SIST EN ISO 9185:2007

SLOVENSKI STANDARD
SIST EN ISO 9185:2007
01-oktober-2007
1DGRPHãþD
SIST EN 373:1996
Varovalna obleka - Ocenitev odpornosti materialov proti obrizgu staljene kovine
(ISO 9185:2007)
Protective clothing - Assessment of resistance of materials to molten metal splash (ISO
9185:2007)
Schutzkleidung - Beurteilung des Materialwiderstandes gegen flüssige Metallspritzer
(ISO 9185:2007)
Vetements de protection - Evaluation de la résistance des matériaux aux projections de
métal fondu (ISO 9185:2007)
Ta slovenski standard je istoveten z: EN ISO 9185:2007
ICS:
13.340.10 Varovalna obleka Protective clothing
SIST EN ISO 9185:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 9185
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2007
ICS 13.340.10 Supersedes EN 373:1993
English Version
Protective clothing - Assessment of resistance of materials to
molten metal splash (ISO 9185:2007)
Vêtements de protection - Évaluation de la résistance des Schutzkleidung - Beurteilung des Materialwiderstandes
matériaux aux projections de métal fondu (ISO 9185:2007) gegen flüssige Metallspritzer (ISO 9185:2007)
This European Standard was approved by CEN on 24 June 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9185:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 9185:2007 (E)







Foreword


This document (EN ISO 9185:2007) has been prepared by Technical Committee CEN/TC 162
"Protective clothing including hand and arm protection and lifejackets", the secretariat of which is
held by DIN, in collaboration with Technical Committee ISO/TC 94 "Personal safety - Protective
clothing and equipment".

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2008, and conflicting national
standards shall be withdrawn at the latest by January 2008.

This document supersedes EN 373:1993.

This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU
Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
2

---------------------- Page: 3 ----------------------

EN ISO 9185:2007 (E)


Annex ZA

(informative)

Relationship between this International Standard and the Essential
Requirements of EU Directive 89/686/EEC



This International Standard has been prepared under a mandate given to CEN/CENELEC by the
European Commission and the European Free Trade Association to provide a means of
conforming to Essential Requirements of the New Approach Directive 89/686/EEC Personal
Protective Equipment.

Once this standard is cited in the Official Journal of the European Communities under that
Directive and has been implemented as a national standard in at least one Member State,
compliance with the clauses of this standard, together with the requirements given in the specific
product standard, confers, within the limits of the scopes of both standards, a presumption of
conformity with the corresponding Essential Requirements of Directive 89/686/EEC, Annex II,
clause 3.6.

WARNING: Other requirements and other EU Directives may be applicable to the products
falling within the scope of this standard.



3

---------------------- Page: 4 ----------------------

INTERNATIONAL ISO
STANDARD 9185
Second edition
2007-07-01

Protective clothing — Assessment of
resistance of materials to molten metal
splash
Vêtements de protection — Évaluation de la résistance des matériaux
aux projections de métal fondu




Reference number
ISO 9185:2007(E)
©
ISO 2007

---------------------- Page: 5 ----------------------

ISO 9185:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 6 ----------------------

ISO 9185:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle. 1
5 Apparatus and materials. 2
6 Conditioning. 6
7 Preparation of test specimens . 6
8 Operator safety . 6
9 Procedure . 7
9.1 Setting up the apparatus. 7
9.2 Preparation of molten metal or cryolite. 7
9.3 Attachment of test material to pin frame. 7
9.4 Pouring . 7
9.5 Examination. 7
9.6 Determination of mass of metal poured. 8
10 Iterative testing . 8
11 Void tests. 8
12 Test report . 8
Annex A (normative) Test conditions for certain metals and for cryolite . 9
Annex B (normative) Method of test for assessment of thermal characteristics of PVC sensor film. 11
Bibliography . 12

© ISO 2007 – All rights reserved iii

---------------------- Page: 7 ----------------------

ISO 9185:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9185 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 162, Protective clothing including hand and arm protection and lifejackets, in collaboration with
Technical Committee ISO/TC 94, Personal safety — Protective clothing and equipment, Subcommittee SC 13,
Protective clothing, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 9185:1990), which has been technically revised.
This second edition includes the following significant technical changes compared to the first edition:
a) new PVC sensor film included;
b) Cryolite included as test metal.
iv © ISO 2007 – All rights reserved

---------------------- Page: 8 ----------------------

ISO 9185:2007(E)
Introduction
ISO 9185:1990 and EN 373:1995 have been used up until now with reasonable success as the principle test
methods for materials used in the manufacture of clothing to protect against large splashes of molten metals.
EN and ISO specifications cite these test methods and set levels of performance in terms of the mass of iron
or aluminium that can be splashed onto test materials without producing damage to the heat sensor film.
The revision of the test methods contained within this International Standard incorporates changes based on
experience that are intended to improve reproducibility and to respond to incident data from the aluminium
smelter industry. A test procedure is therefore introduced to determine the protection provided by materials
when splashed with molten cryolite. This revision also harmonises into one test procedure the previously
slightly different procedures in ISO 9185 and EN 373 for testing with molten aluminium.
A new supply of PVC sensor film has been established together with a new world-wide distributor – see note
in the text. One single specification for PVC film replaces the previously different ones in ISO 9185 and
EN 373.
The test method in this International Standard is distinct from that in ISO 9150, which assesses the protective
performance of materials intended to be manufactured into protective clothing for welding activities.

© ISO 2007 – All rights reserved v

---------------------- Page: 9 ----------------------

INTERNATIONAL STANDARD ISO 9185:2007(E)

Protective clothing — Assessment of resistance of materials to
molten metal splash
1 Scope
This International Standard specifies a method for assessing the heat penetration resistance of materials
intended for use in clothing to protect against large splashes of molten metal. It provides specific procedures
for assessing the effects of splashes of molten aluminium, molten cryolite, molten copper, molten iron and
molten mild steel.
The principle of the test method is applicable to a wider range of hot molten materials than those for which
specific procedures are set out, provided that appropriate measures are applied to protect the test operator. It
is important to note that good resistance of a material to a pure molten metal does not guarantee a good
performance against any slag that can be present in a manufacturing process.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 683-1:1987, Heat-treatable steels, alloy steels and free-cutting steels — Part 1: Direct-hardening
unalloyed and low-alloyed wrought steel in form of different black products
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
damage
〈PVC sensor film〉 any smoothing or modification to the embossing or pinholing of the PVC sensor film,
extending in total for at least 5 mm across its width
NOTE Where the visual change in appearance is in discrete spots, damage occurs when the summation of the width
of each spot exceeds 5 mm across any horizontal section. For cryolite, experience indicates that damage can be defined
as less than 5 mm in width, but greater than 10 mm in length.
3.2
molten metal splash index
figure equal to the minimum mass of molten metal poured which just causes damage to the PVC sensor film
4 Principle
Materials are tested by pouring quantities of molten metal onto the test specimen supported at an angle to the
horizontal on a pin frame. Damage is assessed by placing an embossed thermoplastic PVC sensor film
directly behind, and in contact with, the test specimen and noting changes to the film after pouring. Any
adherence of the metal to the test specimen surface is also noted. Depending on the result, the test is
repeated, using a greater or smaller mass of metal, until the minimum quantity to cause damage to the film is
observed.
© ISO 2007 – All rights reserved 1

---------------------- Page: 10 ----------------------

ISO 9185:2007(E)
5 Apparatus and materials
5.1 Metals and cryolite complying with the specifications set out in Annex A. Other metals or substrates
appropriate to the end use.
NOTE It is advisable that coarse filings or small pieces cut from solid bar or sheet be used, because fine filings have
proved difficult to melt. A range of pouring temperatures used in industry for different metals and for cryolite is given in
Annex A.
1) 2
5.2 PVC sensor film , comprising an embossed PVC sheet, of mass per unit area (300 ± 30) g/m , which
when tested as described in Annex B shows no smoothing or modification of the embossing of the central
area at a block temperature of (166 ± 2) °C but which shows smoothing or modification of the central area at a
block temperature of (183 ± 2) °C. The procedure set out in Annex B shall be undertaken no more than
30 days before any one day of testing in accordance with this International Standard.
NOTE The reason for this continuous calibration of the PVC sensor film is that it is likely to change over time
because of plasticizer loss. It is advisable that the PVC sensor film be stored in a cool and dark location so as to minimize
such changes. Because of the economics and consistency of production, one batch of at least 1500 m is produced and
then used by test laboratories over a period of several years.
5.3 Crucible, whose approximate external dimensions are a height of 97 mm, a top diameter of 80 mm, a
bottom diameter of 56 mm and a capacity (brim full) of 190 ml (see Figure 1).
NOTE For most molten metals, including iron, a graphite impregnated material (if an induction furnace is used) has
been found suitable for the crucible.
5.4 Detachable crucible holder, to
...