SIST EN 60695-2-12:2011
Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2010)
Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2010)
This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI). GWFI is the highest temperature, determined during this standardized procedure, at which the tested material
a) does not ignite or, if it does, extinguishes within 30 s after removal of the glow-wire and is
not totally consumed, and
b) molten drips, if they occur, do not ignite the wrapping tissue.
This test method is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire ignition temperature (GWIT) test method for materials, IEC 60695-2-13, can then be used in a preselection process in accordance with IEC 60695-1-30 to judge the ability of materials to meet the requirements of IEC 60695-2-11. NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests may allow a reduction of end product testing. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-12: Prüfverfahren mit dem Glühdraht - Prüfung mit dem Glühdraht zur Entflammbarkeit (GWFI) von Werkstoffen (IEC 60695-2-12:2010)
Essais relatifs aux risques du feu - Partie 2-12: Essais au fil incandescent/chauffant - Méthode d'essai d'indice d'inflammabilité au fil incandescent (GWFI) pour matériaux (CEI 60695-2-12:2010)
La CEI 60695-2-12:2010 spécifie les détails de l'essai au fil incandescent quand il est appliqué à des éprouvettes d'essai de matériaux isolants électriques solides ou autres matériaux solides pour les essais d'inflammabilité dans le but de déterminer l'indice d'inflammabilité au fil incandescent (GWFI, glow-wire flammability index). Le GWFI est la température la plus élevée, déterminée durant cette procédure normalisée, à laquelle le matériau essayé; ne s'enflamme pas ou s'il s'enflamme, s'éteint dans les 30 s qui suivent le retrait du fil incandescent et n'est pas entièrement consumé, et gouttes en fusion, s'il y a lieu, n'enflamme pas le papier mousseline. Cette norme doit être utilisée conjointement avec la CEI 60695-2-10 et la CEI 60695-2-13. Cette deuxième édition inclut les prochains changements techniques significatifs par rapport à l'édition précédente: - modification du titre; - ajout d'une Introduction; - clarification du Domaine d'application; - extension de l'Article 2: Références normatives; - définitions ajoutées à l'Article 3; - révision de l'Article 4 pour alignement avec la série CEI 60695-11 afin d'introduire des lignes directrices concernant les programmes d'essai pour les variations des matériaux; - clarification de l'Article 8: Conditionnement (désormais Article 7); - suppression de l'Article 9 'Mesures initiales'; - extension de l'Article 10: Méthodes d'essai (désormais Article 8); - extension de l'Article 11: Observations et mesures (désormais Article 9); - clarification de l'Article 12: Evaluation des résultats de l'essai (désormais Article 10); - extension de l'Article 13: Rapport d'essai (désormais Article 11). Cette norme a le statut de publication fondamentale de sécurité, conformément au Guide CEI 104 et au Guide ISO/CEI 51.
Preskušanje požarne ogroženosti - 2-12. del: Preskusne metode z žarilno žico - Preskusna metoda za materiale: indeks vnetljivosti z žarilno žico (GWFI) (IEC 60695-2-12:2010)
Ta del IEC 60695 določa podrobnosti preskusa z žarilno žico, ki se uporablja za preskus vzorca trdnih električnih izolacijskih materialov ali trdnih materialov za preskušanje vnetljivosti, da se ugotovi indeks vnetljivosti z žarilno žico (GWFI). GWFI je najvišja temperatura, ugotovljena med tem standardiziranim postopkom, pri kateri se preskušani material:
a) ne vname ali, če se, ugasne v 30 sekundah po umiku žarilne žice ter se
ali ne v celoti porabi in
b) če se pojavi kapljajoča talina, se ovojno blago ne vname.
Ta preskusna metoda je preskus materialov, izveden na seriji standardnih preskusnih vzorcev. Pridobljeni podatki, skupaj s podatki preskusne metode temperature vžiga žarilne žice (GWIT) za materiale, IEC 60695-2-13, se lahko uporabijo v predizbirnem postopku v skladu z IEC 60695-1-30, da se presodi, ali materiali lahko izpolnjujejo zahteve iz IEC 60695-2-11. OPOMBA Kot posledica izvajanja ocene požarne ogroženosti primerno zaporedje predizbirnih preskusov vnetljivosti in vžiga lahko omogoči zmanjševanje preskušanja končnega proizvoda. Ta osnovna varnostna publikacija je namenjena temu, da jo uporabljajo tehnični odbori pri pripravi standardov v skladu z načeli, opredeljenimi v IEC Guide 104 in ISO/IEC Guide 51. Ena od odgovornosti tehničnega odbora je, če je to primerno, uporabiti temeljne varnostne publikacije pri pripravi svojih publikacij. Zahteve, preskusne metode ali preskusni pogoji te temeljne varnostne publikacije se ne uporabljajo, razen če se ustrezne publikacije nanje izrecno sklicujejo ali jih vključujejo.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Preskušanje požarne ogroženosti - 2-12. del: Preskusne metode z žarilno žico - Preskusna metoda za materiale: indeks vnetljivosti z žarilno žico (GWFI) (IEC 60695-2-12:2010)Prüfungen zur Beurteilung der Brandgefahr - Teil 2-12: Prüfverfahren mit dem Glühdraht - Prüfung mit dem Glühdraht zur Entflammbarkeit (GWFI) von Werkstoffen (IEC 60695-2-12:2010)Essais relatifs aux risques du feu - Partie 2-12: Essais au fil incandescent/chauffant - Méthode d'essai d'indice d'inflammabilité au fil incandescent (GWFI) pour matériaux (CEI 60695-2-12:2010)Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2010)13.220.40Sposobnost vžiga in obnašanje materialov in proizvodov pri gorenjuIgnitability and burning behaviour of materials and productsICS:Ta slovenski standard je istoveten z:EN 60695-2-12:2010SIST EN 60695-2-12:2011en01-februar-2011SIST EN 60695-2-12:2011SLOVENSKI
STANDARDSIST EN 60695-2-12:20021DGRPHãþD
EUROPEAN STANDARD EN 60695-2-12 NORME EUROPÉENNE
EUROPÄISCHE NORM December 2010
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2010 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60695-2-12:2010 E
ICS 13.220.40, 29.020 Supersedes EN 60695-2-12:2001
English version
Fire hazard testing -
Part 2-12: Glowing/hot-wire based test methods -
Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2010)
Essais relatifs aux risques du feu -
Partie 2-12: Essais au fil incandescent/chauffant -
Méthode d'essai d'indice d'inflammabilité au fil incandescent (GWFI) pour matériaux(CEI 60695-2-12:2010)
Prüfungen zur Beurteilung der Brandgefahr -
Teil 2-12: Prüfverfahren mit dem Glühdraht -
Prüfung mit dem Glühdraht zur Entflammbarkeit (GWFI) von Werkstoffen (IEC 60695-2-12:2010)
This European Standard was approved by CENELEC on 2010-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
ISO/IEC Guide 51.
This standard is to be used in conjunction with EN 60695-2-10 and EN 60695-2-13.
This EN 60695-2-12:2010 includes the following significant technical changes with respect to
EN 60695-2-12:2001: – modified title; – addition of an Introduction; – clarification of Scope; – expansion of Clause 2: Normative references; – definitions added to Clause 3; – revision of Clause 4 to alignment with the EN 60695-11 series to introduce guidance on test programs for material variations; – clarification of Clause 8: Conditioning (now Clause 7); – deletion of Clause 9 “Initial measurements”; – expansion of Clause 10: Test procedures (now Clause 8); – expansion of Clause 11: Observation and measurement (now Clause 9); – clarification of Clause 12: Evaluation of test results (now Clause 10); – expansion of Clause 13: Test report (now Clause 11). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2011-09-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2013-12-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 60695-2-12:2010 was approved by CENELEC as a European Standard without any modification. SIST EN 60695-2-12:2011
- 3 - EN 60695-2-12:2010 In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60695-1-10 NOTE
Harmonized as EN 60695-1-10. IEC 60695-1-11 IEC 60695-11 series NOTE
Harmonized as EN 60695-1-11.
NOTE
Harmonized in EN 60695-11 series (not modified). __________
(normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60695-1-30 2008 Fire hazard testing -
Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines EN 60695-1-30 2008
IEC 60695-2-10 2000 Fire hazard testing -
Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure EN 60695-2-10 2001
IEC 60695-2-11
Fire hazard testing -
Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products EN 60695-2-11 2001
IEC 60695-2-13 - Fire hazard testing -
Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials EN 60695-2-13 -
ISO/IEC Guide 51 1999 Safety aspects - Guidelines for their inclusion in standards - -
IEC Guide 104 1997 The preparation of safety publications and the use of basic safety publications and group safety publications - -
ISO 291 2008 Plastics - Standard atmospheres for conditioning and testing
EN ISO 291 2008
ISO 293 2004 Plastics - Compression moulding of test specimens of thermoplastic materials EN ISO 293 2005
ISO 294 Series Plastics - Injection moulding of test
specimens of thermoplastic materials -
Part 1: General principles, and moulding of multipurpose and bar test specimens EN ISO 294 Series
ISO 295 2004 Plastics - Compression moulding of test specimens of thermosetting materials
EN ISO 295 2004
ISO 13943 2008 Fire safety - Vocabulary EN ISO 13943 2010
IEC 60695-2-12Edition 2.0 2010-10INTERNATIONAL STANDARD NORME INTERNATIONALEFire hazard testing –
Part 2-12: Glowing/hot-wire based test methods – Glow-wire flammability index (GWFI) test method for materials
Essais relatifs aux risques du feu –
Partie 2-12: Essais au fil incandescent/chauffant – Méthode d'essai d'indice d’inflammabilité au fil incandescent (GWFI) pour matériaux
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE MICS 13.220.40; 29.020 PRICE CODECODE PRIXISBN 978-2-88912-215-8BASIC SAFETY PUBLICATION PUBLICATION FONDAMENTALE DE SÉCURITÉ® Registered trademark of the International Electrotechnical Commission
– 2 – 60695-2-12 © IEC:2010
CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references.6 3 Terms and definitions.7 4 Test specimens.8 4.1 Test specimen preparation.8 4.2 Test specimen dimensions.8 4.3 Testing ranges in formulations.8 4.3.1 General.8 4.3.2 Density, melt flows and filler/reinforcement.9 4.3.3 Colour.9 5 Apparatus.9 6 Temperature measuring system verification.9 7 Conditioning and test conditions.9 7.1 Conditioning of test specimens.9 7.2 Conditioning of the wrapping tissue and the wooden board.9 7.3 Testing conditions.9 8 Test procedure.10 8.1 General.10 8.2 Initial test temperatures.10 8.3 Test temperatures.10 9 Observations and measurements.11 9.1 General.11 9.2 Initial observations.11 9.3 Test observations.11 10 Evaluation of test results.11 10.1 Test criteria.11 10.2 Glow-wire flammability index.11 11 Test report.12 Bibliography.13
Table 1 – Initial test temperatures.10
60695-2-12 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
FIRE HAZARD TESTING –
Part 2-12: Glowing/hot-wire based test methods –
Glow-wire flammability index (GWFI) test method for materials
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No l
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.