SIST EN 60034-19:2015

SLOVENSKI STANDARD
01-april-2015
(OHNWULþQLURWDFLMVNLVWURMLGHO3RVHEQHPHWRGH]DSUHVNXãDQMHHQRVPHUQLK
VWURMHYVNRQYHQFLRQDOQLPHQRVPHUQLPLQXVPHUMHQLPQDSDMDQMHP,(&

Rotating electrical machines - Part 19: Specific test methods for d.c. machines on
conventional and rectifier-fed supplies (IEC 60034-19:2014)
Drehende elektrische Maschinen - Teil 19: Besondere Prüfverfahren für
Gleichstrommaschinen, betrieben an gleichrichtergespeisten Leistungsversorgungen
oder anderen Gleichstromquellen (IEC 60034-19:2014)
Machines électriques tournantes - Partie 19: Méthodes spécifiques d'essai pour
machines à courant continu à alimentation conventionnelle ou redressée (IEC 60034-
19:2014)
Ta slovenski standard je istoveten z: EN 60034-19:2014
ICS:
29.160.01 Rotacijski stroji na splošno Rotating machinery in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60034-19

NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2014
ICS 29.160
English Version
Rotating electrical machines - Part 19: Specific test methods for
d.c. machines on conventional and rectifier-fed supplies
(IEC 60034-19:2014)
Machines électriques tournantes - Partie 19: Méthodes Drehende elektrische Maschinen - Teil 19: Besondere
spécifiques d'essai pour machines à courant continu à Prüfverfahren für Gleichstrommaschinen, betrieben an
alimentation conventionnelle ou redressée gleichrichtergespeisten Leistungsversorgungen oder
(CEI 60034-19:2014) anderen Gleichstromquellen
(IEC 60034-19:2014)
This European Standard was approved by CENELEC on 2014-10-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60034-19:2014 E
Foreword
The text of document 2/1756/FDIS, future edition 2 of IEC 60034-19, prepared by IEC/TC 2 "Rotating
machinery" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2015-07-30
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2017-10-30
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60034-19:2014 was approved by CENELEC as a European
Standard without any modification.

- 3 - EN 60034-19:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60034-1 -  Rotating electrical machines - EN 60034-1 -
Part 1: Rating and performance
IEC 60034-2-1 -  Rotating electrical machines - EN 60034-2-1 -
Part 2-1: Standard methods for determining
losses and efficiency from tests (excluding
machines for traction vehicles)

IEC 60034-19 ®
Edition 2.0 2014-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Rotating electrical machines –

Part 19: Specific test methods for d.c. machines on conventional and

rectifier-fed supplies
Machines électriques tournantes –

Partie 19: Méthodes spécifiques d'essai pour machines à courant continu à

alimentation conventionnelle ou redressée

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX S
ICS 29.160 ISBN 978-2-8322-1861-7

– 2 – IEC 60034-19:2014 © IEC 2014
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and subscripts . 6
3.1 Terms and definitions . 6
3.2 Symbols . 7
3.3 Subscripts . 7
4 Determination of current and voltage specific quantities (rectifier-fed) . 7
4.1 General . 7
4.2 Current ripple . 7
4.3 Voltage ripple. 8
4.4 Measurement of average values . 8
4.5 Measurement of root-mean-square values . 8
4.6 Calculation of current and voltage ripple factors and form factor . 8
5 Determination of the armature circuit inductance . 8
5.1 Procedure performed before starting the tests . 8
5.2 Measurement of armature circuit inductance of shunt and compound-wound
machines . 8
5.3 Measurement of armature circuit inductance of series-excited machine . 9
5.4 Calculation of armature circuit inductance L on the basis of direct
a
measurement . 9
5.5 Saturated armature circuit inductance at a loaded condition . 9
6 Determination of shunt-field inductance . 10
6.1 General . 10
6.2 Unsaturated shunt-field inductance . 10
6.3 Saturated shunt-field inductance . 10
6.4 Shunt-field inductance with consideration of eddy current effect . 10
6.5 Shunt-field inductance without consideration of eddy current effect . 11
7 Determination of black-band zone. 12
7.1 General . 12
7.2 Set-up . 12
7.3 Test procedure . 13
7.3.1 Operating conditions . 13
7.3.2 Determination of the minimum current of the commutating winding . 14
7.3.3 Determination of the maximum current of the commutating winding . 14
7.4 Calculation of black-band width (∆ ) and black-band shift (δ ) . 14
n n
8 Determination of the maximum permissible rate of change of armature current . 15
8.1 General . 15
8.2 Set-up . 15
8.3 Test procedure . 16
8.3.1 Operating conditions . 16
8.3.2 Measuring the rise of armature current . 16
8.4 Calculation of initial rate of change of armature current . 16
9 Additional losses and efficiency of rectifier-fed d.c. motors . 17
9.1 General . 17
9.2 Measurement procedure . 17

IEC 60034-19:2014 © IEC 2014 – 3 –
9.3 Calculation of efficiency . 18
10 Determination of speed regulation . 18
10.1 General . 18
10.2 Operating conditions . 18
10.3 Test procedure . 18
10.4 Determination of speed regulation . 18
11 Determination of the shunt regulation curve . 18
11.1 General . 18
11.2 Operating conditions . 19
11.3 Test procedure . 19
11.4 Determination of the shunt regulation curve . 19
12 Determination of the magnetisation curve . 19
12.1 General . 19
12.2 Operating conditions . 19
12.3 Test procedure . 19
12.3.1 General . 19
12.3.2 Test at no-load . 19
12.3.3 Test at rated load . 20
12.4 Determination of the magnetisation curve . 20

Figure 1 – Determination of saturated armature circuit inductance . 9
Figure 2 – Test circuit for saturated shunt field inductance measurement . 10
Figure 3 – Determination of the field inductance . 11
Figure 4 – Test circuit for black-band testing . 12
Figure 5 – Additional generator used to boost or subtract the armature current . 13
Figure 6 – Black-band zone for a specified constant speed of rotation . 14
Figure 7 – Test circuit for rate of change of armature current measurement . 15
Figure 8 – Transient build-up of armature current . 16
Figure 9 – Test circuit for measurement of ripple losses . 17

– 4 – IEC 60034-19:2014 © IEC 2014
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINES –

Part 19: Specific test methods for d.c. machines
on conventional and rectifier-fed supplies

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60034-19 has been prepared by IEC technical committee 2:
Rotating machinery.
This second edition cancels and replaces the first edition published in 1995. It constitutes a
technical revision. The main technical changes with regard to the previous edition are as
follows:
a) The description of the procedure for black band testing has been detailed and clarified.
b) Procedures for measurement of the magnetization curves under no-load and load
conditions have been added.
IEC 60034-19:2014 © IEC 2014 – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
2/1756/FDIS 2/1764/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
NOTE A table of cross-references of all IEC TC 2 publications can be found on the IEC TC 2 dashboard on the
IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
– 6 – IEC 60034-19:2014 © IEC 2014
ROTATING ELECTRICAL MACHINES –

Part 19: Specific test methods for d.c. machines
on conventional and rectifier-fed supplies

1 Scope
This part of IEC 60034 applies to d.c. machines rated 1 kW and above operating on rectifier-
fed power supplies, d.c. buses or other d.c. sources.
Standardized methods are provided for determining characteristic quantities for conventional
and rectifier-fed d.c. machines.
Excluded are d.c machines for specific applications.
These methods supplement the requirements in IEC 60034-1 and IEC 60034-2-1.
NOTE It is not intended that this standard should be interpreted as requiring the carrying out of any or all of the
tests described therein on any given machine.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60034-1, Rotating electrical machines – Part 1: Rating and performance
IEC 60034-2-1, Rotating electrical machines – Part 2-1: Standard methods for determining
losses and efficiency from tests (excluding machines for traction vehicles)
3 Terms, definitions, symbols and subscripts
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
current ripple
peak-to-peak amplitude of the armature current of rectifier-fed d.c. machines
3.1.2
voltage ripple
peak-to-peak amplitude of the terminal voltage of rectifier-fed d.c. machines
3.1.3
time constant
time to achieve 63,2 % of steady-state value after applying a d.c. step input, assuming a first
order system
IEC 60034-19:2014 © IEC 2014 – 7 –
3.1.4
black band zone
interval between the current limits of the commutating poles, between which sparkless
commutation is attainable for load currents up to and including rated current
3.1.5
sparkless
absence of any type of sparking
3.2 Symbols
C is the capacitance, [F]
f is the frequency, [Hz]
I, i is the current, [A]
L is the inductance, [H]
–1
n is the speed, [min ]
P is the power, [W]
R is the winding resistance, [Ω]
t is the time, [s]
U is the voltage, [V]
Δ is the black band width, [%]
n
δ is the black band shift, [%]
n
𝜏 is the time constant, [s]
θ is the phase angle
3.3 Subscripts
1 input
2 output
a armature
b boost
e exciter
f field
LL additional loss
n test point
N rated condition
s subtract
0 no-load
∞ ultimate
4 Determination of current and voltage specific quantities (rectifier-fed)
4.1 General
This test serves to determine the variation of the terminal voltage and armature current for
rectifier-fed d.c. machines at rated conditions.
4.2 Current ripple
The armature current ripple is best measured with an oscilloscope incorporating capability for
reading both d.c. and a.c. values. An alternative method is to use a peak-to-peak reading

– 8 – IEC 60034-19:2014 © IEC 2014
voltmeter, reading the voltage drop across a non-inductive resistor in series with the armature
circuit.
4.3 Voltage ripple
The voltage ripple may be measured using an oscilloscope, a suitable oscillograph or an
electronic
...