SIST EN 301 489-1 V2.2.3:2020
(Main)ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 1: Common technical requirements - Harmonised Standard for ElectroMagnetic Compatibility
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 1: Common technical requirements - Harmonised Standard for ElectroMagnetic Compatibility
The present document specifies methods of measurements and technical characteristics for radio equipment and associated ancillary equipment, excluding broadcast receivers, in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port of radio equipment and combinations of radio and ancillary equipment are not included in the present document. Such technical specifications are normally found in the relevant product standards for the effective use of the radio spectrum.
NOTE 1: The relationship between the present document and essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] is given in annex A.
NOTE 2: Other standards may apply in place of the present document, e.g. product specific standards in the ETSI EN 301 489 [i.13] series.
Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 1. del: Splošne tehnične zahteve - Harmonizirani standard za elektromagnetno združljivost
V tem dokumentu so opredeljene metode meritev ter tehnične značilnosti radijske opreme in pripadajoče pomožne opreme, razen oddajnih sprejemnikov, v zvezi z elektromagnetno združljivostjo (EMC). Ta dokument ne vključuje tehničnih specifikacij v zvezi z antenskim vhodom radijske opreme in sevalnimi emisijami iz vrat ohišja radijske opreme ter kombinacij radijske in pomožne opreme. Take tehnične specifikacije so običajno navedene v ustreznih standardih za izdelek na področju učinkovite uporabe radijskega spektra.
OPOMBA 1: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.1(b) Direktive 2014/53/EU [i.1] je podano v dodatku A.
OPOMBA 2: Namesto tega dokumenta se lahko uporabljajo drugi standardi, npr. posebni standardi za izdelke iz skupine standardov ETSI EN 301 489 [i.13].
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 301 489-1 V2.2.3 (2019-11)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-1 V2.2.3 (2019-11)
Reference
REN/ERM-EMC-368
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-1 V2.2.3 (2019-11)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 14
3.3 Abbreviations . 14
4 Test conditions . 15
4.1 General . 15
4.2 Arrangements for test signals . 15
4.2.0 General . 15
4.2.1 Arrangements for test signals at the input of transmitters . 15
4.2.2 Arrangements for test signals at the RF output of transmitters . 15
4.2.3 Arrangements for test signals at the RF input of receivers . 15
4.2.4 Arrangements for test signals at the output of receivers . 16
4.3 RF exclusion band of radio equipment . 16
4.3.1 General . 16
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 16
4.3.2.1 General . 16
4.3.2.2 Channelized Equipment . 16
4.3.2.3 Non-Channelized Equipment . 17
4.3.3 Exclusion band for receivers or the receiver part of transceivers . 17
4.3.3.1 Applicability. 17
4.3.3.2 Channelized Equipment . 17
4.3.3.3 Non-Channelized Equipment . 17
4.4 Void . 17
5 Ancillary equipment . 18
6 Performance criteria . 18
6.0 Introduction . 18
6.1 Performance criteria for continuous phenomena . 18
6.2 Performance criteria for transient phenomena . 18
7 Applicability tables. 19
7.0 Introduction . 19
7.1 Emissions . 19
7.2 Immunity . 19
8 Methods of measurement and limits for EMC emissions . 20
8.1 Introduction . 20
8.1.1 Emissions test overview . 20
8.1.2 Test configuration . 20
8.2 Enclosure port . 20
8.2.1 General . 20
8.2.2 Test method . 21
8.2.3 Limits . 21
8.3 DC power input/output ports . 21
8.3.1 General . 21
8.3.2 Test method . 21
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-1 V2.2.3 (2019-11)
8.3.3 Limits . 21
8.4 AC mains power input/output ports . 22
8.4.1 General . 22
8.4.2 Test method . 22
8.4.3 Limits . 22
8.4.3.1 General . 22
8.4.3.2 AC Power port used for power supply only . 22
8.4.3.3 AC power input port also used for in home PLC Communications . 22
8.5 Harmonic current emissions (AC mains input port) . 23
8.6 Voltage fluctuations and flicker (AC mains input port) . 23
8.7 Wired network ports . 23
8.7.1 General . 23
8.7.2 Test method . 23
8.7.3 Limits . 23
9 Test methods and levels for immunity tests . 23
9.1 Test configuration. 23
9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 24
9.2.1 General . 24
9.2.2 Test method . 24
9.2.3 Performance criteria . 25
9.3 Electrostatic discharge . 25
9.3.1 General . 25
9.3.2 Test method . 25
9.3.3 Performance criteria . 25
9.4 Fast transients, common mode . 25
9.4.1 General . 25
9.4.2 Test method . 25
9.4.3 Performance criteria . 26
9.5 Radio frequency, common mode . 26
9.5.1 General . 26
9.5.2 Test method . 26
9.5.3 Performance criteria . 26
9.6 Transients and surges in the vehicular environment . 27
9.6.1 General . 27
9.6.2 Test method . 27
9.6.3 Performance criteria . 27
9.7 Voltage dips and interruptions . 27
9.7.1 General . 27
9.7.2 Test method . 27
9.7.3 Performance criteria . 28
9.8 Surges . 28
9.8.1 General . 28
9.8.2 Test method . 28
9.8.2.0 General . 28
9.8.2.1 Test method for wired network ports directly connected to outdoor cables . 28
9.8.2.2 Test method for wired network ports connected to indoor cables . 29
9.8.2.3 Test method for mains ports . 29
9.8.3 Performance criteria . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 30
Annex B (informative): Application of harmonised EMC standards to multi-radio and multi-
standard-radio equipment . 32
B.1 Introduction . 32
B.2 Multi-radio equipment capable of independent operation . 32
B.3 Multi-radio equipment and multi-standard-radio equipment not capable of independent operation . 32
B.4 Multi-radio equipment comprising of numerous identical radio transmitters . 32
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-1 V2.2.3 (2019-11)
Annex C (informative): Information required by the test laboratory . 33
C.1 Information to be supplied . 33
Annex D (informative): Bibliography . 34
Annex E (informative): Change history . 35
History . 36
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-1 V2.2.3 (2019-11)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.16] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 1 of a multi-part EMC standard for radio equipment which is structured in the following
way:
• All common technical requirements for EMC emission and immunity have been placed in the common part,
which is the present document.
• Separate parts have been developed to cover specific product related radio equipment test conditions, test
arrangements, performance assessment, performance criteria, etc.
• A clause is included in each of the specific radio parts, entitled "special conditions", which is used as
appropriate to cover any deviations or additions to the common requirements set out in the present document.
The present document is part 1 of a multi-part deliverable covering ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services, as identified below:
Part 1: "Common technical requirements";
Part 2: "Specific conditions for radio paging equipment";
Part 3: "Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
246 GHz";
Part 4: "Specific conditions for fixed radio links and ancillary equipment";
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-1 V2.2.3 (2019-11)
Part 5: "Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and
non-speech) and Terrestrial Trunked Radio (TETRA)";
Part 6: "Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment";
Part 9: "Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment,
cordless audio and in-ear monitoring devices";
Part 12: "Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)";
Part 13: "Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)";
Part 15: "Specific conditions for commercially available amateur radio equipment";
Part 17: "Specific conditions for Broadband Data Transmission Systems";
Part 19: "Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band
providing data communications and GNSS receivers operating in the RNSS band (ROGNSS) providing
positioning, navigation, and timing data";
Part 20: "Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)";
Part 22: "Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment";
Part 27: "Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral
devices (ULP-AMI-P) operating in the 402 MHz to 405 MHz bands";
Part 28: "Specific conditions for wireless digital video links";
Part 29: "Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz
and 405 MHz to 406 MHz bands";
Part 31: "Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical
Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)";
Part 33: "Specific conditions for Ultra-WideBand (UWB) devices";
Part 34: "Specific conditions for External Power Supply (EPS) for mobile phones";
Part 35: "Specific requirements for Low Power Active Medical Implants (LP-AMI) operating in the 2 483,5 MHz
to 2 500 MHz bands";
Part 50: "Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment";
Part 51: "Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using
24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz";
Part 52: "Specific conditions for Cellular Communication Mobile and portable radio and ancillary equipment";
Part 53: "Specific conditions for terrestrial sound broadcasting and digital TV broadcasting service transmitters
and associated ancillary equipment";
Part 54: "Specific conditions for ground based aeronautical and meteorological radars".
NOTE: Parts 7, 8, 10, 11, 14, 16, 18, 23, 24, 25, 26 and 32 of this multi-part deliverable have been removed from
this listing as they do not cover the new Directives in force, Directive 2014/53/EU [i.1] and Directive
2014/30/EU [i.2].
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-1 V2.2.3 (2019-11)
National transposition dates
Date of adoption of this EN: 18 November 2019
Date of latest announcement of this EN (doa): 29 February 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 2020
Date of withdrawal of any conflicting National Standard (dow): 31 August 2021
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Product dependent arrangements necessary to perform the EMC tests on dedicated types of radio communications
equipment, and the assessment of test results, are detailed in the appropriate relevant radio technology parts of ETSI
EN 301 489 series [i.13] details of which can be found in annex C of the present document.
The environment classification used in the present document refers to the environment classification used in:
• CENELEC EN 61000-6-3 [i.4] and CENELEC EN 61000-6-1 [i.5] for the residential, commercial and light
industrial environment; or
• CENELEC EN 61000-6-2 [i.15] and CENELEC EN 61000-6-4 [i.14] for the industrial environment; or
• ETSI TR 101 651 [i.6] for the telecommunication centre environment; or
• ISO 7637-2 [8] for the vehicular environment.
The immunity requirements within the present document are derived from the generic immunity standard for the
residential, commercial and light industrial environment.
When it is required to evaluate the EMC performance of "combined radio and non-radio equipment", ETSI
EG 203 367 [i.3] provides guidance upon the application of the various harmonised standards, including the present
document, that could potentially apply to such equipment.
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 489-1 V2.2.3 (2019-11)
1 Scope
The present document specifies methods of measurements and technical characteristics for radio equipment and
associated ancillary equipment, excluding broadcast receivers, in respect of ElectroMagnetic Compatibility (EMC).
Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port
of radio equipment and combinations of radio and ancillary equipment are not included in the present document. Such
technical specifications are normally found in the relevant product standards for the effective use of the radio spectrum.
NOTE 1: The relationship between the present document and essential requirements of article 3.1(b) of Directive
2014/53/EU [i.1] is given in annex A.
NOTE 2: Other standards may apply in place of the pre
...
Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
Reference
REN/ERM-EMC-368
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 14
3.3 Abbreviations . 14
4 Test conditions . 15
4.1 General . 15
4.2 Arrangements for test signals . 15
4.2.0 General . 15
4.2.1 Arrangements for test signals at the input of transmitters . 15
4.2.2 Arrangements for test signals at the RF output of transmitters . 15
4.2.3 Arrangements for test signals at the RF input of receivers . 15
4.2.4 Arrangements for test signals at the output of receivers . 16
4.3 RF exclusion band of radio equipment . 16
4.3.1 General . 16
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 16
4.3.2.1 General . 16
4.3.2.2 Channelized Equipment . 16
4.3.2.3 Non-Channelized Equipment . 17
4.3.3 Exclusion band for receivers or the receiver part of transceivers . 17
4.3.3.1 Applicability. 17
4.3.3.2 Channelized Equipment . 17
4.3.3.3 Non-Channelized Equipment . 17
4.4 Void . 17
5 Ancillary equipment . 18
6 Performance criteria . 18
6.0 Introduction . 18
6.1 Performance criteria for continuous phenomena . 18
6.2 Performance criteria for transient phenomena . 18
7 Applicability tables. 19
7.0 Introduction . 19
7.1 Emissions . 19
7.2 Immunity . 19
8 Methods of measurement and limits for EMC emissions . 20
8.1 Introduction . 20
8.1.1 Emissions test overview . 20
8.1.2 Test configuration . 20
8.2 Enclosure port . 20
8.2.1 General . 20
8.2.2 Test method . 21
8.2.3 Limits . 21
8.3 DC power input/output ports . 21
8.3.1 General . 21
8.3.2 Test method . 21
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
8.3.3 Limits . 21
8.4 AC mains power input/output ports . 22
8.4.1 General . 22
8.4.2 Test method . 22
8.4.3 Limits . 22
8.4.3.1 General . 22
8.4.3.2 AC Power port used for power supply only . 22
8.4.3.3 AC power input port also used for in home PLC Communications . 22
8.5 Harmonic current emissions (AC mains input port) . 23
8.6 Voltage fluctuations and flicker (AC mains input port) . 23
8.7 Wired network ports . 23
8.7.1 General . 23
8.7.2 Test method . 23
8.7.3 Limits . 23
9 Test methods and levels for immunity tests . 23
9.1 Test configuration. 23
9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 24
9.2.1 General . 24
9.2.2 Test method . 24
9.2.3 Performance criteria . 25
9.3 Electrostatic discharge . 25
9.3.1 General . 25
9.3.2 Test method . 25
9.3.3 Performance criteria . 25
9.4 Fast transients, common mode . 25
9.4.1 General . 25
9.4.2 Test method . 25
9.4.3 Performance criteria . 26
9.5 Radio frequency, common mode . 26
9.5.1 General . 26
9.5.2 Test method . 26
9.5.3 Performance criteria . 26
9.6 Transients and surges in the vehicular environment . 27
9.6.1 General . 27
9.6.2 Test method . 27
9.6.3 Performance criteria . 27
9.7 Voltage dips and interruptions . 27
9.7.1 General . 27
9.7.2 Test method . 27
9.7.3 Performance criteria . 28
9.8 Surges . 28
9.8.1 General . 28
9.8.2 Test method . 28
9.8.2.0 General . 28
9.8.2.1 Test method for wired network ports directly connected to outdoor cables . 28
9.8.2.2 Test method for wired network ports connected to indoor cables . 29
9.8.2.3 Test method for mains ports . 29
9.8.3 Performance criteria . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 30
Annex B (informative): Application of harmonised EMC standards to multi-radio and multi-
standard-radio equipment . 32
B.1 Introduction . 32
B.2 Multi-radio equipment capable of independent operation . 32
B.3 Multi-radio equipment and multi-standard-radio equipment not capable of independent operation . 32
B.4 Multi-radio equipment comprising of numerous identical radio transmitters . 32
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
Annex C (informative): Information required by the test laboratory . 33
C.1 Information to be supplied . 33
Annex D (informative): Bibliography . 34
Annex E (informative): Change history . 35
History . 36
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.16] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 1 of a multi-part EMC standard for radio equipment which is structured in the following
way:
• All common technical requirements for EMC emission and immunity have been placed in the common part,
which is the present document.
• Separate parts have been developed to cover specific product related radio equipment test conditions, test
arrangements, performance assessment, performance criteria, etc.
• A clause is included in each of the specific radio parts, entitled "special conditions", which is used as
appropriate to cover any deviations or additions to the common requirements set out in the present document.
The present document is part 1 of a multi-part deliverable covering ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services, as identified below:
Part 1: "Common technical requirements";
Part 2: "Specific conditions for radio paging equipment";
Part 3: "Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
246 GHz";
Part 4: "Specific conditions for fixed radio links and ancillary equipment";
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
Part 5: "Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and
non-speech) and Terrestrial Trunked Radio (TETRA)";
Part 6: "Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment";
Part 9: "Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment,
cordless audio and in-ear monitoring devices";
Part 12: "Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)";
Part 13: "Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)";
Part 15: "Specific conditions for commercially available amateur radio equipment";
Part 17: "Specific conditions for Broadband Data Transmission Systems";
Part 19: "Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band
providing data communications and GNSS receivers operating in the RNSS band (ROGNSS) providing
positioning, navigation, and timing data";
Part 20: "Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)";
Part 22: "Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment";
Part 27: "Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral
devices (ULP-AMI-P) operating in the 402 MHz to 405 MHz bands";
Part 28: "Specific conditions for wireless digital video links";
Part 29: "Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz
and 405 MHz to 406 MHz bands";
Part 31: "Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical
Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)";
Part 33: "Specific conditions for Ultra-WideBand (UWB) devices";
Part 34: "Specific conditions for External Power Supply (EPS) for mobile phones";
Part 35: "Specific requirements for Low Power Active Medical Implants (LP-AMI) operating in the 2 483,5 MHz
to 2 500 MHz bands";
Part 50: "Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment";
Part 51: "Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using
24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz";
Part 52: "Specific conditions for Cellular Communication Mobile and portable radio and ancillary equipment";
Part 53: "Specific conditions for terrestrial sound broadcasting and digital TV broadcasting service transmitters
and associated ancillary equipment";
Part 54: "Specific conditions for ground based aeronautical and meteorological radars".
NOTE: Parts 7, 8, 10, 11, 14, 16, 18, 23, 24, 25, 26 and 32 of this multi-part deliverable have been removed from
this listing as they do not cover the new Directives in force, Directive 2014/53/EU [i.1] and Directive
2014/30/EU [i.2].
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Product dependent arrangements necessary to perform the EMC tests on dedicated types of radio communications
equipment, and the assessment of test results, are detailed in the appropriate relevant radio technology parts of ETSI
EN 301 489 series [i.13] details of which can be found in annex C of the present document.
The environment classification used in the present document refers to the environment classification used in:
• CENELEC EN 61000-6-3 [i.4] and CENELEC EN 61000-6-1 [i.5] for the residential, commercial and light
industrial environment; or
• CENELEC EN 61000-6-2 [i.15] and CENELEC EN 61000-6-4 [i.14] for the industrial environment; or
• ETSI TR 101 651 [i.6] for the telecommunication centre environment; or
• ISO 7637-2 [8] for the vehicular environment.
The immunity requirements within the present document are derived from the generic immunity standard for the
residential, commercial and light industrial environment.
When it is required to evaluate the EMC performance of "combined radio and non-radio equipment", ETSI
EG 203 367 [i.3] provides guidance upon the application of the various harmonised standards, including the present
document, that could potentially apply to such equipment.
ETSI
---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 301 489-1 V2.2.2 (2019-09)
1 Scope
The present document specifies methods of measurements and technical characteristics for radio equipment and
associated ancillary equipment, excluding broadcast receivers, in respect of ElectroMagnetic Compatibility (EMC).
Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port
of radio equipment and combinations of radio and associated ancillary equipment are not included in the present
document. Such technical specifications are normally found in the relevant product standards for the effective use of the
radio spectrum.
N
...
Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Reference
REN/ERM-EMC-368
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 14
3.3 Abbreviations . 14
4 Test conditions . 15
4.1 General . 15
4.2 Arrangements for test signals . 15
4.2.0 General . 15
4.2.1 Arrangements for test signals at the input of transmitters . 15
4.2.2 Arrangements for test signals at the RF output of transmitters . 15
4.2.3 Arrangements for test signals at the RF input of receivers . 15
4.2.4 Arrangements for test signals at the output of receivers . 16
4.3 RF exclusion band of radio equipment . 16
4.3.1 General . 16
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 16
4.3.2.1 General . 16
4.3.2.2 Channelized Equipment . 16
4.3.2.3 Non-Channelized Equipment . 17
4.3.3 Exclusion band for receivers or the receiver part of transceivers . 17
4.3.3.1 Applicability. 17
4.3.3.2 Channelized Equipment . 17
4.3.3.3 Non-Channelized Equipment . 17
4.4 Void . 17
5 Ancillary equipment . 18
6 Performance criteria . 18
6.0 Introduction . 18
6.1 Performance criteria for continuous phenomena . 18
6.2 Performance criteria for transient phenomena . 18
7 Applicability tables. 19
7.0 Introduction . 19
7.1 Emissions . 19
7.2 Immunity . 19
8 Methods of measurement and limits for EMC emissions . 20
8.1 Introduction . 20
8.1.1 Emissions test overview . 20
8.1.2 Test configuration . 20
8.2 Enclosure port . 20
8.2.1 General . 20
8.2.2 Test method . 21
8.2.3 Limits . 21
8.3 DC power input/output ports . 21
8.3.1 General . 21
8.3.2 Test method . 21
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
8.3.3 Limits . 21
8.4 AC mains power input/output ports . 22
8.4.1 General . 22
8.4.2 Test method . 22
8.4.3 Limits . 22
8.4.3.1 General . 22
8.4.3.2 AC Power port used for power supply only . 22
8.4.3.3 AC power input port also used for PLC Communications . 22
8.5 Harmonic current emissions (AC mains input port) . 23
8.6 Voltage fluctuations and flicker (AC mains input port) . 23
8.7 Wired network ports . 23
8.7.1 General . 23
8.7.2 Test method . 23
8.7.3 Limits . 23
9 Test methods and levels for immunity tests . 23
9.1 Test configuration. 23
9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 24
9.2.1 General . 24
9.2.2 Test method . 24
9.2.3 Performance criteria . 25
9.3 Electrostatic discharge . 25
9.3.1 General . 25
9.3.2 Test method . 25
9.3.3 Performance criteria . 25
9.4 Fast transients, common mode . 25
9.4.1 General . 25
9.4.2 Test method . 25
9.4.3 Performance criteria . 26
9.5 Radio frequency, common mode . 26
9.5.1 General . 26
9.5.2 Test method . 26
9.5.3 Performance criteria . 26
9.6 Transients and surges in the vehicular environment . 27
9.6.1 General . 27
9.6.2 Test method . 27
9.6.3 Performance criteria . 27
9.7 Voltage dips and interruptions . 27
9.7.1 General . 27
9.7.2 Test method . 27
9.7.3 Performance criteria . 28
9.8 Surges . 28
9.8.1 General . 28
9.8.2 Test method . 28
9.8.2.0 General . 28
9.8.2.1 Test method for wired network ports directly connected to outdoor cables . 28
9.8.2.2 Test method for wired network ports connected to indoor cables . 29
9.8.2.3 Test method for mains ports . 29
9.8.3 Performance criteria . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 30
A.1 Relationship between the present document and the essential requirements of Directive
2014/53/EU . 30
Annex B (informative): Application of harmonised EMC standards to multi-radio and multi-
standard-radio equipment . 32
B.1 Introduction . 32
B.2 Multi-radio equipment capable of independent operation . 32
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
B.3 Multi-radio equipment and multi-standard-radio equipment not capable of independent operation . 32
B.4 Multi-radio equipment comprising of numerous identical radio transmitters . 32
Annex C (informative): Information required by the test laboratory . 33
C.1 Information to be supplied . 33
Annex D (informative): Bibliography . 34
Annex E (informative): Change history . 35
History . 36
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.16] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under the Directives, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of the corresponding Directives
and associated EFTA regulations.
The present document is part 1 of a multi-part EMC standard for radio equipment which is structured in the following
way:
• All common technical requirements for EMC emission and immunity have been placed in the common part,
which is the present document.
• Separate parts have been developed to cover specific product related radio equipment test conditions, test
arrangements, performance assessment, performance criteria, etc.
• A clause is included in each of the specific radio parts, entitled "special conditions", which is used as
appropriate to cover any deviations or additions to the common requirements set out in the present document.
The present document is part 1 of a multi-part deliverable covering ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services, as identified below:
Part 1: "Common technical requirements;
Part 2: "Specific conditions for radio paging equipment";
Part 3: "Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
246 GHz";
Part 4: "Specific conditions for fixed radio links and ancillary equipment";
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Part 5: "Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and
non-speech) and Terrestrial Trunked Radio (TETRA)";
Part 6: "Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment";
Part 9: "Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment,
cordless audio and in-ear monitoring devices";
Part 12: "Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)";
Part 13: "Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)";
Part 15: "Specific conditions for commercially available amateur radio equipment";
Part 17: "Specific conditions for Broadband Data Transmission Systems";
Part 19: "Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band
providing data communications and GNSS receivers operating in the RNSS band (ROGNSS) providing
positioning, navigation, and timing data";
Part 20: "Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)";
Part 22: "Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment";
Part 27: "Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral
devices (ULP-AMI-P) operating in the 402 MHz to 405 MHz bands";
Part 28: "Specific conditions for wireless digital video links";
Part 29: "Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz
and 405 MHz to 406 MHz bands";
Part 31: "Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical
Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)";
Part 33: "Specific conditions for Ultra Wide Band (UWB) devices";
Part 34: "Specific conditions for External Power Supply (EPS) for mobile phones";
Part 35: "Specific requirements for Low Power Active Medical Implants (LP-AMI) operating in the 2 483,5 MHz
to 2 500 MHz bands";
Part 50: "Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment";
Part 51: "Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using
24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz";
Part 52: "Specific conditions for Cellular Communication Mobile and portable radio and ancillary equipment";
Part 53: "Specific conditions for terrestrial sound broadcasting and digital TV broadcasting service transmitters
and associated ancillary equipment";
Part 54: "Specific conditions for ground based aeronautical and meteorological radars".
NOTE: Parts 7, 8, 10, 11, 14, 16, 18, 23, 24, 25, 26 and 32 of this multi-part deliverable have been removed from
this listing as they do not cover the new Directive in force, Directive 2014/53/EU [i.1] and Directive
2014/30/EU [i.2].
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Product dependent arrangements necessary to perform the EMC tests on dedicated types of radio communications
equipment, and the assessment of test results, are detailed in the appropriate relevant radio technology parts of ETSI
EN 301 489 series [i.13] details of which can be found in annex C of the present document.
The environment classification used in the present document refers to the environment classification used in:
• CENELEC EN 61000-6-3 [i.4] and CENELEC EN 61000-6-1 [i.5] for the residential, commercial and light
industrial environment; or
• CENELEC EN 61000-6-2 [i.15] and CENELEC EN 61000-6-4 [i.14] for the industrial environment; or
• ETSI TR 101 651 [i.6] for the telecommunication centre environment; or
• ISO 7637-2 [8] for the vehicular environment.
The immunity requirements within the present document are derived from the generic immunity standard for the
residential, commercial and light industrial environment.
When it is required to evaluate the EMC performance of "combined radio and non-radio equipment", ETSI
EG 203 367 [i.3] provides guidance upon the application of the various harmonised standards, including the present
document, that could potentially apply to such equipment.
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
1 Scope
The present document specifies methods of measurements and technical characteristics for radio equipment and
associated ancillary equipment, excluding broadcast receivers, in respect of ElectroMagnetic Compatibility (EMC).
Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port
of radio equipmen
...
SLOVENSKI STANDARD
SIST EN 301 489-1 V2.2.3:2020
01-januar-2020
Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 1.
del: Splošne tehnične zahteve - Harmonizirani standard za elektromagnetno
združljivost
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 1:
Common technical requirements - Harmonised Standard for ElectroMagnetic
Compatibility
Ta slovenski standard je istoveten z: ETSI EN 301 489-1 V2.2.3 (2019-11)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 301 489-1 V2.2.3:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 301 489-1 V2.2.3:2020
---------------------- Page: 2 ----------------------
SIST EN 301 489-1 V2.2.3:2020
ETSI EN 301 489-1 V2.2.3 (2019-11)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 3 ----------------------
SIST EN 301 489-1 V2.2.3:2020
2 ETSI EN 301 489-1 V2.2.3 (2019-11)
Reference
REN/ERM-EMC-368
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 489-1 V2.2.3:2020
3 ETSI EN 301 489-1 V2.2.3 (2019-11)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 14
3.3 Abbreviations . 14
4 Test conditions . 15
4.1 General . 15
4.2 Arrangements for test signals . 15
4.2.0 General . 15
4.2.1 Arrangements for test signals at the input of transmitters . 15
4.2.2 Arrangements for test signals at the RF output of transmitters . 15
4.2.3 Arrangements for test signals at the RF input of receivers . 15
4.2.4 Arrangements for test signals at the output of receivers . 16
4.3 RF exclusion band of radio equipment . 16
4.3.1 General . 16
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 16
4.3.2.1 General . 16
4.3.2.2 Channelized Equipment . 16
4.3.2.3 Non-Channelized Equipment . 17
4.3.3 Exclusion band for receivers or the receiver part of transceivers . 17
4.3.3.1 Applicability. 17
4.3.3.2 Channelized Equipment . 17
4.3.3.3 Non-Channelized Equipment . 17
4.4 Void . 17
5 Ancillary equipment . 18
6 Performance criteria . 18
6.0 Introduction . 18
6.1 Performance criteria for continuous phenomena . 18
6.2 Performance criteria for transient phenomena . 18
7 Applicability tables. 19
7.0 Introduction . 19
7.1 Emissions . 19
7.2 Immunity . 19
8 Methods of measurement and limits for EMC emissions . 20
8.1 Introduction . 20
8.1.1 Emissions test overview . 20
8.1.2 Test configuration . 20
8.2 Enclosure port . 20
8.2.1 General . 20
8.2.2 Test method . 21
8.2.3 Limits . 21
8.3 DC power input/output ports . 21
8.3.1 General . 21
8.3.2 Test method . 21
ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 489-1 V2.2.3:2020
4 ETSI EN 301 489-1 V2.2.3 (2019-11)
8.3.3 Limits . 21
8.4 AC mains power input/output ports . 22
8.4.1 General . 22
8.4.2 Test method . 22
8.4.3 Limits . 22
8.4.3.1 General . 22
8.4.3.2 AC Power port used for power supply only . 22
8.4.3.3 AC power input port also used for in home PLC Communications . 22
8.5 Harmonic current emissions (AC mains input port) . 23
8.6 Voltage fluctuations and flicker (AC mains input port) . 23
8.7 Wired network ports . 23
8.7.1 General . 23
8.7.2 Test method . 23
8.7.3 Limits . 23
9 Test methods and levels for immunity tests . 23
9.1 Test configuration. 23
9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 24
9.2.1 General . 24
9.2.2 Test method . 24
9.2.3 Performance criteria . 25
9.3 Electrostatic discharge . 25
9.3.1 General . 25
9.3.2 Test method . 25
9.3.3 Performance criteria . 25
9.4 Fast transients, common mode . 25
9.4.1 General . 25
9.4.2 Test method . 25
9.4.3 Performance criteria . 26
9.5 Radio frequency, common mode . 26
9.5.1 General . 26
9.5.2 Test method . 26
9.5.3 Performance criteria . 26
9.6 Transients and surges in the vehicular environment . 27
9.6.1 General . 27
9.6.2 Test method . 27
9.6.3 Performance criteria . 27
9.7 Voltage dips and interruptions . 27
9.7.1 General . 27
9.7.2 Test method . 27
9.7.3 Performance criteria . 28
9.8 Surges . 28
9.8.1 General . 28
9.8.2 Test method . 28
9.8.2.0 General . 28
9.8.2.1 Test method for wired network ports directly connected to outdoor cables . 28
9.8.2.2 Test method for wired network ports connected to indoor cables . 29
9.8.2.3 Test method for mains ports . 29
9.8.3 Performance criteria . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 30
Annex B (informative): Application of harmonised EMC standards to multi-radio and multi-
standard-radio equipment . 32
B.1 Introduction . 32
B.2 Multi-radio equipment capable of independent operation . 32
B.3 Multi-radio equipment and multi-standard-radio equipment not capable of independent operation . 32
B.4 Multi-radio equipment comprising of numerous identical radio transmitters . 32
ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 489-1 V2.2.3:2020
5 ETSI EN 301 489-1 V2.2.3 (2019-11)
Annex C (informative): Information required by the test laboratory . 33
C.1 Information to be supplied . 33
Annex D (informative): Bibliography . 34
Annex E (informative): Change history . 35
History . 36
ETSI
---------------------- Page: 7 ----------------------
SIST EN 301 489-1 V2.2.3:2020
6 ETSI EN 301 489-1 V2.2.3 (2019-11)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.16] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 1 of a multi-part EMC standard for radio equipment which is structured in the following
way:
• All common technical requirements for EMC emission and immunity have been placed in the common part,
which is the present document.
• Separate parts have been developed to cover specific product related radio equipment test conditions, test
arrangements, performance assessment, performance criteria, etc.
• A clause is included in each of the specific radio parts, entitled "special conditions", which is used as
appropriate to cover any deviations or additions to the common requirements set out in the present document.
The present document is part 1 of a multi-part deliverable covering ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services, as identified below:
Part 1: "Common technical requirements";
Part 2: "Specific conditions for radio paging equipment";
Part 3: "Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
246 GHz";
Part 4: "Specific conditions for fixed radio links and ancillary equipment";
ETSI
---------------------- Page: 8 ----------------------
SIST EN 301 489-1 V2.2.3:2020
7 ETSI EN 301 489-1 V2.2.3 (2019-11)
Part 5: "Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and
non-speech) and Terrestrial Trunked Radio (TETRA)";
Part 6: "Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment";
Part 9: "Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment,
cordless audio and in-ear monitoring devices";
Part 12: "Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)";
Part 13: "Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)";
Part 15: "Specific conditions for commercially available amateur radio equipment";
Part 17: "Specific conditions for Broadband Data Transmission Systems";
Part 19: "Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band
providing data communications and GNSS receivers operating in the RNSS band (ROGNSS) providing
positioning, navigation, and timing data";
Part 20: "Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)";
Part 22: "Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment";
Part 27: "Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral
devices (ULP-AMI-P) operating in the 402 MHz to 405 MHz bands";
Part 28: "Specific conditions for wireless digital video links";
Part 29: "Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz
and 405 MHz to 406 MHz bands";
Part 31: "Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical
Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)";
Part 33: "Specific conditions for Ultra-WideBand (UWB) devices";
Part 34: "Specific conditions for External Power Supply (EPS) for mobile phones";
Part 35: "Specific requirements for Low Power Active Medical Implants (LP-AMI) operating in the 2 483,5 MHz
to 2 500 MHz bands";
Part 50: "Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment";
Part 51: "Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using
24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz";
Part 52: "Specific conditions for Cellular Communication Mobile and portable radio and ancillary equipment";
Part 53: "Specific conditions for terrestrial sound broadcasting and digital TV broadcasting service transmitters
and associated ancillary equipment";
Part 54: "Specific conditions for ground based aeronautical and meteorological radars".
NOTE: Parts 7, 8, 10, 11, 14, 16, 18, 23, 24, 25, 26 and 32 of this multi-part deliverable have been removed from
this listing as they do not cover the new Directives in force, Directive 2014/53/EU [i.1] and Directive
2014/30/EU [i.2].
ETSI
---------------------- Page: 9 ----------------------
SIST EN 301 489-1 V2.2.3:2020
8 ETSI EN 301 489-1 V2.2.3 (2019-11)
National transposition dates
Date of adoption of this EN: 18 November 2019
Date of latest announcement of this EN (doa): 29 February 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 2020
Date of withdrawal of any conflicting National Standard (dow): 31 August 2021
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Product dependent arrangements necessary to perform the EMC tests on dedicated types of radio communications
equipment, and the assessment of test results, are detailed in the appropriate relevant radio technology parts of ETSI
EN 301 489 series [i.13] details of which can be found in annex C of the present document.
The environment classification used in the present document refers to the environment classification used in:
• CENELEC EN 61000-6-3 [i.4] and CENELEC EN 61000-6-1 [i.5] for the residential, commercial and light
industrial environment; or
• CENELEC EN 61000-6-2 [i.15] and CENELEC EN 61000-6-4 [i.14] for the industrial environment; or
• ETSI TR 101 651 [i.6] for the telecommunication centre environment; or
• ISO 7637-2 [8] for the vehicular environment.
The immunity requirements within the present document are derived from the generic immunity standard for the
residential, commercial and light
...
Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU and the essential
requirements of article 6 of Directive 2014/30/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Reference
REN/ERM-EMC-368
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 15
3.3 Abbreviations . 15
4 Test conditions . 16
4.1 General . 16
4.2 Arrangements for test signals . 16
4.2.0 General . 16
4.2.1 Arrangements for test signals at the input of transmitters . 16
4.2.2 Arrangements for test signals at the RF output of transmitters . 16
4.2.3 Arrangements for test signals at the RF input of receivers . 17
4.2.4 Arrangements for test signals at the output of receivers . 17
4.2.5 Arrangements for testing transmitter and receiver together (as a system) . 17
4.3 RF exclusion band of radio equipment . 18
4.3.1 General . 18
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 18
4.3.2.1 General . 18
4.3.2.2 Channelized Equipment . 18
4.3.2.3 Non-Channelized Equipment . 18
4.3.3 Exclusion band for receivers or the receiver part of transceivers . 18
4.3.3.1 Applicability. 18
4.3.3.2 Channelized Equipment . 18
4.3.3.3 Non-Channelized Equipment . 19
4.4 Narrow band responses of receivers or receivers which are part of transceivers . 19
4.5 Normal test modulation . 19
5 Performance assessment . 20
5.1 General . 20
5.2 Equipment which can provide a continuous communication link . 20
5.3 Equipment which does not provide a continuous communication link . 21
5.4 Ancillary equipment . 21
5.5 Equipment classification . 21
6 Performance criteria . 22
6.0 Introduction . 22
6.1 Performance criteria for continuous phenomena applied to transmitters and receivers . 22
6.2 Performance criteria for transient phenomena applied to transmitters and receivers . 22
6.3 Performance criteria for equipment which does not provide a continuous communication link . 23
6.4 Performance criteria for ancillary equipment tested on a stand alone basis . 23
7 Applicability overview tables . 23
7.0 Introduction . 23
7.1 EMC emission . 24
7.2 Immunity . 24
8 Methods of measurement and limits for EMC emissions . 25
8.1 Test configuration. 25
8.2 Enclosure port of ancillary equipment measured on a stand alone basis . 25
8.2.1 General . 25
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
8.2.2 Test method . 26
8.2.3 Limits . 26
8.3 DC power input/output ports . 26
8.3.1 General . 26
8.3.2 Test method . 26
8.3.3 Limits . 27
8.4 AC mains power input/output ports . 27
8.4.1 General . 27
8.4.2 Test method . 27
8.4.3 Limits . 28
8.4.3.1 General . 28
8.4.3.2 AC Power port used for power supply only . 28
8.4.3.3 AC power input port also used for PLC Communications . 28
8.5 Harmonic current emissions (AC mains input port) . 28
8.6 Voltage fluctuations and flicker (AC mains input port) . 28
8.7 Wired network ports . 28
8.7.1 General . 28
8.7.2 Test method . 28
8.7.3 Limits . 29
9 Test methods and levels for immunity tests . 29
9.1 Test configuration. 29
9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 29
9.2.1 General . 29
9.2.2 Test method . 30
9.2.3 Performance criteria . 30
9.3 Electrostatic discharge . 30
9.3.1 General . 30
9.3.2 Test method . 30
9.3.3 Performance criteria . 31
9.4 Fast transients, common mode . 31
9.4.1 General . 31
9.4.2 Test method . 31
9.4.3 Performance criteria . 31
9.5 Radio frequency, common mode . 32
9.5.1 General . 32
9.5.2 Test method . 32
9.5.3 Performance criteria . 32
9.6 Transients and surges in the vehicular environment . 33
9.6.1 General . 33
9.6.2 Test method . 33
9.6.3 Performance criteria . 33
9.7 Voltage dips and interruptions . 33
9.7.1 General . 33
9.7.2 Test method . 33
9.7.3 Performance criteria . 34
9.8 Surges . 34
9.8.1 General . 34
9.8.2 Test method . 35
9.8.2.0 General . 35
9.8.2.1 Test method for wired network ports directly connected to outdoor cables . 35
9.8.2.2 Test method for wired network ports connected to indoor cables . 35
9.8.2.3 Test method for mains ports . 35
9.8.3 Performance criteria . 35
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU and Directive 2014/30/EU . 36
A.1 Relationship between the present document and the essential requirements of Directive
2014/53/EU . 36
A.2 Relationship between the present document and the essential requirements of Directive
2014/30/EU . 37
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Annex B (normative): Application of harmonised EMC standards to multi-radio and multi-
standard-radio equipment . 39
B.1 Introduction . 39
B.2 Multi-radio equipment capable of independent transmission. 39
B.3 Multi-radio equipment and multi-standard-radio equipment not capable of independent
transmission . 39
B.4 Multi-radio equipment comprising of numerous identical radio transmitters . 39
Annex C (informative): Bibliography . 40
Annex D (informative): Change history . 41
History . 42
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.16] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
The present document has been prepared under the Commission's standardisation request C(2016) 7641 final [i.17] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/30/EU on the harmonisation
of the laws of the Member States relating to electromagnetic compatibility (recast) [i.2].
Once the present document is cited in the Official Journal of the European Union under the Directives, compliance with
the normative clauses of the present document given in tables A.1 and A.2 confers, within the limits of the scope of the
present document, a presumption of conformity with the corresponding essential requirements of the corresponding
Directives and associated EFTA regulations.
The present document is part 1 of a multi-part EMC standard for radio equipment which is structured in the following
way:
• One EMC standard for all radio equipment made up of several parts.
• All common technical requirements for EMC emission and immunity have been placed in the common part,
which is the present document.
• Separate parts have been developed to cover specific product related radio equipment test conditions, test
arrangements, performance assessment, performance criteria, etc.
• A clause is included in each of the specific radio parts, entitled "special conditions", which is used as
appropriate to cover any deviations or additions to the common requirements set out in the present document.
The present document is part 1 of a multi-part deliverable covering ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services, as identified below:
Part 1: "Common technical requirements;
Part 2: "Specific conditions for radio paging equipment";
Part 3: "Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
246 GHz";
Part 4: "Specific conditions for fixed radio links and ancillary equipment";
Part 5: "Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and
non-speech) and Terrestrial Trunked Radio (TETRA)";
Part 6: "Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment";
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Part 9: "Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment,
cordless audio and in-ear monitoring devices";
Part 12: "Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)";
Part 13: "Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)";
Part 15: "Specific conditions for commercially available amateur radio equipment";
Part 17: "Specific conditions for Broadband Data Transmission Systems";
Part 19: "Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band
providing data communications";
Part 20: "Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)";
Part 22: "Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment";
Part 27: "Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral
devices (ULP-AMI-P)";
Part 28: "Specific conditions for wireless digital video links";
Part 29: "Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz
and 405 MHz to 406 MHz bands";
Part 31: "Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical
Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)";
Part 33: "Specific conditions for Ultra Wide Band (UWB) devices";
Part 34: "Specific conditions for External Power Supply (EPS) for mobile phones";
Part 35: "Specific requirements for Low Power Active Medical Implants (LP-AMI) operating in the 2 483,5 MHz
to 2 500 MHz bands";
Part 50: "Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment";
Part 51: "Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using
24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz";
Part 52: "Specific conditions for Cellular Communication Mobile and portable (UE) radio and ancillary
equipment";
Part 53: "Specific conditions for terrestrial sound broadcasting and digital TV broadcasting service transmitters
and associated ancillary equipment".
NOTE: Parts 7, 8, 10, 11, 14, 16, 18, 23, 24, 25, 26 and 32 of this multi-part deliverable have been removed from
this listing as they do not cover the new Directive in force, Directive 2014/53/EU [i.1] and Directive
2014/30/EU [i.2].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
1 Scope
The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] and article 6 of
Directive 2014/30/EU [i.2] for radio equipment and associated ancillary equipment, excluding broadcast receivers, in
respect of ElectroMagnetic Compatibility (EMC).
NOTE 1: Where the present document is being used to evaluate the EMC performance of "combined radio and non-
radio equipment", ETSI EG 203 367 [i.3] provides guidance upon the application of the various
harmonised standards, including the present document, that could potentially apply to such equipment.
Product dependent arrangements necessary to perform the EMC tests on dedicated types of radio communications
equipment, and the assessment of test results, are detailed in the appropriate relevant radio technology parts of ETSI
EN 301 489 series [i.13].
The present document, together with the relevant radio technology part, where required, specifies the applicable EMC
tests, the methods of measurement, the limits and the performance criteria for radio equipment
...
SLOVENSKI STANDARD
oSIST prEN 301 489-1 V2.2.1:2019
01-maj-2019
6WDQGDUGHOHNWURPDJQHWQH]GUXåOMLYRVWL (0& ]DUDGLMVNRRSUHPRLQVWRULWYH
GHO 6SORãQHWHKQLþQH]DKWHYH+DUPRQL]LUDQLVWDQGDUG]DHOHNWURPDJQHWQR
]GUXåOMLYRVW
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 1:
Common technical requirements - Harmonised Standard for ElectroMagnetic
Compatibility
Ta slovenski standard je istoveten z: ETSI EN 301 489-1 V2.2.1 (2019-03)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN 301 489-1 V2.2.1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
---------------------- Page: 2 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 3 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
2 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Reference
REN/ERM-EMC-368
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
3 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 14
3.3 Abbreviations . 14
4 Test conditions . 15
4.1 General . 15
4.2 Arrangements for test signals . 15
4.2.0 General . 15
4.2.1 Arrangements for test signals at the input of transmitters . 15
4.2.2 Arrangements for test signals at the RF output of transmitters . 15
4.2.3 Arrangements for test signals at the RF input of receivers . 15
4.2.4 Arrangements for test signals at the output of receivers . 16
4.3 RF exclusion band of radio equipment . 16
4.3.1 General . 16
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 16
4.3.2.1 General . 16
4.3.2.2 Channelized Equipment . 16
4.3.2.3 Non-Channelized Equipment . 17
4.3.3 Exclusion band for receivers or the receiver part of transceivers . 17
4.3.3.1 Applicability. 17
4.3.3.2 Channelized Equipment . 17
4.3.3.3 Non-Channelized Equipment . 17
4.4 Void . 17
5 Ancillary equipment . 18
6 Performance criteria . 18
6.0 Introduction . 18
6.1 Performance criteria for continuous phenomena . 18
6.2 Performance criteria for transient phenomena . 18
7 Applicability tables. 19
7.0 Introduction . 19
7.1 Emissions . 19
7.2 Immunity . 19
8 Methods of measurement and limits for EMC emissions . 20
8.1 Introduction . 20
8.1.1 Emissions test overview . 20
8.1.2 Test configuration . 20
8.2 Enclosure port . 20
8.2.1 General . 20
8.2.2 Test method . 21
8.2.3 Limits . 21
8.3 DC power input/output ports . 21
8.3.1 General . 21
8.3.2 Test method . 21
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
4 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
8.3.3 Limits . 21
8.4 AC mains power input/output ports . 22
8.4.1 General . 22
8.4.2 Test method . 22
8.4.3 Limits . 22
8.4.3.1 General . 22
8.4.3.2 AC Power port used for power supply only . 22
8.4.3.3 AC power input port also used for PLC Communications . 22
8.5 Harmonic current emissions (AC mains input port) . 23
8.6 Voltage fluctuations and flicker (AC mains input port) . 23
8.7 Wired network ports . 23
8.7.1 General . 23
8.7.2 Test method . 23
8.7.3 Limits . 23
9 Test methods and levels for immunity tests . 23
9.1 Test configuration. 23
9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 24
9.2.1 General . 24
9.2.2 Test method . 24
9.2.3 Performance criteria . 25
9.3 Electrostatic discharge . 25
9.3.1 General . 25
9.3.2 Test method . 25
9.3.3 Performance criteria . 25
9.4 Fast transients, common mode . 25
9.4.1 General . 25
9.4.2 Test method . 25
9.4.3 Performance criteria . 26
9.5 Radio frequency, common mode . 26
9.5.1 General . 26
9.5.2 Test method . 26
9.5.3 Performance criteria . 26
9.6 Transients and surges in the vehicular environment . 27
9.6.1 General . 27
9.6.2 Test method . 27
9.6.3 Performance criteria . 27
9.7 Voltage dips and interruptions . 27
9.7.1 General . 27
9.7.2 Test method . 27
9.7.3 Performance criteria . 28
9.8 Surges . 28
9.8.1 General . 28
9.8.2 Test method . 28
9.8.2.0 General . 28
9.8.2.1 Test method for wired network ports directly connected to outdoor cables . 28
9.8.2.2 Test method for wired network ports connected to indoor cables . 29
9.8.2.3 Test method for mains ports . 29
9.8.3 Performance criteria . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 30
A.1 Relationship between the present document and the essential requirements of Directive
2014/53/EU . 30
Annex B (informative): Application of harmonised EMC standards to multi-radio and multi-
standard-radio equipment . 32
B.1 Introduction . 32
B.2 Multi-radio equipment capable of independent operation . 32
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
5 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
B.3 Multi-radio equipment and multi-standard-radio equipment not capable of independent operation . 32
B.4 Multi-radio equipment comprising of numerous identical radio transmitters . 32
Annex C (informative): Information required by the test laboratory . 33
C.1 Information to be supplied . 33
Annex D (informative): Bibliography . 34
Annex E (informative): Change history . 35
History . 36
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
6 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.16] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under the Directives, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of the corresponding Directives
and associated EFTA regulations.
The present document is part 1 of a multi-part EMC standard for radio equipment which is structured in the following
way:
• All common technical requirements for EMC emission and immunity have been placed in the common part,
which is the present document.
• Separate parts have been developed to cover specific product related radio equipment test conditions, test
arrangements, performance assessment, performance criteria, etc.
• A clause is included in each of the specific radio parts, entitled "special conditions", which is used as
appropriate to cover any deviations or additions to the common requirements set out in the present document.
The present document is part 1 of a multi-part deliverable covering ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services, as identified below:
Part 1: "Common technical requirements;
Part 2: "Specific conditions for radio paging equipment";
Part 3: "Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
246 GHz";
Part 4: "Specific conditions for fixed radio links and ancillary equipment";
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
7 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Part 5: "Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and
non-speech) and Terrestrial Trunked Radio (TETRA)";
Part 6: "Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment";
Part 9: "Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment,
cordless audio and in-ear monitoring devices";
Part 12: "Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)";
Part 13: "Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)";
Part 15: "Specific conditions for commercially available amateur radio equipment";
Part 17: "Specific conditions for Broadband Data Transmission Systems";
Part 19: "Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band
providing data communications and GNSS receivers operating in the RNSS band (ROGNSS) providing
positioning, navigation, and timing data";
Part 20: "Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)";
Part 22: "Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment";
Part 27: "Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral
devices (ULP-AMI-P) operating in the 402 MHz to 405 MHz bands";
Part 28: "Specific conditions for wireless digital video links";
Part 29: "Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz
and 405 MHz to 406 MHz bands";
Part 31: "Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical
Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)";
Part 33: "Specific conditions for Ultra Wide Band (UWB) devices";
Part 34: "Specific conditions for External Power Supply (EPS) for mobile phones";
Part 35: "Specific requirements for Low Power Active Medical Implants (LP-AMI) operating in the 2 483,5 MHz
to 2 500 MHz bands";
Part 50: "Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment";
Part 51: "Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using
24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz";
Part 52: "Specific conditions for Cellular Communication Mobile and portable radio and ancillary equipment";
Part 53: "Specific conditions for terrestrial sound broadcasting and digital TV broadcasting service transmitters
and associated ancillary equipment";
Part 54: "Specific conditions for ground based aeronautical and meteorological radars".
NOTE: Parts 7, 8, 10, 11, 14, 16, 18, 23, 24, 25, 26 and 32 of this multi-part deliverable have been removed from
this listing as they do not cover the new Directive in force, Directive 2014/53/EU [i.1] and Directive
2014/30/EU [i.2].
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 301 489-1 V2.2.1:2019
8 Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Product dependent arrangements necessary to perform the EMC tests on dedicated types of radio communications
equipment, and the assessment of test results, are detailed in the appropriate relevant radio technology parts of ETSI
EN 301 489 series [i.13] details of which can be found in annex C of the present document.
The environment classification used in the present document refers to the environment classification used in:
• CENELEC EN 61000-6-3 [i.4] and CENELEC EN 6
...
SLOVENSKI STANDARD
oSIST prEN 301 489-1 V2.2.0:2017
01-maj-2017
6WDQGDUGHOHNWURPDJQHWQH]GUXåOMLYRVWL (0& ]DUDGLMVNRRSUHPRLQVWRULWYH
GHO 6SORãQHWHKQLþQH]DKWHYH+DUPRQL]LUDQLVWDQGDUGNL]DMHPDELVWYHQH
]DKWHYHþOHQD E GLUHNWLYH(8LQELVWYHQH]DKWHYHþOHQDGLUHNWLYH
(8
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 1:
Common technical requirements - Harmonised Standard covering the essential
requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of
article 6 of Directive 2014/30/EU
Ta slovenski standard je istoveten z: ETSI EN 301 489-1 V2.2.0 (2017-03)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN 301 489-1 V2.2.0:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
---------------------- Page: 2 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU and the essential
requirements of article 6 of Directive 2014/30/EU
---------------------- Page: 3 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
2 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Reference
REN/ERM-EMC-368
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
3 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 15
3.3 Abbreviations . 15
4 Test conditions . 16
4.1 General . 16
4.2 Arrangements for test signals . 16
4.2.0 General . 16
4.2.1 Arrangements for test signals at the input of transmitters . 16
4.2.2 Arrangements for test signals at the RF output of transmitters . 16
4.2.3 Arrangements for test signals at the RF input of receivers . 17
4.2.4 Arrangements for test signals at the output of receivers . 17
4.2.5 Arrangements for testing transmitter and receiver together (as a system) . 17
4.3 RF exclusion band of radio equipment . 18
4.3.1 General . 18
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 18
4.3.2.1 General . 18
4.3.2.2 Channelized Equipment . 18
4.3.2.3 Non-Channelized Equipment . 18
4.3.3 Exclusion band for receivers or the receiver part of transceivers . 18
4.3.3.1 Applicability. 18
4.3.3.2 Channelized Equipment . 18
4.3.3.3 Non-Channelized Equipment . 19
4.4 Narrow band responses of receivers or receivers which are part of transceivers . 19
4.5 Normal test modulation . 19
5 Performance assessment . 20
5.1 General . 20
5.2 Equipment which can provide a continuous communication link . 20
5.3 Equipment which does not provide a continuous communication link . 21
5.4 Ancillary equipment . 21
5.5 Equipment classification . 21
6 Performance criteria . 22
6.0 Introduction . 22
6.1 Performance criteria for continuous phenomena applied to transmitters and receivers . 22
6.2 Performance criteria for transient phenomena applied to transmitters and receivers . 22
6.3 Performance criteria for equipment which does not provide a continuous communication link . 23
6.4 Performance criteria for ancillary equipment tested on a stand alone basis . 23
7 Applicability overview tables . 23
7.0 Introduction . 23
7.1 EMC emission . 24
7.2 Immunity . 24
8 Methods of measurement and limits for EMC emissions . 25
8.1 Test configuration. 25
8.2 Enclosure port of ancillary equipment measured on a stand alone basis . 25
8.2.1 General . 25
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
4 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
8.2.2 Test method . 26
8.2.3 Limits . 26
8.3 DC power input/output ports . 26
8.3.1 General . 26
8.3.2 Test method . 26
8.3.3 Limits . 27
8.4 AC mains power input/output ports . 27
8.4.1 General . 27
8.4.2 Test method . 27
8.4.3 Limits . 28
8.4.3.1 General . 28
8.4.3.2 AC Power port used for power supply only . 28
8.4.3.3 AC power input port also used for PLC Communications . 28
8.5 Harmonic current emissions (AC mains input port) . 28
8.6 Voltage fluctuations and flicker (AC mains input port) . 28
8.7 Wired network ports . 28
8.7.1 General . 28
8.7.2 Test method . 28
8.7.3 Limits . 29
9 Test methods and levels for immunity tests . 29
9.1 Test configuration. 29
9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 29
9.2.1 General . 29
9.2.2 Test method . 30
9.2.3 Performance criteria . 30
9.3 Electrostatic discharge . 30
9.3.1 General . 30
9.3.2 Test method . 30
9.3.3 Performance criteria . 31
9.4 Fast transients, common mode . 31
9.4.1 General . 31
9.4.2 Test method . 31
9.4.3 Performance criteria . 31
9.5 Radio frequency, common mode . 32
9.5.1 General . 32
9.5.2 Test method . 32
9.5.3 Performance criteria . 32
9.6 Transients and surges in the vehicular environment . 33
9.6.1 General . 33
9.6.2 Test method . 33
9.6.3 Performance criteria . 33
9.7 Voltage dips and interruptions . 33
9.7.1 General . 33
9.7.2 Test method . 33
9.7.3 Performance criteria . 34
9.8 Surges . 34
9.8.1 General . 34
9.8.2 Test method . 35
9.8.2.0 General . 35
9.8.2.1 Test method for wired network ports directly connected to outdoor cables . 35
9.8.2.2 Test method for wired network ports connected to indoor cables . 35
9.8.2.3 Test method for mains ports . 35
9.8.3 Performance criteria . 35
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU and Directive 2014/30/EU . 36
A.1 Relationship between the present document and the essential requirements of Directive
2014/53/EU . 36
A.2 Relationship between the present document and the essential requirements of Directive
2014/30/EU . 37
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
5 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Annex B (normative): Application of harmonised EMC standards to multi-radio and multi-
standard-radio equipment . 39
B.1 Introduction . 39
B.2 Multi-radio equipment capable of independent transmission. 39
B.3 Multi-radio equipment and multi-standard-radio equipment not capable of independent
transmission . 39
B.4 Multi-radio equipment comprising of numerous identical radio transmitters . 39
Annex C (informative): Bibliography . 40
Annex D (informative): Change history . 41
History . 42
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
6 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.16] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
The present document has been prepared under the Commission's standardisation request C(2016) 7641 final [i.17] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/30/EU on the harmonisation
of the laws of the Member States relating to electromagnetic compatibility (recast) [i.2].
Once the present document is cited in the Official Journal of the European Union under the Directives, compliance with
the normative clauses of the present document given in tables A.1 and A.2 confers, within the limits of the scope of the
present document, a presumption of conformity with the corresponding essential requirements of the corresponding
Directives and associated EFTA regulations.
The present document is part 1 of a multi-part EMC standard for radio equipment which is structured in the following
way:
• One EMC standard for all radio equipment made up of several parts.
• All common technical requirements for EMC emission and immunity have been placed in the common part,
which is the present document.
• Separate parts have been developed to cover specific product related radio equipment test conditions, test
arrangements, performance assessment, performance criteria, etc.
• A clause is included in each of the specific radio parts, entitled "special conditions", which is used as
appropriate to cover any deviations or additions to the common requirements set out in the present document.
The present document is part 1 of a multi-part deliverable covering ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services, as identified below:
Part 1: "Common technical requirements;
Part 2: "Specific conditions for radio paging equipment";
Part 3: "Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
246 GHz";
Part 4: "Specific conditions for fixed radio links and ancillary equipment";
Part 5: "Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and
non-speech) and Terrestrial Trunked Radio (TETRA)";
Part 6: "Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment";
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
7 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Part 9: "Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment,
cordless audio and in-ear monitoring devices";
Part 12: "Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)";
Part 13: "Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)";
Part 15: "Specific conditions for commercially available amateur radio equipment";
Part 17: "Specific conditions for Broadband Data Transmission Systems";
Part 19: "Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band
providing data communications";
Part 20: "Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)";
Part 22: "Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment";
Part 27: "Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral
devices (ULP-AMI-P)";
Part 28: "Specific conditions for wireless digital video links";
Part 29: "Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz
and 405 MHz to 406 MHz bands";
Part 31: "Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical
Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)";
Part 33: "Specific conditions for Ultra Wide Band (UWB) devices";
Part 34: "Specific conditions for External Power Supply (EPS) for mobile phones";
Part 35: "Specific requirements for Low Power Active Medical Implants (LP-AMI) operating in the 2 483,5 MHz
to 2 500 MHz bands";
Part 50: "Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment";
Part 51: "Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using
24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz";
Part 52: "Specific conditions for Cellular Communication Mobile and portable (UE) radio and ancillary
equipment";
Part 53: "Specific conditions for terrestrial sound broadcasting and digital TV broadcasting service transmitters
and associated ancillary equipment".
NOTE: Parts 7, 8, 10, 11, 14, 16, 18, 23, 24, 25, 26 and 32 of this multi-part deliverable have been removed from
this listing as they do not cover the new Directive in force, Directive 2014/53/EU [i.1] and Directive
2014/30/EU [i.2].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 301 489-1 V2.2.0:2017
8 Draft ETSI EN 301 489-1 V2.2.0 (2017-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.