SIST EN ISO 11833-1:2019

SLOVENSKI STANDARD
SIST EN ISO 11833-1:2019
01-november-2019
Nadomešča:
SIST EN ISO 11833-1:2012
Polimerni materiali - Nemehčane polivinilkloridne plošče - 1. del: Vrste, mere in
značilnosti za plošče z debelino več kot 1 mm (ISO 11833-1:2019)
Plastics - Unplasticized poly(vinyl chloride) sheets - Part 1: Types, dimensions and
characteristics for sheets of thickness not less than 1 mm (ISO 11833-1:2019)
Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften
- Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2019)
Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Partie 1: Types,
dimensions et caractéristiques pour des plaques d'épaisseur non inférieure à 1 mm (ISO
11833-1:2019)
Ta slovenski standard je istoveten z: EN ISO 11833-1:2019
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 11833-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11833-1:2019

---------------------- Page: 2 ----------------------
SIST EN ISO 11833-1:2019


EN ISO 11833-1
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2019
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 11833-1:2012
English Version

Plastics - Unplasticized poly(vinyl chloride) sheets - Part 1:
Types, dimensions and characteristics for sheets of
thickness not less than 1 mm (ISO 11833-1:2019)
Plastiques - Feuilles en poly(chlorure de vinyle) non Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln
plastifié - Partie 1: Types, dimensions et - Teil 1: Typen, Maße und Eigenschaften für Tafeln mit
caractéristiques pour des plaques d'épaisseur non einer Dicke von mindestens 1 mm (ISO 11833-1:2019)
inférieure à 1 mm (ISO 11833-1:2019)
This European Standard was approved by CEN on 21 July 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11833-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11833-1:2019
EN ISO 11833-1:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11833-1:2019
EN ISO 11833-1:2019 (E)
European foreword
This document (EN ISO 11833-1:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2020, and conflicting national standards
shall be withdrawn at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11833-1:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11833-1:2019 has been approved by CEN as EN ISO 11833-1:2019 without any
modification.


3

---------------------- Page: 5 ----------------------
SIST EN ISO 11833-1:2019

---------------------- Page: 6 ----------------------
SIST EN ISO 11833-1:2019
INTERNATIONAL ISO
STANDARD 11833-1
Fourth edition
2019-07
Plastics — Unplasticized poly(vinyl
chloride) sheets —
Part 1:
Types, dimensions and
characteristics for sheets of thickness
not less than 1 mm
Plastiques — Feuilles en poly(chlorure de vinyle) non plastifié —
Partie 1: Types, dimensions et caractéristiques pour des plaques
d'épaisseur non inférieure à 1 mm
Reference number
ISO 11833-1:2019(E)
©
ISO 2019

---------------------- Page: 7 ----------------------
SIST EN ISO 11833-1:2019
ISO 11833-1:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 11833-1:2019
ISO 11833-1:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definition . 2
4 Material . 2
5 Classification . 2
6 Requirements . 2
6.1 Masking . 2
6.2 Appearance . 2
6.3 Dimensions . 3
6.3.1 Length and width . 3
6.3.2 Rectangularity . 3
6.3.3 Thickness . 4
6.4 Basic properties . 4
6.5 Other mechanical and physical properties . 6
6.6 Chemical and physiological properties . 6
6.6.1 Flammability . 6
6.6.2 Chemical resistance . 6
6.6.3 Physiological behaviour . . 6
7 Test methods . 6
7.1 General . 6
7.1.1 Sampling. 6
7.1.2 Preparation of specimens . 6
7.1.3 Conditioning and testing of specimens . 7
7.2 Appearance examination. 7
7.3 Dimensions . 7
7.4 Mechanical properties . 8
7.4.1 Tensile stress at yield and nominal strain at break . 8
7.4.2 Modulus of elasticity in tension . 8
7.4.3 Charpy impact strength of notched specimens . 9
7.5 Thermal properties . 9
7.5.1 Vicat softening temperature . 9
7.5.2 Dimensional change on heating and resistance to delamination . 9
7.6 Total luminous transmittance .11
7.7 Other mechanical and physical properties .11
7.7.1 Charpy impact strength of unnotched specimens .11
7.7.2 Temperature of deflection under load .11
7.7.3 Creep modulus .11
7.7.4 Density .11
7.7.5 Flexural strength .12
7.7.6 Ball indentation hardness .12
7.7.7 Volume resistivity .12
8 Marking .12
Annex A (informative) Determination of resistance to delamination of thick pressed sheets
using a wedge .13
Annex B (informative) Determination of resistance to delamination of thick pressed sheets
by thermal bending.15
© ISO 2019 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 11833-1:2019
ISO 11833-1:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This fourth edition cancels and replaces the third edition (ISO 11833-1:2012), which has been
technically revised. The main changes compared to the previous edition are as follows:
— the title has been editorially revised to read "Plastics — Unplasticized poly(vinyl chloride) sheets —
Part 1: Types, dimensions and characteristics for sheets of thickness not less than 1 mm";
— the "colour" requirements (former 5.3) have been incorporated with the "appearance" requirements
in 6.2 (former 5.2);
— the requirements for measurement at any other temperature (t °C) than 23 °Chas been added to
7.3.1 (former 6.3.1);
— the method of handling the results of 7.4.1, 7.4.2 and 7.4.3 (former 6.4.1 to 6.4.3) have been added;
— “Testing of sheets with a thickness between 1,0 mm and <1,5 mm shall be subject between the
interested parties” has been added in 7.5.1 (former 6.5.1);
— a new Table 7 "Frequency and measurement positions of appearance tests and dimensional
measurements" has been added and the subsequent tables have been renumbered.
A list of all parts in the ISO 11833 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 11833-1:2019
INTERNATIONAL STANDARD ISO 11833-1:2019(E)
Plastics — Unplasticized poly(vinyl chloride) sheets —
Part 1:
Types, dimensions and characteristics for sheets of
thickness not less than 1 mm
1 Scope
This document specifies the requirements for flat extruded sheets and pressed sheets of unplasticized
poly(vinyl chloride) (PVC-U) and the test methods to be used to measure the required values.
It applies only to sheets of thickness not less than 1,0 mm.
It does not cover biaxially stretched PVC-U sheets.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 75-2:2013, Plastics — Determination of temperature of deflection under load — Part 2: Plastics
and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 306:2013, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 472, Plastics — Vocabulary
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-2, Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading
ISO 21306-1:2019, Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion
materials — Part 1: Designation system and basis for specifications
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pycnometer
...