SIST EN 61300-2-35:2015

SLOVENSKI STANDARD
01-april-2015
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHVNXãDQMH1XWDFLMDNDEOD,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-35: Tests - Cable nutation (IEC 61300-2-35:2014)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-35: Prüfungen - Kabelnutation (IEC 61300-2-35:2014)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures
fondamentales d'essais et de mesures - Partie 2-35: Essais - Nutation du câble (CEI
61300-2-35:2014)
Ta slovenski standard je istoveten z: EN 61300-2-35:2014
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 61300-2-35

NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2014
ICS 33.180.20 Supersedes EN 61300-2-35:1997
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-35: Tests -
Cable nutation
(IEC 61300-2-35:2014)
Dispositifs d'interconnexion et composants passifs à fibres Lichtwellenleiter - Verbindungselemente und passive
optiques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-35: Essais - Nutation du câble 35: Prüfungen - Kabelnutation
(CEI 61300-2-35:2014) (IEC 61300-2-35:2014)
This European Standard was approved by CENELEC on 2014-04-11. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61300-2-35:2014 E
Foreword
The text of document 86B/3703/FDIS, future edition 2 of IEC 61300-2-35, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-35:2014.
The following dates are fixed:
– latest date by which the document has to be implemented at (dop) 2015-01-11
national level by publication of an identical national
standard or by endorsement
– latest date by which the national standards conflicting with (dow) 2015-04-11
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document supersedes EN 61300-2-35:1997.
Endorsement notice
The text of the International Standard IEC 61300-2-35:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61753-1 NOTE  Harmonized as EN 61753-1.

- 3 - EN 61300-2-35:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61300-3-1 -  Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -- Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-3 -  Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -- Part 3-3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-4 -  Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures -- Part 3-4:
Examinations and measurements -
Attenuation
IEC 61300-2-35 ®
Edition 2.0 2014-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –
Part 2-35: Tests – Cable nutation

Dispositifs d’interconnexion et composants passifs à fibres optiques –

Procédures fondamentales d’essais et de mesures –

Partie 2-35: Essais – Nutation du câble

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX M
ICS 33.180.20 ISBN 978-2-8322-1395-7

– 2 – IEC 61300-2-35:2014 © IEC 2014
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General description . 6
5 Apparatus . 6
5.1 Design of the apparatus . 6
5.2 Optical measurements . 9
6 Procedure . 9
6.1 Preconditioning . 9
6.2 Initial examinations and measurements . 9
6.3 Conditioning . 10
6.4 Recovery . 10
6.5 Final examinations and measurements . 10
7 Severity . 10
8 Details to be specified . 11
Annex A (informative) Example for a test set-up . 12
Bibliography . 13

Figure 1 – Test apparatus with vertical rotating DUT . 7
Figure 2 – Test apparatus with horizontal rotating DUT . 8
Figure 3 – Test apparatus with rotating deflection unit . 9
Figure A.1 – Example for a test set-up . 12

Table 1 – Severities . 10

IEC 61300-2-35:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-35: Tests – Cable nutation

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent
...