iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60695-2-12:2011/A1:2015

(Amendment)

Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2010/A1:2014)

Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2010/A1:2014)

This part of IEC 60695 describes a glow-wire flammability index test for materials. It should be
used to measure, describe, and rank the properties of materials in response to heat caused
by contact with an electrically heated wire under controlled laboratory conditions. This may be
useful for the evaluation of materials for use in products that may be exposed to excess
thermal stress such as a fault current flowing through a wire, overloading of components,
and/or bad connections. It should not be used to solely describe or appraise the fire hazard or
fire risk of materials, products, or assemblies under actual fire conditions. However, results of
this test may be used as elements of a fire hazard assessment which takes into account all of
the factors which are pertinent to a particular end use.

Prüfungen zur Beurteilung der Brandgefahr - Teil 2-12: Prüfverfahren mit dem Glühdraht - Prüfung mit dem Glühdraht zur Entflammbarkeit (GWFI) von Werkstoffen

Essais relatifs aux risques du feu - Partie 2-12: Essais au fil incandescent/chauffant - Méthode d'essai d'indice d'inflammabilité au fil incandescent (GWFI) pour matériaux

IEC 60695-2-12:2014 Amendement 1

Preskušanje požarne ogroženosti - 2-12. del: Preskusne metode z žarilno žico - Preskusna metoda za materiale: indeks vnetljivosti z žarilno žico (GWFI) (IEC 60695-2-12:2010/A1:2014)

Ta del standarda IEC 60695 opisuje preskus za materiale, da se ugotovi indeks vnetljivosti z žarilno žico. Uporabljati ga je treba za
merjenje, opisovanje in rangiranje lastnosti materialov kot odziv na vročino, ki nastane pri stiku z električno segreto žico, pod nadzorovanimi laboratorijskimi pogoji. Uporablja se lahko za oceno materialov za uporabo v izdelkih, ki so lahko izpostavljeni čezmernemu termičnemu vplivu, kot je okvarni tok, ki teče skozi žico, preobremenitev komponent in/ali slabe povezave. Uporabljal naj se ne bi samo za opis ali oceno nevarnosti ali tveganja vžiga materialov, izdelkov ali sestavov pod dejanskimi pogoji požara. Vendar je mogoče rezultate tega preskusa uporabiti kot elemente ocene nevarnosti vžiga, ki upošteva vse dejavnike, ki se nanašajo na posamezno končno uporabo.

General Information

Status
Withdrawn
Publication Date
22-Feb-2015
Withdrawal Date
19-Nov-2024
ICS
13.220.40 - Ignitability and burning behaviour of materials and products
Technical Committee
I09 - Imaginarni 09
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-Nov-2024
Due Date
13-Dec-2024
Completion Date
20-Nov-2024
Ref Project
EN 60695-2-12:2010/A1:2014 - Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials

Relations

Replaced By
SIST EN IEC 60695-2-12:2022 - Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2021)
Effective Date
23-Nov-2021
Amends
SIST EN 60695-2-12:2011 - Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2010)
Effective Date
16-Oct-2012

Buy Standard

EN 60695-2-12:2011/A1:2015EN 60695-2-12:2011/A1:2015
PreviousNext
Amendment
EN 60695-2-12:2011/A1:2015
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2015
Preskušanje požarne ogroženosti - 2-12. del: Preskusne metode z žarilno žico -
Preskusna metoda za materiale: indeks vnetljivosti z žarilno žico (GWFI) (IEC
60695-2-12:2010/A1:2014)
Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire
flammability index (GWFI) test method for materials (IEC 60695-2-12:2010/A1:2014)
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-12: Prüfverfahren mit dem Glühdraht
- Prüfung mit dem Glühdraht zur Entflammbarkeit (GWFI) von Werkstoffen
Essais relatifs aux risques du feu - Partie 2-12: Essais au fil incandescent/chauffant -
Méthode d'essai d'indice d'inflammabilité au fil incandescent (GWFI) pour matériaux
Ta slovenski standard je istoveten z: EN 60695-2-12:2010/A1:2014
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60695-2-12:2010/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 13.220.40; 29.020
English Version
Fire hazard testing - Part 2-12: Glowing/hot-wire based test
methods - Glow-wire flammability index (GWFI) test method for
materials
(IEC 60695-2-12:2010/A1:2014)
Essais relatifs aux risques du feu - Partie 2-12: Essais au fil Prüfungen zur Beurteilung der Brandgefahr - Teil 2-12:
incandescent/chauffant - Méthode d'essai d'indice Prüfverfahren mit dem Glühdraht - Prüfung mit dem
d'inflammabilité au fil incandescent (GWFI) pour matériaux Glühdraht zur Entflammbarkeit (GWFI) von Werkstoffen
(CEI 60695-2-12:2010/A1:2014) (IEC 60695-2-12:2010/A1:2014)
This amendment A1 modifies the European Standard EN 60695-2-12:2010; it was approved by CENELEC on 2014-03-19. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60695-2-12:2010/A1:2014 E

EN 60695-2-12:2010 /A1:2014 - 2 -
Foreword
The text of document 89/1198/FDIS, future IEC 60695-2-12:2010/A1, prepared by IEC TC 89, Fire hazard
testing, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60695-
2-12:2010/A1:2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented (dop) DAV + 6 months
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2017-03-19
with the EN have to be withdrawn

Endorsement notice
The text of the International Standard IEC 60695-2-12:2010/A1:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60695-2-11 NOTE  Harmonized as EN 60695-2-11.
ISO/IEC 13943:2008 NOTE  Harmonized as EN ISO 13943:2010.

- 3 - EN 60695-2-12:2010/A1:2014

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
Publication Year Title EN/HD Year
In Annex ZA of EN 60695-2-12:2010, remove the dates from the following existing references:
IEC Guide 104 -  The preparation of safety publications and - -
the use of basic safety publications and
group safety publications
ISO 293 -  Plastics - Compression moulding of test EN ISO 293 -
specimens of thermoplastic materials
ISO 295 -  Plastics_- Compression moulding of test EN ISO 295 -
specimens of thermosetting materials
ISO/IEC Guide 51 -  Safety aspects - Guidelines for their - -
inclusion in standards
In Annex ZA of EN 60695-2-12:2010, remove the following references:
IEC 60695-2-11 2000 Fire hazard testing - EN 60695-2-11 2001
Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test
method for end-products
ISO 13943 2008 Fire safety - Vocabulary EN ISO 13943 2010

IEC 60695-2-12 ®
Edition 2.0 2014-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
BA SIC SAFETY PUBLICATION
PU BLICATION FONDAMENTALE DE
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60695-2-10:2022/AC:2024(Corrigendum)
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure (IEC 60695-2-10:2021/COR1:2024)
EN IEC 60695-2-10:2021/AC:2024-01
  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-2-11:2022(Main)
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end products (GWEPT) (IEC 60695-2-11:2021)
EN IEC 60695-2-11:2021

This part of IEC 60695 specifies a test method on an end product. It is intended to simulate the
effects of thermal stresses produced by an electrically heated source to represent a fire hazard.
This test method is used to check that, under defined test conditions, an end product exposed
to an electrically heated source has either a limited ability to ignite or, if it ignites, a limited
ability to propagate flame. However, the fire hazard analysis, the flammability aspects and the
flame spreading to other products are not covered by this document.
This basic safety publication focusing on safety test method(s) is primarily intended for use by
technical committees in the preparation of safety publications in accordance with the principles
laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-7-2:2022(Main)
Fire hazard testing - Part 7-2: Toxicity of fire effluent - Summary and relevance of test methods (IEC 60695-7-2:2021)
EN IEC 60695-7-2:2021

This part of IEC 60695-7 gives a brief summary of the test methods that are in common use in
the assessment of the toxicity of fire effluent. It includes special observations on their relevance
to real fire scenarios and gives recommendations on their use.
It advises which tests provide toxic potency data that are relevant to real fire scenarios, and
which are suitable for use in fire hazard assessment and fire safety engineering.
The list of test methods is not to be considered exhaustive.
This summary cannot be used in place of published standards which are the only valid reference
documents.
This basic safety publication is intended for use by technical committees in the preparation of
standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications. The requirements, test methods
or test conditions of this basic safety publication will not apply unless specifically referred to or
included in the relevant publications.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-2-10:2022(Main)
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure (IEC 60695-2-10:2021)
EN IEC 60695-2-10:2021

This part of IEC 60695 specifies the glow-wire apparatus and common test procedure to
simulate the effects of thermal stresses which may be produced by heat sources such as
glowing elements or overloaded resistors, for short periods, in order to assess the fire hazard
by a simulation technique.
The test procedure described in this document is a common test procedure intended for the
small-scale tests in which a standardized electrically heated wire is used as a source of ignition.
It is a common part of the test procedures applied to end products and to solid electrical
insulating materials or other solid combustible materials.
A detailed description of each particular test procedure is given in IEC 60695-2-11,
IEC 60695-2-12 and IEC 60695-2-13.
This basic safety publication focusing on safety test method(s) is primarily intended for use by
technical committees in the preparation of safety publications in accordance with the principles
laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-5-1:2022(Main)
Fire hazard testing - Part 5-1: Corrosion damage effects of fire effluent - General guidance (IEC 60695-5-1:2021)
EN IEC 60695-5-1:2021

This part of IEC 60695 provides guidance on the following:
a) general aspects of corrosion damage test methods;
b) methods of measurement of corrosion damage;
c) consideration of test methods;
d) relevance of corrosion damage data to hazard assessment.
This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies.
One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-2-12:2022(Main)
Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials (IEC 60695-2-12:2021)
EN IEC 60695-2-12:2021

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test
specimens of solid electrical insulating materials or other solid materials for flammability
testing to determine the glow-wire flammability index (GWFI).
GWFI is the highest temperature, determined during this standardized procedure, at which the
tested material does not ignite or, if it does, extinguishes within 30 s after removal of the
glow-wire and is not totally consumed; and molten drips, if they occur, do not ignite the
wrapping tissue.
This test method is a materials test carried out on a series of standard test specimens. The
data obtained, along with data from the glow-wire ignition temperature (GWIT) test method for
materials, IEC 60695-2-13, can then be used in a preselection process in accordance with
IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of
IEC 60695-2-11.
NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability
and ignition tests can allow a reduction of end product testing.
This basic safety publication focusing on safety test method(s) is primarily intended for use by
technical committees in the preparation of safety publications in accordance with the
principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-9-2:2021(Main)
Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods (IEC 60695-9-2:2021)
EN IEC 60695-9-2:2021

This part of IEC 60695-9 presents a summary of published test methods that are used to determine the surface spread of flame of electrotechnical products or materials from which they are formed. It represents the current state of the art of the test methods and, where available, includes special observations on their relevance and use. The list of test methods is not to be considered exhaustive, and test methods that were not developed by the IEC are not to be considered as endorsed by the IEC unless this is specifically stated. This summary cannot be used in place of published standards which are the only valid reference documents. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-2-13:2021(Main)
Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials (IEC 60695-2-13:2021)
EN IEC 60695-2-13:2021

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test
specimens of solid electrical insulating materials or other solid materials for ignitability testing
to determine the glow-wire ignition temperature (GWIT).
The GWIT is the temperature which is 25 K (or 30 K) higher than the maximum test
temperature, determined during this standardized procedure, at which the tested material
does not ignite, or sustained flaming combustion does not occur for a time longer than 5 s for
any single flame event and the specimen is not totally consumed.
This test is a materials test carried out on a series of standard test specimens. The data
obtained, along with data from the glow-wire flammability index (GWFI) test method for
materials, IEC 60695-2-12, can then be used in a preselection process in accordance with
IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of
IEC 60695-2-11.
NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability
and ignition tests can allow a reduction of end product testing.
This basic safety publication focusing on safety test method(s) is primarily intended for use by
technical committees in the preparation of safety publications in accordance with the
principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-6-1:2021(Main)
Fire hazard testing - Part 6-1: Smoke obscuration - General guidance (IEC 60695-6-1:2021)
EN IEC 60695-6-1:2021

This part of IEC 60695 gives guidance on:
a) the optical measurement of obscuration of smoke;
b) general aspects of optical smoke test methods;
c) consideration of test methods;
d) expression of smoke test data;
e) the relevance of optical smoke data to hazard assessment.
This basic safety publication focusing on safety guidance is primarily intended for use by
technical committees in the preparation of safety publications in accordance with the
principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60695-4:2021(Main)
Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical products (IEC 60695-4:2021)
EN IEC 60695-4:2021

The terms and definitions in this part of IEC 60695 are applicable to fire tests for
electrotechnical products.
This basic safety publication focusing on safety guidance is primarily intended for use by
technical committees in the preparation of safety publications in accordance with the
principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications. The requirements, test
methods or test conditions of this basic safety publication will not apply unless specifically
referred to or included in the relevant publications.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day