SIST EN 302 208-2 V1.1.1:2005

SLOVENSKI STANDARD
01-februar-2005
(OHNWURPDJQHWQD]GUXåOMLYRVW(0&LQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP(50
±2SUHPD]DLGHQWLILNDFLMRUDGLMVNLKIUHNYHQFNLGHOXMHMRYSDVXRG0+]GR
0+]]PRþQRVWQLPLQLYRMLGR:±GHO+DUPRQL]LUDQL(1YVNODGXVþOHQRP
GLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio Frequency
Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up
to 2 W; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 302 208-2 Version 1.1.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

Candidate Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Radio Frequency Identification Equipment operating in the
band 865 MHz to 868 MHz with power levels up to 2 W;
Part 2: Harmonized EN under article 3.2
of the R&TTE Directive
2 ETSI EN 302 208-2 V1.1.1 (2004-09)

Reference
DEN/ERM-TG34-001-2
Keywords
ID, radio, regulation, short range, terrestrial
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2004.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI EN 302 208-2 V1.1.1 (2004-09)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .6
1 Scope.8
2 References.8
3 Definitions, symbols and abbreviations .9
3.1 Definitions.9
3.2 Symbols.9
3.3 Abbreviations.9
4 Technical requirements specifications.9
4.1 Interrogators.9
4.1.1 General performance criteria .9
4.2 Transmitter requirements.9
4.2.1 Frequency error.9
4.2.2 Frequency stability under low voltage conditions .10
4.2.3 Effective radiated power.10
4.2.4 Transmitter antenna beamwidth.10
4.2.5 Transmitter spectrum mask.10
4.2.6 Spurious emissions.10
4.2.7 Transmission times.10
4.3 Receiver requirements.10
4.3.1 Receiver threshold in listen mode.10
4.3.2 Listen time.10
4.3.3 Blocking or desensitisation in listen mode .10
4.3.4 Spurious emissions.10
4.4 Tag requirements.11
4.4.1 Emissions outside sub-band edges.11
5 Testing for compliance with technical requirements.11
5.1 Essential radio test suites.11
5.1.1 Environmental conditions for testing.11
5.1.1.1 Normal and extreme test conditions.11
5.1.1.2 Test power sources.11
5.1.2 Choice of samples for test suite .11
5.1.3 Transmitter test suites.11
5.1.3.1 Frequency error.11
5.1.3.2 Frequency stability under low voltage conditions.11
5.1.3.3 Effective radiated power .11
5.1.3.4 Transmitter antenna beamwidth .11
5.1.3.5 Transmitter spectrum mask.11
5.1.3.6 Spurious emissions.11
5.1.3.7 Transmission times.12
5.1.4 Receiver test suites.12
5.1.4.1 Receiver threshold in listen mode .12
5.1.4.2 Listen time.12
5.1.4.3 Blocking or desensitisation in listen mode.12
5.1.4.4 Spurious emissions.12
5.1.5 Tag test suites .12
5.1.5.1 Emissions outside sub-band edges .12
6 Interpretation of the measurement results .12
Annex A (normative): The EN Requirements Table (EN-RT) .14
ETSI
4 ETSI EN 302 208-2 V1.1.1 (2004-09)
Annex B (informative): Bibliography.15
Annex C (informative): The EN title in the official languages .16
History .17

ETSI
5 ETSI EN 302 208-2 V1.1.1 (2004-09)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical
Committee Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC of the European Parliament and of
the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering Radio Frequency Identification Equipment
operating in the band 865 MHz to 868 MHz with power levels up to 2 W, as identified below:
Part 1: "Technical requirements and methods of measurement";
Part 2 "Harmonized EN under article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 3 September 2004
Date of latest announcement of this EN (doa): 31 December 2004
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2005
Date of withdrawal of any conflicting National Standard (dow): 30 June 2006

ETSI
6 ETSI EN 302 208-2 V1.1.1 (2004-09)
Introduction
The present document is part of a set of standards designed to fit in a modular structure to cover all radio and
telecommunications terminal equipment under the R&TTE Directive [1]. Each standard is a module in the structure.
The modular structure is shown in figure 1.

Disability*
3.3f
Emergency*
3.3e
Fraud*
3.3d
3.3c
Privacy*
No harm to the network*
3.3b
* If needed
Scoped by
Inter-working via the network*
equipment
3.3a class or type
Inter-working with the network
Use of spectrum
3.2
New radio harmonized standards
Spectrum
Scoped by frequency and/or equipment type
Radio Product EMC
EN 301 489 multi-part EMC standard
3.1b
EMC
Generic and product standards also notified under EMC Directive
- If needed, new standards for human exposure to
Electromagnetic Fields,
- if needed, new standards for acoustic safety
3.1a
Standards also notified under LV Directive
Safety
Non-radio Radio (RE)
TTE Non-TTE
Figure 1: Modular structure for the various standards used under the R&TTE Directive [1]
ETSI
7 ETSI EN 302 208-2 V1.1.1 (2004-09)
The left hand edge of the figure 1 shows the different clauses of article 3 of the R&TTE Directive [1].
For article 3.3 various horizontal boxes are shown. Dotted lines indicate that at the time of publication of the present
document essential requirements in these areas have to be adopted by the Commission. If such essential requirements
are adopted, and as far and as long as they are applicable, they will justify individual standards whose scope is likely to
be specified by function or interface type.
The vertical boxes show the standards under article 3.2 for the use of the radio spectrum by radio equipment. The
scopes of these standards are specified either by frequency (normally in the case where frequency bands are
harmonized) or by radio equipment type.
For article 3.1b the diagram shows EN 301 489, the multi-part product EMC standard for radio used under the
EMC Directive [8].
For article 3.1a the diagram shows the existing safety standards currently used under the LV Directive [7] and new
standards covering human exposure to electromagnetic fields. New standards covering acoustic safety may also be
required.
The bottom of the figure shows the relationship of the standards to radio equipment and telecommunications terminal
equipment. A particular equipment may be radio equipment, telecommunications terminal equipment or both. A radio
spectrum standard will apply if it is radio equipment. An article 3.3 standard will apply as well only if the relevant
essential requirement under the R&TTE Directive is adopted by the Commission and if the equipment in question is
covered by the scope of the corresponding standard. Thus, depending on the nature of the equipment, the essential
requirements under the R&TTE Directive may be covered in a set of standards.
The modularit
...