorm
No Scope available
Série aérospatiale - Câbles, électriques, mono et multiconducteurs d'usage général - Températures de fonctionnement comprises entre -55 °C et 260 °C - Partie 013 : Famille DR, blindés (guipés) et gainés, marquables par laser UV - Norme de produit
No Scope available
Aeronavtika - Eno- ali večžilni električni kabli za splošno uporabo - Delovne temperature med –55 °C in 260 °C - 013. del: Družina DR, oklopljeni (spirala) in oplaščeni, z možnostjo UV-laserskega tiskanja - Standard za proizvod
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 2714-013:2024
01-junij-2024
Aeronavtika - Eno- ali večžilni električni kabli za splošno uporabo - Delovne
temperature med –55 °C in 260 °C - 013. del: Družina DR, oklopljeni (spirala) in
oplaščeni, z možnostjo UV-laserskega tiskanja - Standard za proizvod
Aerospace series - Cables, electrical, single and multicore for general purpose -
Operating temperatures between - 55 °C and 260 °C - Part 013: DR family, screened
(spiral) and jacketed, UV laser printable - Product standard
Luft- und Raumfahrt - Leitungen, elektrisch, ein- und mehradrig, für allgemeine
Verwendung - Betriebstemperaturen zwischen -55 °C und 260 °C - Teil 013: DR-Familie,
geschirmt (Umseilung) und ummantelt, UV-Laser-bedruckbar - Produktnorm
Série aérospatiale - Câbles, électriques, mono et multiconducteurs d'usage général -
Températures de fonctionnement comprises entre -55 °C et 260 °C - Partie 013 : Famille
DR, blindés (guipés) et gainés, marquables par laser UV - Norme de produit
Ta slovenski standard je istoveten z: prEN 2714-013
ICS:
29.060.20 Kabli Cables
49.060 Letalska in vesoljska Aerospace electric
električna oprema in sistemi equipment and systems
oSIST prEN 2714-013:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 2714-013:2024
---------------------- Page: 2 ----------------------
oSIST prEN 2714-013:2024
DRAFT
EUROPEAN STANDARD
prEN 2714-013
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2024
ICS 49.060 Will supersede EN 2714-013:2017
English Version
Aerospace series - Cables, electrical, single and multicore
for general purpose - Operating temperatures between -
55 °C and 260 °C - Part 013: DR family, screened (spiral)
and jacketed, UV laser printable - Product standard
Série aérospatiale - Câbles, électriques, mono et Luft- und Raumfahrt - Leitungen, elektrisch, ein- und
multiconducteurs d'usage général - Températures de mehradrig, für allgemeine Verwendung -
fonctionnement comprises entre -55 °C et 260 °C - Betriebstemperaturen zwischen -55 °C und 260 °C -
Partie 013 : Famille DR, blindés (guipés) et gainés, Teil 013: DR-Familie, geschirmt (Umseilung) und
marquables par laser UV - Norme de produit ummantelt, UV-Laser-bedruckbar - Produktnorm
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 2714-013:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 2714-013:2024
prEN 2714-013:2024 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms, definitions, symbols and abbreviations . 4
4 Materials and construction .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.