SIST EN ISO 1060-2:2000

SLOVENSKI STANDARD
SIST EN ISO 1060-2:2000
01-maj-2000
3ROLPHUQLPDWHULDOL+RPRLQNRSROLPHULYLQLONORULGDGHO3ULSUDYD
SUHVNXãDQFHYLQGRORþDQMHODVWQRVWL,62
Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of
test samples and determination of properties (ISO 1060-2:1998)
Kunststoffe - Homo- und Copolymere des Vinylchlorids - Teil 2: Herstellung von
Probekörpern und Bestimmung von Eigenschaften (ISO 1060-2:1998)
Plastiques - Résines d'homopolymeres et de copolymeres de chlorure de vinyle - Partie
2: Préparation des échantillons pour essai et détermination des propriétés (ISO 1060-
2:1998)
Ta slovenski standard je istoveten z: EN ISO 1060-2:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 1060-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1060-2:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 1060-2:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 1060-2:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 1060-2:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 1060-2:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 1060-2:2000
INTERNATIONAL ISO
STANDARD 1060-2
Third edition
1998-03-15
Plastics — Homopolymer and copolymer
resins of vinyl chloride —
Part 2:
Preparation of test samples and determination
of properties
Plastiques — Résines d'homopolymères et de copolymères de chlorure de
vinyle —
Partie 2: Préparation des échantillons pour essai et détermination des
propriétés
A
Reference number
ISO 1060-2:1998(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 1060-2:2000
ISO 1060-2:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 1060-2 was prepared by Technical Committee
ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
This third edition cancels and replaces the second edition
(ISO 1060-2:1985) and includes the following main changes:
a) the list of test methods in table 1 has been revised;
b) the preparation of standard pastes has been included.
ISO 1060 consists of the following parts, under the general title Plastics —
Homopolymer and copolymer resins of vinyl chloride:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test samples and determination of properties
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 1060-2:2000
©
INTERNATIONAL STANDARD  ISO ISO 1060-2:1998(E)
Plastics — Homopolymer and copolymer resins of vinyl chloride —
Part 2:
Preparation of test samples and determination of properties
1  Scope
This part of ISO 1060 specified the methods of preparation of test samples and the test methods to be used in
determining the properties of PVC resins. Requirements for handling test material and for conditioning the material
before testing are given here. In addition, properties and test methods which are suitable and necessary to
characterize PVC resins are listed.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of sample
preparation and conditioning and the test procedures specified herein. Values determined will not necessarily be
identical to those obtained using different test samples, or test samples prepared using different procedures.
2  Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part of
ISO 1060. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this part of ISO 1060 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid
International Standards.
ISO 60:1977, Plastics — Determination of apparent density of material that can be poured from a specified funnel.
ISO 1068:1975, Plastics — Homopolymer and copolymer resins of vinyl chloride — Determination of compacted
apparent bulk density.
1)
ISO 1158:— , Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content.
ISO 1159:1978, Plastics — Vinyl chloride-vinyl acetate copolymers — Determination of vinyl acetate.
ISO 1264:1980,
Plastics — Homopolymer and copolymer resins of vinyl chloride — Determination of pH of aqueous
extract.
ISO 1265:1979, Plastics — Polyvinyl chloride resins — Determination of number of impuritie
...