SIST EN 300 220-2 V2.4.1:2012

Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)

Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment to be used in the 25 MHz to 1 000 MHz
frequency range with power levels ranging up to 500 mW;
Part 2: Harmonized EN covering essential requirements
under article 3.2 of the R&TTE Directive

2 Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)

Reference
REN/ERM-TG28-435
Keywords
radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2012.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Transmitter requirements . 8
4.2.1.1 Frequency error and frequency drift . 8
4.2.1.2 Average power (conducted) . 8
4.2.1.3 Effective radiated power . 9
4.2.1.4 Types of spread spectrum modulation. 9
4.2.1.4.1 Frequency Hopping Spread Spectrum devices (FHSS) . 9
4.2.1.4.2 Direct sequence or other spread spectrum than FHSS . 9
4.2.1.5 Transient Power . 9
4.2.1.6 Adjacent channel power . 9
4.2.1.7 Modulation bandwidth . 9
4.2.1.8 Unwanted emissions in the spurious domain . 9
4.2.1.9 Frequency stability under low-voltage conditions . 9
4.2.1.10 Duty cycle . 10
4.2.1.11 Listen Before Talk (LBT) . 10
4.2.1.11.1 Minimum transmitter off-time . 10
4.2.1.11.2 Minimum listening time . 10
4.2.1.11.3 Maximum dead time . 10
4.2.1.11.4 Maximum transmitter on-time . 10
4.2.1.11.5 Time-out-timer . 10
4.3 Receiver requirements . 11
4.3.1 Receiver categories . 11
4.3.2 Receiver sensitivity . 11
4.3.3 Receiver LBT threshold . 11
4.3.4 Adjacent channel selectivity . 11
4.3.5 Blocking . 11
4.3.6 Spurious response rejection . 11
4.3.7 Spurious radiations . 12
5 Testing for compliance with technical requirements . 12
5.1 Description testing for compliance with technical requirements . 12
5.1.1 Environmental conditions for testing . 12
5.1.1.1 Normal and extreme test-conditions. 12
5.1.1.2 Test power source . 12
5.1.2 Choice of samples for test suites . 12
5.1.3 Transmitter test suites . 12
5.1.3.1 Frequency error and drift . 12
5.1.3.2 Average power (conducted) . 12
5.1.3.3 Effective radiated power . 13
5.1.3.4 Transient power . 13
5.1.3.5 Adjacent channel power . 13
ETSI
4 Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)
5.1.3.6 Modulation bandwidth . 13
5.1.3.7 Unwanted emissions in the spurious domain . 13
5.1.3.8 Frequency stability under low-voltage conditions . 13
5.1.4 Receiver test suites. 13
5.1.4.1 Receiver sensitivity . 13
5.1.4.2 Receiver LBT threshold . 13
5.1.4.3 Adjacent channel selectivity. 14
5.1.4.4 Blocking . 14
5.1.4.5 Spurious response rejection . 14
5.1.4.6 Receiver spurious radiation . 14
5.2 Interpretation of measurement results . 14
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 15
Annex B (informative): The EN title in the official languages . 18
Annex C (informative): Bibliography . 19
History . 20

ETSI
5 Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the ETSI standards One-
step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.7].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1].
See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonised Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The present document is part 2 of a multi-part deliverable covering the Short Range Devices (SRD); Radio equipment
to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW, as identified below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive".

National transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.5].
ETSI
6 Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)
1 Scope
The present document applies to the following Short Range Device major equipment types:
1) Non-specific Short Range Devices.
2) Alarms, identification systems, radio-determination, telecommand, telemetry, etc.
3) Radio Frequency Identification (RFID).
4) Detection, movement and alert applications.
These radio equipment types are capable of operating in the frequency bands within the 25 MHz to 1 000 MHz range as
specified in table 1:
• either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna;
• for all types of modulation;
• with or without speech.
Table 1 shows a list of the frequency bands as designated to Short Range Devices by some European Commission
Decisions [i.3] and [i.4] and the CEPT/ERC/REC 70-03 [i.6] as known at the date of publication of the present
document.
NOTE 1: It should be noted that table 1 represents the most widely implemented position within the European
Union and the CEPT countries, but it should not be assumed that all designated bands are available in all
countries.
Table 1: Frequency bands commonly designated to Short Range Devices within 25 MHz to 1 000 MHz
Frequency Bands/Frequencies Applications
Transmit and Receive 26,995 MHz, 27,045 MHz, 27,095 MHz, Model control
27,145 MHz, 27,195 MHz,
34,995 MHz to 35,225 MHz,
40,665 MHz, 40,675 MHz, 40,685 MHz,
40,695 MHz
Transmit and Receive 26,957 MHz to 27,283 MHz Non-specific use
Transmit and Receive 40,660 MHz to 40,700 MHz Non-specific use
Transmit and Receive 138,200 MHz to 138,450 MHz Non-specific use
Transmit and Receive 169,400 MHz to 169,475 MHz Tracking, tracing and data acquisition and
meter reading
Transmit and Receive 169,475 MHz to 169,4875 MHz Social alarms
Transmit and Receive 169,5875 MHz to 169,6000 MHz Social alarms
Transmit and Receive 433,050 MHz to 434,790 MHz Non-specific use
Transmit and Receive 863,000 MHz to 870,000 MHz Non-specific use
Transmit and Receive 864,800 MHz to 865,000 MHz Wireless audio applications
Transmit and Receive 868,000 MHz to 868,600 MHz Non-specific use
Transmit and Receive 868,600 MHz to 868,700 MHz Alarms
Transmit and Receive 868,700 MHz to 869,200 MHz Non-specific use
Transmit and Receive 869,200 MHz to 869,250 MHz Social alarms
Transmit and Receive 869,250 MHz to 869,300 MHz Alarms (0,1 % duty cycle)
Transmit and Receive 869,300 MHz to 869,400 MHz Alarms (1 % duty cycle)
Transmit and Receive 869,400 MHz to 869,650 MHz Non-specific use
Transmit and Receive 869,650 MHz to 869,700 MHz Alarms

NOTE 2: In addition, it should be noted that other frequency bands may be available in a country within the
frequency range 25 MHz to 1 000 MHz for SRD covered by the present document. See European
Commission Decisions on Short Range Devices [i.3] and [i.4] and CEPT/ERC/REC 70-03 [i.6] as
implemented through National Radio Interfaces (NRI) or additional NRI as relevant.
ETSI
7 Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)
NOTE 3: On non-harmonized parameters, national administrations may impose certain conditions such as the type
of modulation, frequency, channel/frequency separations, maximum transmitter radiated power, duty
cycle, and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of
Individual Rights for use of spectrum or General Authorization, or as a condition for use under "licence
exemption" as it is in most cases for Short Range Devices.
The present document covers fixed stations, mobile stations and portable stations.
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.1]
(R&TTE Directive). The present document does not apply to radio equipment for which a specific Harmonized EN
applies as such Harmonized EN may specify additional EN requirements relevant to the presumption of conformity
under article 3.2 of the R&TTE Directive [i.1].
NOTE 4: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 220-1 (V2.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency
range with power levels ranging up to 500 mW; Part 1: Technical characteristics and test
methods".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.2] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.3] Commission Decision 2006/771/EC on harmonization of the radio spectrum for use by short-range
devices as amended by subsequent Commission Decisions.
[i.4] Commission Decision 2005/928/EC on the harmonization of the 169,4-169,8125 MHz frequency
band in the Community as amended by Commission Decision of 13 August 2008.
[i.5] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of candidate Harmonized Standards for application under the R&TTE Directive".
[i.6] CEPT/ERC/REC 70-03: "Relating to the use of Short Range Devices (SRD)".
ETSI
8 Final draft ETSI EN 300 220-2 V2.4.1 (2012-01)
[i.7] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and
...